2003 SUBARU IMPREZA trunk

Keys and doors
2-16
To arm the system using power door locking switches
1. Close all windows.
2. Remove the key from the ignition switch.
3. Open the doors and get out of the vehicle.
4. Make sure that the engine hood (and the trunk
lid) are locked.
5. Close the doors (and the rear gate on the wagon) but leave only the driver ’s door or the front passen-
ger’ s door open.
6. Push the front side ( “LOCK” side) of the power
door locking switch to set the door locks.
7. Close the door. The horn will sound one time, the parking lights will flash one time and the indicator
light will start flashing slowly (approximately once
every two seconds) to inform you that the system
has armed.
NOTE The system can be armed even if the engine hood and/or the windows are opened. Always
make sure that they are fully closed before arm- ing the system. Disarming the system
Briefly press the “UNLOCK/DISARM” button (for less
than two seconds) on the remote transmitter. The
driver’ s door will unlock, the horn will sound two
times, the parking lights will flash two times and the
indicator light will go off.
To unlock all other doors (and the rear gate on the
wagon), briefly press the “UNLOCK/DISARM” button
a second time.
Emergency disarming
If you cannot disarm the system using the transmit-
ter (i.e. the transmitter is lost, broken or the transmit-
ter battery is too weak), you can disarm the system
without using the transmitter.

Keys and doors
2-21
– CONTINUED –
The indicator light provides the following indications. Flashing one time: Any door, the rear gate or the
trunk lid has been opened.Flashing three times: The impact sensor in the sys-
tem’ s unit has been activated. This may indicate that
your vehicle has been shocked or tampered with by
some outside force and/or unauthorized person. Flashing four times: The ignition switch has been
turned on or the battery has been disconnected.
NOTE The battery must be reconnected before the indi- cator light will flash.
To exit this mode, close the door and turn the igni-
tion switch to the “ON” position. Child safety locks
1) Lock 2) Unlock
Each rear door has a child safety lock that prevents
the doors from being opened even if the inside door
handle is pulled.
When the child safety lock lever is in the lock posi-
tion, the door cannot be opened from inside regard- less of the position of the inner door handle lock
lever. The door can only be opened from the out-side.

Keys and doors
2-25
– CONTINUED –
cluster, located on the driver ’s side door, is in the
“LOCK” position, the passengers ’ windows cannot
be operated with the passengers ’ switches. Trunk lid (Sedan)
WARNING

To prevent dangerous exhaust gas from en-
tering the vehicle, always keep the trunk lid
closed while driving. Help prevent young children from locking
themselves in the trunk. When leaving the ve-
hicle, either close all windows and lock all doors or cancel the inside trunk lid release. Also make certain that the trunk is closed.
On hot or sunny days, the temperature in thetrunk could quickly become high enough to
cause death or serious heat-related injuries
including brain damage, particularly for small children.

Keys and doors
2-26
To open and close the trunk lid from outside
To open the trunk lid from outside, insert the key and
turn it clockwise.
To close the trunk lid, lightly press the trunk lid down
until the latch engages.
To open the trunk lid from inside
1) Open
Pull the trunk lid release lever upward.

Keys and doors
2-27
– CONTINUED –
To cancel the trunk lid release
The inside trunk lid release can be cancelled to help
prevent unauthorized entry into the trunk. To cancel
the trunk lid release, set the lid release cancel lever
(located on the inside of the trunk lid, mounted tothe trunk lid latch) to the “CANCEL” position. When
this lock is in the “CANCEL” position, the trunk can
be opened only with the key.
Internal trunk lid release handle
The internal trunk lid release handle is a device de-
signed to open the trunk lid from inside the trunk. In
the event children or adults become locked inside
the trunk, the handle allows them to open the lid.The handle is located on the inside of the trunk lid.
To open the trunk lid from inside the trunk, press the
yellow handle downward as indicated by the arrow on the handle.This operation unlocks the trunk lid. Then, push upthe lid.
The handle is made of material that remains lumi-
nescent for approximately an hour in the dark trunk

Keys and doors
2-28
space after it is exposed to ambient light even for a
short time.
WARNING
Never allow any child to get in the trunk and
play with the release handle. If the driverstarts the vehicle without knowing that a child
is inside the trunk and the child opens the lidusing the release handle, the child could fallout and be killed or seriously injured.
CAUTION
Do not close the lid while gripping the re-
lease handle. The handle may be damaged. Do not use the handle as a hook to fasten
straps or ropes to secure your cargo in thetrunk. Such use may result in damage of thehandle. Load the trunk so that cargo can not strike
the release handle. If the cargo hits the handlewhile the vehicle is being driven, the handle may be pushed down and the trunk lid may open. That may cause cargo to fall out of thetrunk, which could create a traffic safety haz-ard.
Inspection
Perform the following steps at least twice a year to
check the release handle for correct operation.
1. Open the trunk lid.
2. Use a screwdriver with a thin blade. Slide the
screwdriver blade from the slit aperture of the lock
assembly fully to the end until you hear a click.

Keys and doors
2-29
– CONTINUED –
This places the latch in the locked position.
3. Move the release handle, from outside the ve-
hicle, in the direction of the arrow to check if the
latch is released.
If the latch is not released, contact your SUBARU
dealer.
In that case, use the key to release the latch, then close the trunk lid.
Also, if the movements of the release handle feel re-
stricted or not entirely smooth during operation, orthe handle and/or handle base is cracked, contact
your SUBARU dealer.

Starting and operating
7-8
mination is observed, there is no stored diagnostic
trouble codes, and the OBD system readiness moni-
tors are complete. A vehicle fails
the OBD inspection if the “CHECK
ENGINE ” warning light/MIL is not properly operating
or there is one or more diagnostic trouble codes
stored in vehicle ’s computer with the “CHECK
ENGINE ” warning light/MIL illuminated.
A state emission inspection may reject (not pass
or fail) a vehicle if the number of OBD system readi- ness monitors “Not Ready ” is greater than three.
Under this condition, the vehicle operator should be instructed to drive his/her vehicle for a few days to
set the monitors and return for an emission re-in-spection. Owners of rejected or failing vehicles should con-
tact their Subaru Dealer for service. Preparing to drive
You should perform the following checks and adjust-
ments every day before you start driving.
1. Check that all windows, mirrors, and lights are
clean and unobstructed.
2. Check the appearance and condition of the tires.
Also check tires for proper inflation.
3. Look under the vehicle for any sign of leaks.
4. Check that the hood, trunk and rear gate are fullyclosed.
5. Check the adjustment of the seat.
6. Check the adjustment of the inside and outside
mirrors.
7. Fasten your seatbelt. Check that your passen-gers have fastened their seatbelts.
8. Check the operation of the warning and indicator
lights when the ignition switch is turned to the
“ON”
position.
9. Check the gauges, indicator and warning lights
after starting the engine. NOTE Engine oil, engine coolant, brake fluid, washer
fluid and other fluid levels should be checked
daily, weekly or at fuel stops.