2003 SSANGYONG MUSSO brake sensor

2A-6 SUSPENSION DIAGNOSIS DAMPING FORCE CONTROL LOGIC Control Logic that applies on damping force variable suspension is comprised of road sensing driving comfort control logic to increase driving comfort and vehicle speed sensing control logic, anti-roll control logic and anti-dive control
logic to secure control safety.
LogicSensor
Road Sensing Driving Comfort Control LogicSpeedVertical
Sensor (2.5g)Lateral
Sensor (1g)Axle
Acceleration
Sensor (10g) Brake
Anti-bounce Control Logic Anti-roll Control LogicAnti-dive Control Logic
Vehicle Speed Sensing Control Logic
NORMAL CONTROL Initial Stage When ignition switch is "ON", system initialization will be performed for approx. 3 seconds. During this time, warning lamp will stay ON and damping force will be switched to Hard status. After 3 seconds, warning lamp will turn off and normal control status will be restored. Normal Damping Force Control Establishment Damping force will have Soft Medium Hard status in AUTO mode and Medium Hard status in SPORT mode.
When double control items are satisfied at the same time it will be Hard Medium Soft in order.
Normal Damping Force Control Release Control mode release will be "Hard Medium Soft"or "Medium Soft". In case that returned from Hard status to
Medium status during control, it will be done after elapse of setting times. Returning from Medium status to Soft status
will be done immediately without delay.

SUSPENSION DIAGNOSIS 2A-11
Connector Pin Number and Circuits
2
15
3
16
4
17
5
18
6
19
7
20
8
21
9
22
10
23
11
24
12
25
13
26
Ignition
Actuator R-MEDIUM Actuator R-SOFT
Actuator F-HEAD Select Switch
Speed Sensor
Wheel G Sensor
Wheel G Sensor Ground
-
Vertical G Sensor
Sensor +5V
Chassis Ground Indicator Lamp
NO. CircuitNO. Circuit
1 14
21 5
316
417
518
619
720
821
922
10 23
11 2 4
12 25
13 26 Chassis Ground
Actuator R-HEAD
Actuator F-MEDIUM
Actuator F-SOFT Brake Switch
-
Lateral G Sensor
Lateral G Sensor Ground
Vertical G Sensor Ground Diagnosis K Line
Diagnosis L Line - -

FRONT DRIVE AXLE 3A-9
Removal & Installation Procedure
1. Remove the tire.Installation Notice
Steel Wheel
Aluminum Wheel
Tightening Torque80 - 120 Nm
110 - 130 Nm
2. Remove the autolocking hub vacuum hose.
3. With ABS Remove the wheel speed sensor from the steering knuckle. Installation Notice
4. Remove the mounting bolts and pull off the caliper assembly. Installation Notice
Tightening Torque 6 - 8 Nm
Hose Bolt
Mounting Bolt
Tightening Torque25 - 35 Nm
85 - 105 Nm
Notice Be careful not to damage the brake hose.

SECTION 4A
HYDRAULIC BRAKES
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4A-1
General Specifications . . . . . . . . . . . . . . . . . . 4A-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Noise or Vehicle Vibration When Applied
Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Pulls to One Side When Braking . . . . . . . . . . . 4A-2
Poor Braking . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2Increasing Pedal Stroke (Pedal Goes to
Floor) or Brake Dragging . . . . . . . . . . . . . . . 4A-3
Poor Braking of Parking Brake . . . . . . . . . . . . 4A-3 TABLE OF CONTENTS
Component Locator . . . . . . . . . . . . . . . . . . . 4A-4
ABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-4
ABS / ABD . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-5
Non-ABS / ABD . . . . . . . . . . . . . . . . . . . . . . . . 4A-6
Maintenance and Repair . . . . . . . . . . . . . . . 4A-7
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 4A-7
Bleeding the Brakes . . . . . . . . . . . . . . . . . . . . 4A-7
Brake Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-9
LCRV (Load Conscious Reducing Valve) . . . 4A-12
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting thiscable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCKunless otherwise noted.
Type
Pedal Ratio
Pedal Stroke
Pedal Freeplay Type
Inner Diameter Type
Ratio
Type
I.D. of Caliper Cylinder
Thickness of Brake Pad Thickness of Disc Plate Type
I.D. of Caliper Cylinder
Thickness of Brake Pad Thickness of Disc Plate
Type
Operation
Specification PBR Brake
4.3 : 1
132 mm
23.81 mm
5.0 : 1
60.4 mm

40.5 mm
9.5 mm

Suspended
1 - 4 mm
Tandem Type with Lever Sensor
Vacuum Booster Type
Ventilated Disc 10 mm 24 mm
Rear Wheel Internal Expansion Type Mechanical
SAE J1703, DOT3
SPECIFICATIONS
GENERAL SPECIFICATIONS
Brake Pedal
Master Cylinder Brake Booster Front Brake
Rear Brake
Parking Brake Brake Fluid MANDO Brake
4.3 : 1
138 mm
25.4 mm
5.6 : 1
60 mm
Solid Disc
38.2 mm
10.0 mm 10.4 mm
Application

HYDRAULIC BRAKES 4A-13
Construction LCRV consists of sensing part and hydraulic control part.
1. Sensing PartIt detects the changes of vehicle height caused by vehicle load. It consists of load sensing spring and control leverwhich change according to vehicle load.
2. Hydraulic Control Part It consists of valve stem devices which controls hydraulicpressure according to load detected by sensing part.
Trouble Shooting Poor Braking Possible Cause
Air in Brake System Poor Adjustment of Sensor SpringDamaged Sensor SpringFluid Leaking from LCRV Remedy
Bleeding Adjust
Replace Replace
Possible Cause
Poor Adjustment of Sensor Spring Internal Fluid Leaking of LCRV Remedy
Adjust
Replace
Abnormal Locking

4B-2 MASTER CYLINDER
1 Nut .......................................................14-22 Nm
2 Washer
3 Master Cylinder Assembly
4 Oil Level Sensor
5 Check V alve
6 Booster
7 Clevis Pin
8 Snap Pin9 Seal
10 Spacer 11 Nut ......................................................... 8-18 Nm
12 Front Tube (LH)
13 Front Tube (RH)
14 Rear Tube
15 1st Tube (Primary)
16 2nd Tube (Secondary)
MANDO
PBR
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
BOOSTER AND BRAKE MASTER CYLINDER

MASTER CYLINDER 4B-3
Removal & Installation Procedure
1. Remove the oil level sensor connector.
2. Remove the tube from the master cylinder.Installation Notice Notice
Be careful not to drop the oil when removing the tube.
If the oil is dropped, promptly sweep up.
3. Remove the booster vacuum hose. Notice
Connect fully to the end of vacuum hose when installing.
4. Loosen the nut of master cylinder. Installation Notice
5. Remove the clevis pin and disconnect the pedal and brake booster push rod. Notice
Install in the upper hole when PBR brake.
Connect the snap pin in the hole of clevis pin fully.
Apply the grease around the hole of clevis pin.
Tightening Torque 14 - 22 Nm
Tightening Torque 15 - 19 Nm

4C-2 POWER BOOSTER
1 Nut .......................................................14-22 Nm
2 Washer
3 Master Cylinder Assembly
4 Oil Level Sensor
5 Check V alve
6 Booster
7 Clevis Pin
8 Snap Pin MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
BOOSTER AND BRAKE MASTER CYLINDER9 Seal
10 Spacer 11 Nut ......................................................... 8-18 Nm
12 Front Tube (LH)
13 Front Tube (RH)
14 Rear Tube
15 1st Tube (Primary)
16 2nd Tube (Secondary)
MANDO
PBR