2003 SSANGYONG MUSSO cooling

1B2-22 M161 ENGINE MECHANICALPOWER STEERING PUMP AND A/C BRACKET Preceding Work : Removal of cooling fan and shroud Removal of drive belt
1 Nut ................................................. 35.2-28.8 Nm
2 Washer
3 Belt Pulley
4 Bolt (M8 X 91, 2 pieces) .................22.5-27.5 Nm
5 Power Steering Pump
6 Bracket
7 Washer
8 Bolt (M8 X 20, 2 pieces) .................22.5-27.5 Nm 9 Washer
10 Bolt (M8 X 105,4 pieces) ................22.5-27.5 Nm
11 A/C Compressor
12 Bolt (M8 X 50, 5 pieces, M8 X 80,
5 pieces) ........................................ 22.5-27.5 Nm
13 A/C Bracket
14 Vent Hose
15 Bracket Gasket ...................................... Replace

1B2-28 M161 ENGINE MECHANICAL
POLY V-BELT Preceding Work : Removal of cooling fan
1 Poly V-belt (2,155 mm)
2 Belt Tensioning Pulley
Removal & Installation Procedure
1. Release the belt tension by turning the stud on the cap with 12 sided wrench or spanner counterclockwise.
2. Remove the poly v-belt.
Notice Check the belt for damage and tensioning pulley bearing
point for wear and replace them if necessary.
3. Install the belt after prying the tensioning pulley.3 Belt Tensioner

1B2-42 M161 ENGINE MECHANICAL
10. Remove the cylinder head bolts in the reverse order ofthe numerics (No.10 No.1).
Installation Notice
Tighten the bolts as numerical order with specified torque(No.1 No.10).
Holder 104 589 00 40 00
1 Cylinder Head Bolt
2 M8 X 35 Bolt & Washer
3 Bearing Cap
4 Engine Hoist
5 Gasket
6 Hanger Bracket
Tightening Torque 1st step 55 ± 5 Nm
2nd step + 90
°
3rd step + 90 °
11. Remove the No. 1 bearing cap of the exhaust camshaft.
Installation Notice
Tightening Torque 22.5 - 27.5 Nm
12. Install the special tool (05) on the bearing cap removed place and hook the engine hoist into them and remove
the cylinder head carefully.
13. Check the cylinder head mating surface and clean the crankcase head bolt mounting hole.
14. Replace the cylind head gasket with new one. Notice Operate during engine cooling.

M161 ENGINE MECHANICAL 1B2-49
BELT PULLEY AND VIBRATION DAMPER Preceding Work : Removal of cooling fan and viscous clutchRemoval of fan shroud Removal of drive belt
1 Center Bolt(M18 X 55) ....................... 1st step 200-220 Nm
2nd step 90° + 10 ° rotation added
2 Vibration Damper Disk 5 Vibration Damper Assembly
6 Key

1B3-2 OM600 ENGINE MECHANICALSPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
N

 m
28 - 47 30
3 - 7
8 - 18
20 - 34 30
70 - 80 81 - 8450 - 75
N 

 m
10 23
200 / 90 °
10
55 / 90 °
45 / 90 °
25 / 90 °
25
N 

 m
35 / 90 °
N 

 m
45 / 90 °
Application
Skid Plate Bolt Drain Plug Bolt Coolong Fan Shroud BoltControl Linkage NutClutch Linkage Cylinder NutExhaust Manifold Bolt
Propeller Shaft Bolt & Nut (Axle) Propeller Shaft Bolt & Nut (T/C)
Engine Mounting Nut
Application
Cooling Fan Belt Pulley Bolt Socket Bolt
Tighten The BoltEnd Cover BoltCrankshaft Bearing Cap Bolt Ball Bearing Camshaft Sprocket BoltOil Pump Sprocket Bolt
Application
Connecting Rod Bolt
Application
12-Sided Stretch Bolt
Engine Assembly
Crankshaft Assembly Piston
Flywheel
Cylinder Head
Application
Prechamber Threaded Ring Cylinder Head Cover Bolt Fuel Injsction Pipe NutSocket BoltFuel Filter Pipe BoltIdle Pulley Bolt Damper Bolt N


 m
130 10 18252523 21

OM600 ENGINE MECHANICAL 1B3-9
601 589 02 23 00
Go/No Go Gauge
105 589 03 15 00 Drift (for Intake) 601 589 06 15 00
Drift (for Exhaust)
SPECIAL TOOLS TABLE (Co n t
’d)
601 589 05 15 00
Drift (for Intake)
103 589 02 15 00
Drift (for Exhaust)
346 589 00 63 00
Super Cooling Box 000 589 21 53 00
Reamer (for Intake) 000 589 10 53 00
Reamer (for Exhaust)

1B3-14 OM600 ENGINE MECHANICAL9. Loosen the bolt and remove the coolant pipe and cooling fan shroud.
10. Remove the hoses (air intake to intercooler, intercooler to intake duct).
8. Disconnect the upper coolant hose from the radiator.
Tightening Torque 3 -7 Nm
11. Remove the pipes connected to intercooler.

OM600 ENGINE MECHANICAL 1B3-23
TENSIONING DEVICE Preceding Work : Removal of cooling fan
1 Bolt............................................................ 21Nm
2 Damper
3 Nut ............................................................. 21Nm
4 Tensioning Lever
5 Guide Rail Pin
6 Bolt
7 Poly V-Belt
8 Belt Pulley
9 Bolt ............................................................ 10Nm10 Tensioning Pulley
11 Socket Bolt ................................................ 29Nm
12 Closing Cover
13 Washer
14 Tensioning Lever
15 Fit Bolt ..................................................... 100Nm
16 Closing Cover
17 Spring
18 Bolt ............................................................ 20Nm