2003 TOYOTA AVENSIS ground

APPENDIX
Vehicle GradeBody Type
Min. Running Ground Clearance mm (in.)
Angle of Approach degrees
Angle of Departure degrees
Item Area
Model Code
Overall Length mm (in.)
Width mm (in.)
Height mm (in.)
Wheel Base mm (in.)
Tread Front mm (in.)
Rear mm (in.)
Room Front mm (in.)
Rear mm (in.)
Overhang
Curb Weight
Gross Vehicle Weight Front kg (lb)
Rear kg (lb)
Total kg (lb)
Front kg (lb)
Rear kg (lb)
Total kg (lb)
Fuel Tank Capacity (Imp.gal.)
Luggage Compartment Capacity m
3 (cu.ft.)
Max. Speed km / h (mph)
Max. Cruising Speed km / h (mph)
Acceleration
Max. Permissible
Speed
Min. Turning Radius 0 to 100 km / h sec.
0 to 400 m sec.
1st Gear km / h (mph)
2nd Gear km
/h (mph)
3rd Gear km / h (mph)
4th Gear km / h (mph)
Tire m (ft.)
Body m (ft.)
Engine Type
Valve Mechanism
Bore x Stroke mm (in.)
Displacement cm
3 (cu.in.)
Compression Ratio
Carburetor Type or Injection Pump Type (Diesel)Research Octane No. or Cetane No. (Diesel)
Max. Output (EEC) kW / rpm
Max. Torque (EEC) N
.m / rpm
Battery Capacity (5HR) Voltage & Amp. hr.
Alternator Output Watts
Starter Output kW
Clutch Type
Transaxle Type
Transmission Gear
Ratio
Counter Gear Ratio
Differential Gear Ratio (Final)
Brake Type
Parking Brake Type
Brake Booster Type and Size in.
Proportioning Valve Type
Suspension Type
Stabilizer Bar
Steering Gear Type
Steering Gear Ratio (Overall)
Power Steering Type In First
In Second
In Third
In Fourth
In Fifth
In Reverse
Front
Rear
Front
Rear
Front
Rear
5
10
15
20
25
30
35
40
45
50
55
60
65
70
Major Dimension & Vehicle Weights
Performance
Engine
Engine
Chassis Electric
EUROPE
5-Door Wagon
MID ELEGANT
Length mm (in.)
Width mm (in.)
Height mm (in.) ENTRY
AP-18
AZT250R-AWPGHW AZT250L-AWPGHW CDT250R-AWMNYW CDT250L-AWMNYW
4700 (185.0) 4700 (185.0)4700 (185.0)4700 (185.0)
1760 (69.3) 1760 (69.3)1760 (69.3)1760 (69.3)
1525 (60.0) 1525 (60.0)1525 (60.0)1525 (60.0)
2700 (106.3) 2700 (106.3)2700 (106.3)2700 (106.3)
1506 (59.3) 1506 (59.3)1506 (59.3)1506 (59.3)
1510 (59.4) 1510 (59.4)1510 (59.4)1510 (59.4)
2090 (82.3) 2090 (82.3)2090 (82.3)2090 (82.3)
1485 (58.5) 1485 (58.5)1485 (58.5)1485 (58.5)
1210 (47.6), 1160 (45.7)*
11210 (47.6), 1160 (45.7)*11210 (47.6), 1160 (45.7)*11210 (47.6), 1160 (45.7)*1
910 (35.8) 910 (35.8)910 (35.8)910 (35.8)
1095 (43.1) 1095 (43.1)1095 (43.1)1095 (43.1)
135 (5.3), 155 (6.1)*
2135 (5.3), 155 (6.1)*2135 (5.3), 155 (6.1)*2135 (5.3), 155 (6.1)*2
13.1
, 14.5
*213.1
, 14.5
*213.1
, 14.5
*213.1
, 14.5
*2
18
, 19.2
*218
, 19.2
*218
, 19.2
*218
, 19.2
*2
800 - 825 (1764 - 1819) 800 - 825 (1764 - 1819) 850 - 900 (1874 - 1984) 850 - 900 (1874 - 1984)
585 - 595 (1290 - 1312) 585 - 595 (1290 - 1312) 580 - 590 (1279 - 1301) 580 - 590 (1279 - 1301)
1385 - 1420 (3054 - 3131) 1385 - 1420 (3054 - 3131) 1430 - 1490 (3153 - 3285) 1430 - 1490 (3153 - 3285) 915 (2017) 915 (2017)985 (2172)985 (2172)
980 (2161) 980 (2161)985 (2172)985 (2172)
1895 (4178) 1895 (4178)1970 (4344)1970 (4344)
60 (15.9, 13.2) 60 (15.9, 13.2)60 (15.9, 13.2)60 (15.9, 13.2)
0.520 (18.4) 0.520 (18.4)0.520 (18.4)0.520 (18.4)
190 (118) 190 (118)190 (118)190 (118)
ÐÐÐÐ
11.3 11.311.411.4
17.7 17.717.817.8
63 (39) 63 (39)45 (27)45 (27)
114 (71) 114 (71) 84 (52)84 (52)
177 (110) 177 (110) 128 (79)128 (79)
Ð Ð176 (109) 176 (109)
5.6 (18.4) 5.6 (18.4)5.6 (18.4)5.6 (18.4)
5.995 (19.7) 5.995 (19.7)5.995 (19.7)5.995 (19.7)
1AZ-FSE 1AZ-FSE1CD-FTV 1CD-FTV
16-Valve, DOHC 16-Valve, DOHC16-Valve, DOHC16-Valve, DOHC
86.0 x 86.0 (3.39 x 3.39) 86.0 x 86.0 (3.39 x 3.39) 82.2 x 94.0 (3.24 x 3.70) 82.2 x 94.0 (3.24 x 3.70)
1998 (121.9) 1998 (121.9)1995 (121.7)1995 (121.7)
11.0 11.017.8 17.8
EFI EFICommon-Rail Type Common-Rail Type
95 or higher 95 or higher48 or higher48 or higher
108 / 5700 108 / 5700 85 / 360085 / 3600
196 / 4000 196 / 4000280 / 2000 - 2200 280 / 2000 - 2200
12 - 48 12 - 4812 - 6012 - 60
1200 120012001200
1.6 1.62.02.0
Ð ÐDry, Single Plate Dry, Single Plate
U241E*
4U241E*4E357 E357
3.943 3.9433.5383.538
2.197 2.1971.9131.913
1.413 1.4131.2581.258
1.020 1.0200.9180.918
Ð Ð0.690 0.690
3.145 3.1453.5833.583
ÐÐÐÐ
2.923 2.9233.6843.684
Ventilated Disc Ventilated DiscVentilated DiscVentilated Disc
Solid Disc Solid DiscSolid DiscSolid Disc
Drum DrumDrumDrum
Tandem 8º + 9º Tandem 8º + 9ºTandem 8º + 9ºTandem 8º + 9º
ÐÐÐÐ
MacPherson Strut. MacPherson Strut.MacPherson Strut.MacPherson Strut.
Double Wishbone Double WishboneDouble WishboneDouble Wishbone
STD STDSTDSTD
STD STDSTDSTD
Rack and Pinion Rack and PinionRack and PinionRack and Pinion
16.1 16.116.116.1
Integral Type Integral TypeIntegral TypeIntegral Type
*
1: With Sun Roof *4: Snow Mord Type
*2: Rough Road Pack
*3: Option
http://vnx.su

Z17005
Fig. 2
Sensor
C BA
ECU
1 2 1
2 2
1
B04722
Fig. 3
Sensor
B2
A
1
2 1
2 21
C
B1
1
2 ECU
Z17007
Fig. 4
Sensor
C BA
1
2 1
2 2
15V
5V
0V
01±34
±
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
AVENSIS REPAIR MANUAL (RM1018E)
(b) Check the continuity. (1) Disconnect connectors A and C and measure theresistance between them.
Resistance: 1
or less
HINT:
Measure the resistance while lightly shaking the wire harness
vertically and horizontally. In the case of Fig. 2:
Between terminal 1 of connector A and terminal 1
of connector C
No continuity (open)
Between terminal 2 of connector A and terminal 2
of connector C
Continuity
Therefore, the cause is an open circuit between ter-
minal 1 of connector A and terminal 1 of connector
C.
(2) Disconnect connector B and measure the resis-
tance between the connectors.
In the case of Fig. 3:
Between terminal 1 of connector A and terminal 1
of connector B1
Continuity
Between terminal 1 of connector B2 and terminal 1
of connector C
No continuity (open)
Therefore, the cause is an open circuit between ter-
minal 1 of connector B2 and terminal 1 of connector
C.
(c) Check the voltage. (1) In a circuit in which voltage is applied (to the ECUconnector terminal), an open circuit can be checked
by conducting a voltage check.
As shown in Fig. 4, with each connector still con-
nected, measure the voltage between the body
ground and terminal 1 of connector A at the ECU 5
V output terminal, terminal 1 of connector B, and
terminal 1 of connector C, in that order.
(2) If the results are: 5 V: Between terminal 1 of connector A and body
ground
5 V: Between terminal 1 of connector B and body
ground
0 V: Between terminal 1 of connector C and body
ground
Therefore, the cause is an open circuit in the wire
harness between terminal 1 of connector B and ter-
minal 1 of connector C.
http://vnx.su

Z17008
CSHORT
1
2 B
1
2 1
2
A
Fig. 5
Z17009
Fig. 6
Sensor
C BA
ECU
1
2 1
2 2
1
Z17808
Fig. 7
Sensor B2
A
11 1
CB1
1ECU
2 22 2
±
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS01±35
AVENSIS REPAIR MANUAL (RM1018E)
3. CHECK SHORT CIRCUIT
(a) If the wire harness is ground shorted as shown in Fig. 5,
locate the section by conducting a continuity check with
the body ground in step (b).
(b) Check the continuity with the body ground. (1) Disconnect connectors A and C and measure the
resistance between terminals 1 and 2 of connector
A and the body ground.
Resistance: 10 k
or higher
HINT:
Measure the resistance while lightly shaking the wire harness
vertically and horizontally.
In the case of Fig. 6:
Between terminal 1 of connector A and body
ground Continuity (short)
Between terminal 2 of connector A and body
ground No continuity
Therefore, the cause is a short circuit between ter-
minal 1 of connector A and terminal 1 of connector
C.
(2) Disconnect connector B and measure the resis- tance between terminal 1 of connector A and the
body ground, and terminal 1 of connector B2 and
the body ground.
In the case of Fig. 7:
Between terminal 1 of connector A and body
ground No continuity
Between terminal 1 of connector B2 and body
ground Continuity (short)
Therefore, the cause is a short circuit between ter-
minal 1 of connector B2 and terminal 1 of connector
C.
http://vnx.su

IN0383
ExampleGround
IN0384
Ground
ECU Side
W/H Side
Ground
01±36±
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
AVENSIS REPAIR MANUAL (RM1018E)
4. CHECK AND REPLACE ECU
NOTICE:

Start an inspection of the connector from the back-
side of the connector on the wire harness side with
the connector connected to the ECU.

When no measurement condition is specified, per-
form the inspection with the engine stopped and also
the ignition switch ON.
(a) First check the ECU ground circuit. If it is faulty, repair it. If it is normal, the ECU could be faulty. In this case, re-
place the ECU with one that functions normally and check
if the symptoms appear.
(1) Measure the resistance between the ECU groundterminal and body ground.
Resistance: 1
or less
(2) Disconnect the ECU connector, check the ground terminals on the ECU side and wire harness side for
bends and check the contact pressure.
http://vnx.su

Detection Item
Indicates the system or details of the
problem. Trouble Area
Indicates the suspect areas of
the problem.
Detection Item
DTC No.
(See page)
Trouble Area
SRS

Steering wheel pad (squib)

Spiral cable

Airbag sensor assembly

Wire harness
B0103/12
(05±132) B0102/11
(05±128)
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, check the circuit for that code liste\
d in the table
below (Proceed to the page given for that circuit).

Short in D squib circuit

Open in D squib circuit
B0101/14
(05±124)

Short in D squib circuit (to ground)

Short in D squib circuit (to B+)
Warning Light
ON
ON
ON
ON

Steering wheel pad (squib)

Spiral cable

Airbag sensor assembly

Wire harness

Steering wheel pad (squib)

Spiral cable

Airbag sensor assembly

Wire harness

Steering wheel pad (squib)

Spiral cable

Airbag sensor assembly

Wire harness
B0105/53
(05±136) ON

Airbag sensor assembly

Wire harness
B0106/54
Open in P squib circuit

Airbag sensor assembly

Wire harness

Short in P squib circuit (to Ground) ON
ON
B0100/13
(05±119)

Short in P squib circuit
Front passenger airbag assembly (squib)

Airbag sensor assembly

Wire harness

Front passenger airbag assembly (squib)

Front passenger airbag assembly (squib)
Page or Instructions
Indicates the page where the inspection proce-
dures for each circuit is to be found, or gives
instructions for checking and repairs.


DTC No.
Indicates the diagnostic trouble code.



±
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS01±29
AVENSIS REPAIR MANUAL (RM1018E)
DIAGNOSTIC TROUBLE CODE CHART
The inspection procedures are shown in the table below. This table allows efficient and accurate trouble-
shooting using the diagnostic trouble codes displayed in the diagnostic trouble code chart. Proceed with
troubleshooting in accordance with the inspection procedures listed in the diagnostic c\
hart corresponding
to the diagnostic trouble codes displayed. The diagnostic trouble code chart for the Supplemental Restraint
System is shown below as an example.
http://vnx.su

SFISFISFISFISFISFI
D25842

Circuit Description
The major role and, operation of the circuit
and its component parts are explained.

Diagnostic Trouble Code No. and Detection Item
Indicates the diagnostic trouble codes, diagnostic
trouble code settings and suspect areas for a
problem.
Wiring Diagram
This shows a wiring diagram of the circuit.
Use this diagram together with ELECTRICAL
WIRING DIAGRAM to thoroughly understand the
circuit.
Wire colors are indicated by an alphabetical code.
B = Black, L = Blue, R = Red, BR = Brown,
LG = Light Green, V = Violet, G = Green,
O = Orange, W = White, GR = Gray, P = Pink,
Y = Yellow, SB = Sky Blue
The first letter indicates the basic wire color and
the second letter indicates the color of the stripe.
Inspection Procedures
Use the inspection procedures to determine
if the circuit is normal or abnormal. If it is ab-
normal, use it to determine whether the prob-
lem is located in the sensors, actuators, wire
harness or ECU.

Indicates the condition of the connector of the ECU
during the check.


Connections of tester are
indicated by (+), (±) after
terminals name.
Connector being checked
is connected.Connector being checked
is disconnected.
For inspection of connector
with body ground, there is
nothing about the body
ground written down.
±
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS01±31
AVENSIS REPAIR MANUAL (RM1018E)
CIRCUIT INSPECTION
How to read and use each page is shown below.
http://vnx.su

D01556
WRONG
D01563
01±16
±
INTRODUCTION REPAIR INSTRUCTION
AVENSIS REPAIR MANUAL (RM1018E)
(±) terminal cable is disconnected. If necessary, be
sure to initialize the system.
(b) HANDLING OF ELECTRONIC PARTS (1) Do not open the cover or case of the ECU unlessabsolutely necessary (If the IC terminals are
touched, the IC may be rendered inoperative by
static electricity).
(2) To disconnect electronic connectors, pull the con- nector itself, not the wires.
(3) Be careful not to drop electronic components, such as sensors or relays. If they are dropped on a hard
floor, they should be replaced and not be reused.
(4) When cleaning the engine with steam, protect the electronic components, air filter and emission±re-
lated components from water.
(5) Never use an impact wrench to remove or install temperature switches or temperature sensors.
(6) When checking the continuity at the wire connector, insert the tester probe carefully to prevent terminals
from bending.
4. REMOVAL AND INSTALLATION OF FUEL CONTROL PARTS
(a) PLACE FOR REMOVING AND INSTALLING OF FUEL SYSTEM PARTS (1) Work in a place with good air ventilation and without anything that could ca\
use combustionaround you such as a welder, grinder, drill, electric motor or stove.
(2) Never work in a place such as a pit or nearby a pit, as there is a possi\
bility that vaporized fuel will collect in those places.
(b) REMOVING AND INSTALLING OF FUEL SYSTEM PARTS (1) Prepare a fire extinguisher before starting operations.
(2) To prevent static electricity, install a ground on the fuel changer, vehicle and fuel tank, and donot spray much water so as to prevent slipping.
(3) Never use any electric equipment like an electric motor or a working lig\
ht, as they may create
sparks or a high temperature.
(4) Never use an iron hammer, as it may create sparks.
(5) Dispose of shop rags containing fuel deposits separately.
5. REMOVAL AND INSTALLATION OF ENGINE INTAKEPARTS
(a) If any metal tip is mixed in the inlet pass, this may give a bad effect to the engine and turbocharger.
(b) When removing and installing the inlet system parts,
close the opening of the removed inlet system parts and
the engine with a clean waste cloth or gum tape.
(c) When installing the inlet system parts, check that there is no mixing of a metal tip.
http://vnx.su

010B5±11
D25082
Rubber Attachment
D27697
: SUPPORT POSITION, PAN
TOGRAPH JACK POSITION
: CENTER OF VEHICLE GRAVITY
(unload condition)
: JACK POSITION
±
INTRODUCTION REPAIR INSTRUCTION
01±19
AVENSIS REPAIR MANUAL (RM1018E)
VEHICLE LIFT AND SUPPORT LOCATIONS
1. NOTICE ABOUT VEHICLE CONDITION WHEN JACKING UP
(a) As a rule, the vehicle must be unloaded when jacking up. Never jack up o\
r lift up the vehicle loaded
with things of heavy weight.
(b) When removing any parts of heavy weight like the engine and transmission, the center of gravity of the vehicle moves. Place a balance weight so as to keep it from rolling,\
or hold the jacking support
location using the mission jack.
2. NOTICE FOR USING 4 POST LIFT
(a) Follow the instruction manual for a safety operation.
(b) Do not damage tires or wheels with a free wheel beam.
(c) Using a wheel stopper, fix the vehicle.
3. NOTICE FOR USING JACK AND SAFETY STAND
(a) Work in the flat place using a wheel stopper at all times.
(b) Use a safety stand with a rubber attachment, as shownin the illustration.
(c) Support the specified location with a jack and safety stand accurately.
(d) When jacking up the front wheels, release the parking
brake and place wheel stoppers only behind the rear
wheels. When jacking up the rear wheels, place wheel
stoppers only in front of the front wheels.
(e) Do not work or leave the vehicle supported only by a jack. Be sure to support the vehicle with a safety stand.
(f) When jacking up only the front wheels or only the rear wheels, place wheel stoppers to both sides of the wheels that contact ground.
(g) When jacking down the vehicle with its front wheels jacked up, release t\
he parking brake and place wheel stoppers only in front of the rear wheels. When jacking down the v\
ehicle with its rear wheels
jacked up, place wheel stoppers only behind the front wheels.
http://vnx.su