2003 SSANGYONG MUSSO torque

M162 ENGINE MECHANICAL 1B1-15
30. Remove the transmission mounting bolts and separatethe transmission from the engine. Installation Notice
Tightening Torque 65 Nm
31. Remove the bolts for engine mounting bracket. Installation Notice
Tightening Torque 50 - 75 Nm
32. Hook the chain to the bracket of engine and by using a hoist or crane, carefully separate the engine assembly from the vehicle.
33. Installation should follow the removal procedure in the reverse order.

1B1-18 M162 ENGINE MECHANICAL
ALTERNATOR
1 Nut (M8)......................................... 22.5-27.5 Nm
2 Bolt (M8 x 30, 3 pieces) .................22.5-27.5 Nm
3 Bolt (M8 x 40, 1 piece) ...................22.5-27.5 Nm
Removal & Installation Procedure
1. Remove the drive belt.
2. Remove the alternator.
3. Unscrew the alternator carrier bolts and remove the carrier. Installation Notice 4 Bolt (M8 x 70, 1 piece)
...................22.5-27.5 Nm
5 Bolt (M8 x 75, 1 piece) ...................22.5-27.5 Nm
Tightening Torque 10 - 15 Nm
4. Installation should follow the removal procedure in the reverse order.

1B1-20 M162 ENGINE MECHANICAL Removal & Installation Procedure
1. Remove the belt pulley.Installation Notice
2. Disconnect the hydraulic pipe of the power steering pump and drain the oil.
3. Unscrew the bolts (arrows) and remove the steering pump. Installation Notice
Notice Pull the tensioning pulley clockwise as shown in the figure.
4. Remove the compressor after disconnecting the wiring connector and refrigerant pipe of A/C compressor. Notice Discharge all the refrigerant before removing the pipes.
Tightening Torque 40.5 - 49.5 Nm
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE MECHANICAL 1B1-21
5. Disconnect the vent hose from the A/C bracket.
6. Unscrew all the mounting bolts (arrows) and remove theA/C bracket and the gasket. Installation Notice
7. Clean the sealing surface.
8. Replace the gasket with new one.
9. Installation should follow the removal procedure in the reverse order.
10. Check the oil leakage by operating the engine after installation.
Tightening Torque 22.5 - 27.5 Nm

1B1-24 M162 ENGINE MECHANICAL
1 Upper Nut
2 Hydraulic Installor.................62-93 Nm
3 Lower Nut ............................. 28-47 Nm
Removal and Installation Procedure
1. Unscrew the upper nut(1) on engine mounting and remove the engine. Installation Notice
3. Installation should follow the removal procedure in the reverse order.
Tightening Torque 62 - 93 Nm
2. Unscrew the lower nut(3) and remove the hydraulic engine mounting insulator. Installation Notice
Tightening Torque 28 - 47 Nm
Notice If the insulator is spotted with oil, replace the hydraulic
insulator assembly.

M162 ENGINE MECHANICAL 1B1-27
TENSIONING DEVICE Preceding Work : Removal of poly v-belt
1 Belt (L = 2245)
2 Bolt Combi(M8 x 14, 3 pieces) + Washer....................................................... 22.5-27.5Nm
Removal & Installation Procedure
1. Remove the poly v-belt.
2. Remove the tensioning pulley by turning its mounting nut counter clockwise as shown in figure. Installation Notice 3 Water Pump Pulley
4 Nut
5 Tensioning Pulley
Tightening Torque 40.5 - 49.5 Nm

1B1-28 M162 ENGINE MECHANICAL
4. Remove the mounting bolts(M8 x 30, 3 pieces) at thetensioning device, and remove the tensioning device (arrow). Installation Notice
3. Remove the 3 bolts (2) and remove the water pump pulley
(arrow). Installation Notice
5. Installation should follow the removal procedure in the reverse order.
Tightening Torque 22.5 - 27.5 Nm
Tightening Torque 26 - 32 Nm

1B1-32 M162 ENGINE MECHANICAL Removal & Installation Procedure
1. Remove the intake air duct.Installation Notice
2. Remove the ignition cable cover. Installation Notice
3. Remove the spark plug connector and ignition cable.
4. Unscrew all the bolts (2,3) and remove the head cover and the gasket. Installation Notice
Notice Unscrew the seven (M6 x 60) bolts and remove the ignition
cable cover. Notice
Replace the gasket with a new one if necessary.
5. Installation should follow the removal procedure in the reverse order.
6. Check for oil leaks by operating the engine.
Tightening Torque 8 - 9 Nm
Tightening Torque 9 - 10 Nm
Tightening Torque 9 - 10 Nm