2003 SUBARU FORESTER clock

11 - 1 0
Maintenance and service
a bad smell, smoke, and/or a fire.
If you check the oil level just after stopping the engine,
wait a few minutes for the oil to drain back into the oil
pan before checking the level.
Just after driving or while the engine is warm, the en-
gine oil level reading may be in a range between the
upper level and the notch mark. This is caused by ther-
mal expansion of the engine oil.
To prevent overfilling the engine oil, do not add any
additional oil above the upper level when the engine is
cold. Changing the oil and oil filter
Change the oil and oil filter according to the mainte-
nance schedule in the “Warranty and Maintenance
Booklet”.
The engine oil and oil filter must be changed more fre-
quently than listed in the maintenance schedule when
driving on dusty roads, when short trips are frequently
made, when towing a trailer, or when driving in ex-
tremely cold whether.
1. Warm up the engine by letting the engine idle for
about 10 minutes to ease draining the engine oil.
2. Park the vehicle on a level surface and stop the en- gine.
3. Remove the oil filler cap.
4. Open the access cover by removing the six clips
and turning the access cover counterclockwise. The
drain plug and oil filter will be exposed.
HSB025BA

11 - 1 2
Maintenance and service
result in an oil leak.
11.Close the access cover by turning it clockwise and
reinstall the six clips in their original positions.
12.Pour engine oil through the filler neck.
Oil quantity (guideline):
4.2 US qt (4.0 liters, 3.5 Imp qt)
The oil quantity indicated above is only a guideline.
The necessary quantity of oil depends on the quantity
of oil that has been drained. The quantity of drained oil
differs slightly depending on the temperature of the oil
and the time the oil is left flowing out. After pouring oil
into the engine, therefore, you must use the dipstick to
confirm that the level is correct.
13.Start the engine and make sure that no oil leaks ap-
pear around the filter’s rubber seal.
14.Run the engine until it reaches the normal operat-
ing temperature. Then stop the engine and wait a few
minutes to allow the oil drain back. Check the oil level
again and if necessary, add more engine oil.
Recommended grade and viscosity
Oil grade:
API classification SL or SJ with the words “ENER-
GY CONSERVING” (if you cannot obtain the oil
with the SL or SJ grade, you may use SH or SG
grade oil.) or the new API certification mark (Star-
burst mark) displayed on the container.
API Service label
1) Indicates the oil quality by API designations
2) Indicates the SAE oil viscosity grade
3) Indicates that the oil has fuel saving capabilities
APISERVICESL
E
NERGYCONSERVING
SAE
5W µ30
1
2
3
HSB022BB

11 - 6 0
Maintenance and service
5. Pull the headlight assembly slightly toward you,
then hold down the lock release tabs on the connec-
tors for the front turn signal light, parking light, and
front side marker light and pull out the headlight as-
sembly completely.
6. Remove the bulb socket from the headlight assem-
bly by turning it counterclockwise.
HSB079BAHSB073CA

11 -6 1
Maintenance and service
–CONTINUED –
7. Pull the bulb out of the socket. Install a new bulb.
8. Set the bulb socket into the headlight assembly and
turn it clockwise until it locks.
9. Reinstall all the removed parts by following the re-
moval sequence in reverse. Front fog light
It may be difficult to replace the bulbs. Have your
SUBARU dealer replace the bulbs if necessary. Rear combination lights
1. Remove the upper and lower screws. Then, slide
the rear combination lamp assembly to the rear and remove it from the vehicle.
HSB080BA
HSB085BA

11 - 6 2
Maintenance and service
1) Tail/stop light
2) Rear turn signal light
3) Backup light
4) Tail/stop light
2. Remove the bulb holder from the rear combination
light assembly by turning it counterclockwise.
3. Pull the bulb from the holder. Install a new bulb.
4. Set the bulb holder into the rear combination light
assembly and turn it clockwise until it locks.
5. Reinstall the rear combination light assembly.
License plate light
0
1. Remove the mounting screws using a phillipsscrewdriver.
2. Remove the cover and lens.
3. Pull the bulb out of the socket. Install a new bulb.
4. Reinstall the lens and cover.
5. Tighten the mounting screws.
3
2
1
4
HSB086BB
HSB087BA

12-8
Specifications

Fuse panel located in the engine com- partment
A) FWD socket
B) Main fuse
A 12
3 B
4
5 6
78
91011
12
HSC002BB
Fuse panelFuse ratingCircuit
120A
Radiator cooling fan (Main)
220ARadiator cooling fan (Sub)
330AABS motor
420ARear window defogger
515AHazard warning flasher
Horn
615ATurn signal lights
710AAutomatic
transmission control
unit
810AAlternator
915AHeadlight (right side)
1015AHeadlight (left side)
1120ALighting switch
1215AClock
Interior light

14-3
Index
Center console ............................................... 6-5
Charge warning light ...................................... 3-11
CHECK ENGINE warning light/Malfunction
indicator lamp ............................................. 3-10
Child restraint systems ................................... 1-30 Installation with seatbelt ............................ 1-33
Top tether anchorages .............................. 1-38
Child safety locks ........................................... 2-20
Chime Key ............................................................ 3-3
Seat belt .............................................. 1-15, 3-9
Cigarette lighter socket ................................... 6-11
Clock .............................................................. 3-16
Clutch (MT)
Fluid ........................................................... 11-31
Pedal ......................................................... 11-34
Coat hook ....................................................... 6-16
Coil tray .......................................................... 6-7
Convenience net ............................................ 6-7
Coolant ........................................................... 11-15
Cooling system ............................................... 11-14
Corrosion protection ....................................... 10-4
Cruise control ................................................. 7-31
Cruise control indicator light ........................... 3-15
Cup holders ..................................................... 6-8 D
Dashboard storage compartment ................... 6-6
Daytime running light system ......................... 3-19
Differential gear oil
Front (AT vehicles) .................................... 11-26
Rear ........................................................... 11-27
Dimensions ..................................................... 12-2
Disarming the system ..................................... 2-16
Disc brake pad wear warning indicators ......... 7-22
Dome light ...................................................... 6-2
Door locks ...................................................... 2-3
Door open warning light ................................. 3-14
Drive belt ........................................................ 11-21
Driving in foreign country ................................ 8-5
Driving tips............................................... 7-13, 8-6 E
Electronic brake force distribution (EBD) system 7-25
Emergency locking retractor (ELR) ................ 1-14
Engine Compartment overview .............................. 11-8
Exhaust gas (carbon monoxide) ................ 8-3
Hood .......................................................... 11-5
Oil .............................................................. 11-9
Coolant ...................................................... 11-15
Overheating ............................................... 9-12
Starting ...................................................... 7-9