2003 SSANGYONG MUSSO engine oil

OM600 ENGINE MECHANICAL 1B3-63
TIMING CASE COVER
Preceding Work : Removal of the cooling fanRmoval of the V-belt tensioning device Removal of the vibration damper and hub Removal of the alternator
1 Bolt............................................................ 10Nm
2 Cylinder Head Cover
3 Gasket ................................................... Replace
4 Socket Bolt ................................................ 25Nm
5 Fuel Filter
6 Square Nut
7 Oil Pan
8 Socket Bolt ................................................ 10Nm
9 Bolt .................................................... M6 : 10Nm
M8 : 23Nm 10 Power Steering Pump
11 Bolt
12 Belt Pulley 13 Bolt
............................................................ 32Nm
14 Timing Case Cover
15 Bolt ............................................................ 23Nm
16 Alternator Bracket
17 Bolt ............................................................ 45Nm
18 Bolt ............................................................ 25Nm
19 Bolt ............................................................ 10Nm
20 Closing Cover
21 Socket Bolt ................................................ 23Nm
22 Guide Pulley
23 Bolt .............................................................. 9Nm
24 Guide Pulley Bracket
25 Nut ............................................................. 23Nm

1B3-64 OM600 ENGINE MECHANICAL
8. Remove the guide pulley bracket (24).
Tools Required
116 589 03 07 00 Socket Wrench Removal Procedure
1. Remove the fan clutch and cooling fan belt pulley.
2. Drain the engine oil completely.
3. Remove the oil dipstick tube bracket bolts.
4. Remove the crankshaft pulley.
5. Loosen the bolt (1) and then remove the cylinder head cover(2) and gasket.
6. Remove the vacuum pump.
7. Detach the closing cover (20). Remove the bolts(21) and then remove the guide pulley (22).

1B3-66 OM600 ENGINE MECHANICAL
18. Remove the timing case cover (19) bolts and then removethe timing case cover (14). Notice Be careful not to damage the cylinder head gasket or oil pan gasket.
13. Remove the camshaft.
14. Remove the socket bolts(4) in the chain box.
Socket Wrench 115 589 03 07 00
15. Remove the injection pump. NoticeSee the ‘Removal of fuel injection pump ’.
16. Remove the oil pan bolts (8, 9) in the area of the timing case cover (14).
17. Slightly loosen the remaining oil pan bolts.

OM600 ENGINE MECHANICAL 1B3-67
Installation Procedure
1. Thoroughly clean the sealing surface and apply sealant.
2. Install the timing case cover.Notice Bolts arrangement
1.M6 x 60
2.M6 x 70
3.M6 x 40
3. Tighten the socket bolts in the chain box.
Tightening Torque 10 Nm
Tightening Torque 23 Nm
4. Tighten the oil pan bolts.
Tightening Torque 10 Nm 10 Nm23 Nm
Socket bolt
M6 bolt M8 bolt

1B3-70 OM600 ENGINE MECHANICAL
15. Install the guide pulley (22) and fit the closing cover (20).
16. Replace the gasket (3) and install the cylinder head cover(2).
17. Install the cooling fan belt pulley and fan clutch.
18. Install the belt tensioning device and then install the belt.
19. Install the cooling fan.
20. Fill the engine oil and check oil leaks by running the engine.
Tightening Torque 23 Nm
Tightening Torque 10 Nm

1B3-72 OM600 ENGINE MECHANICAL
Tools Required 601 589 03 43 00 Oil Seal Assmbler Removal Procedure
1. Remove the bolts (3, 6) from end cover, By pulling out thelugs (arrow), remove the cover. Notice Be careful not to damage the oil pan gasket.
2. Remove the radial seal (4) with care not to damage the sealing surface.
Installation Procedure
1. Thoroughly clean the sealing surface of end cover and applyLoctite 573.
2. Clean the groove of radial seal.
3. Apply Loctite 573 on the bolts and install the end cover.
Tightening Torque 10 Nm
Notice Be careful not to damage the oil pan gasket.
4. Install the inner oil seal assembler to the crankshaft flange.
Oil Seal Assembler 601 589 03 43 00

OM600 ENGINE MECHANICAL 1B3-73
Notice The sealing lip of the repair radial seal is offset to the inside by 3mm to ensure that it does not run in any groove whichthe standard radial seal may have left on the crankshaftflange.
7. Install the outer oil seal assembler on he seal and by tightening the bolts, press the radial seal into the end coveras far as the stop. Notice The seal must be positioned exactly at right angles in the end cover to ensure that it provides a proper seal.
Oil Seal Assembler 601 589 03 43 00 A Standard Radial Seal
B Repair Radial Seal
5. Coat a little oil on the sealing lip of new radial seal and
contacting surface. Notice Don ’t use grease.
6. Insert the new radial seal (4) onto the oil seal assembler (7).

1B3-74 OM600 ENGINE MECHANICAL
VIBRATION DAMPER AND HUB
Preceding Work : Removal of the cooling fanRemoval of poly V-belt
1 Bolt............................................................ 10Nm
2 Cooling Fan Belt Pulley
3 Socket Bolt ................................................ 23Nm
4 Crankshaft Belt Pulley
5 Vibration Damper 6 Bolt
................................................ 200Nm + 90 °
7 Washer
8 Straight Pin
9 Hub
10 Oil Pan