2003 SSANGYONG MUSSO belt

M161 ENGINE MECHANICAL 1B2-29
Poly V-belt Arrangement
1 Belt Tensioning Pulley
2 Crankshaft Belt Pulley
3 A/C Compressor Pulley5 Alternator Pulley
7 Power Steering Pump Pulley
8 Water Pump Pulley

1B2-32 M161 ENGINE MECHANICAL
3. Pointed rib.
4. Belt cord visible in the base of rib.
POLY V-BELT INSPECTION

Make marks on the belt with chalk.
Rotate the engine and check the belt for damage. Notice If one of the following types of damages is found, replace the belt.
1. Rubber lumps in the base of rib.
2. Dirt or grit ingrained.

M161 ENGINE MECHANICAL 1B2-33
5. Cord torn out at the side.
6. Outer cords frayed.
7. Rib detached from the base of belt.
8. Splits across the rib.
9. Sections of rib torn out.
10. Splits across several ribs.

1B2-34 M161 ENGINE MECHANICAL
11. Splits across the back of the belt.

M161 ENGINE MECHANICAL 1B2-45
Tools Required
001 589 72 21 00 Torque Wrench
116 589 2 0 33 00 Sliding Hammer
116 589 01 34 00 Threaded Bolt Removal & Installation Procedure
1. Remove the power steering belt pulley and A/C compressorbracket.
2. Remove the oil line from power steering pump.
3. Rotate the crankshaft so that the piston of number, cylinder is at ATDC20 °
Sliding Hammer 116 589 20 33 00Threaded Pin 116 589 02 34 00
4. Put the alignment marks (arrows) on the timing chain and
camshaft sprocket.
5. Remove the chain tensioner. Installation Notice
Tightening Torque 78 - 88 Nm
6. Remove the intake and exhaust camshaft sprocket (remove the camshaft adjuster assembly in E23 engine). Installation Notice
Tightening Torque 1st step 18 - 22 Nm
2nd step 85
° - 95 °
Notice The flange bolt is designed to be used only once, so always replace with new one.
7. Remove the guide rail pin using the sliding hammer (02) and the threaded pin (03). NoticeApply the sealant on guide rail pin when installation.

1B2-46 M161 ENGINE MECHANICAL
8. Unscrew the bolts (A).Installation Notice
Tightening Torque 22.5 - 27.5 Nm
9. Remove the belt pulley and vibration damper. Installation Notice (Center Bolt)
Tightening Torque 1st step 180 - 220 Nm 2nd step 80
° - 100 °
10. Unscrew the bolts (1, 2) on timing gear case cover and
remove the timing gear case cover. Installation Notice
Tightening Torque 22.5 - 27.5 Nm
Notice Be careful not to damage the cylinder head gasket.
11. Remove the radial shaft seal
NoticeInstallation note replace the seal with new one.
12. Clean the timing gear case cover and crankcase sealing surface.
13. Replace the O-ring with new one and apply the sealant on the sealing surface.NoticeBe careful not to stain the oil chamber of chain tensioner with the sealant.
14. Installation should follow the removal precedure in the reverse order.
15. Warm up the engine and check for oil leaks.

M161 ENGINE MECHANICAL 1B2-49
BELT PULLEY AND VIBRATION DAMPER Preceding Work : Removal of cooling fan and viscous clutchRemoval of fan shroud Removal of drive belt
1 Center Bolt(M18 X 55) ....................... 1st step 200-220 Nm
2nd step 90° + 10 ° rotation added
2 Vibration Damper Disk 5 Vibration Damper Assembly
6 Key

1B2-52 M161 ENGINE MECHANICAL CRANKSHAFT FRONT RADIAL SEAL Preceding Work : Removal of belt pulley and vibration damper
1 Center Bolt (M18 x 50)............................... 1st step 200-220 Nm
2nd step 90° +10 °
2 Center Bolt Washer
3 Sleeve (Special Tool)
4 Crankshaft Front Seal
5 Key
Tools Required
601 589 03 14 00 Sleeve Replacement Procedure
1. Remove the radial seal with a screw driver.
Notice Use a clean cloth not to damage the radial seal mounting hole and the crankshaft.
5. Remove the sleeve and install the belt pulley and thevibration damper.
6. Check for leaks while operating the engine.
2. Coat the radial sealing lip with engine oil.
3. Using the sleeve, assemble the radial seal .
4. Align the sleeve groove and the woodruff key and tighten
the center bolt until the center bolt and the damper disk stop in the movement. Installation Notice
Tightening Torque 1st step 200 - 220Nm
2nd step 90
° + 10 °