2003 SKODA FABIA Owner's Manual

Fuses and light bulbs
216
– Insert the lamp holder with new light bulb into of the headlight.
Low beam
– Open the bonnet.
– Remove the protective cover at the rear of the headlight ⇒page 214, fig. 153 .
– Unplug plug .
– Unlock the sprung wire clamp downwards and swing to the side.
– Remove the light bulb and insert the new light bulb in such a way that the fixing lug on the reflector lies in the corre-
sponding recess in the lamp plate. – Close the sprung wire clamp over the plate and engage it
again.
– Plug in plug .
– Get the headlight setting checked by a Skoda dealer after replacing the light bulb.
Turn signal light (at the front)
– Open the bonnet.
– Screw out the lamp holder and light bulb by turning it anti-clockwise ⇒fig. 158 .
– Press the defect light bulb in to the holder, turn anti-clockwise and remove.
Fig. 157 Structure of
the light bulb of the low
beam light
AA
AB
A1
AA
Fig. 158 Structure of
the light bulb of the
turn signal light

Fuses and light bulbs217
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assist-
anceTechnical DataFabia Praktik
– Insert the new light bulb and turn it fully to the right.
– Insert the lamp holder with new light bulb into the headlight.
Secure the lamp holder by turning it to the right.
Fog lights*
We recommend having the light bulb replaced by a Škoda dealer.
– Remove the protective grille next to the light.
– Unscrew the screws on the fog light holder. The upper screw holds the outer air temperature sensor* in place on the light
⇒fig. 159
– Remove the end cover of the light.
– Disconnect plug connector ⇒fig. 160 .
– Press together the sprung wire clamp on the lamp holder and swing down.
– Remove the light bulb with cable.
– Insert the new halogen lamp in such a way that the fixing lug on the reflector lies in the corresponding recess in the lamp
plate.
Fig. 159 Removing the
fog light
Fig. 160 Structure of
the light bulb of the fog
light
A1
AB
AA

Fuses and light bulbs
218
– Close the sprung wire clamp over the lamp plate. Press together the sprung wire clamp and lock together again.
– Plug into the plug connector .
Note
One should ensure that the outer air temperature sensor* is in the
correct position when mounting the fog light.
Lighting in storage compartment on front passenger
side*
We recommend having the light bulb replaced by a Škoda dealer. – Push in a knife or screwdriver from the side between the light
and the glove compartment ⇒fig. 161 . Lever out the light
carefully.
– Disconnect the plug by pressing the catch from the side.
– Replace the defect light bulb.
– Recreate the plug connection.
– Press the light into the glove compartment from below.
Interior light and the reading light*
– Pull the diffusion disk (see arrow) downwards from the housing ⇒fig. 162 .
AA
AB
A1
Fig. 161 Remove
lighting in storage
compartment on front
passenger side
Fig. 162 Remove inte-
rior light

Fuses and light bulbs219
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assist-
anceTechnical DataFabia Praktik
– Take the faulty light bulb out of the interior light and insert a
new one.
– Pull the light bulb out of its holder and insert the new one.
– Press the diffusion disk back into the housing until it clicks into
place (ensure that it is in the right position).
Licence plate light
– Open the tailgate and screw off the light glass.
– Take the faulty bulb out of the fixture and insert a new one.
– Re-insert the light glass. Press the light glass in up to the stop - check for correct seating of the sealing rubber.
– Screw on the light glass but not too tightly.
Front door warning light*
We recommend having the light bulb replaced by a Škoda dealer.
– Push in a knife or screwdriver from the side between the light and the door panel ⇒fig. 164 . Lever out the light carefully.
– Disconnect the plug connector.
– Replace the defect light bulb.
– Recreate the plug connection.
– Insert the door warning light into the door panel from the plug side and press in.
Fig. 163 Remove the
licence plate light
Fig. 164 Remove the
front door warning light

Fuses and light bulbs
220
Rear light unit
– Open the boot lid/luggage compartment door.
– Push the cover to the side carefully.
– Press the fixing straps in the upper part of the light bulb holder
in the direction of the arrow and remove the light bulb holder
⇒fig. 165 .
– Press the defect light bulb in to the holder, turn anti-clockwise and remove.
– Insert the new light bulb and turn it fully to the right.
– Insert the light bulb holder into the opening of the rear light from below and interlock the fixing straps into the upper part.
– Push the cover back into place.
Rear light unit (estate car, sedan)
– Open the boot lid/luggage compartment door.
– Remove the cover in the boot.
– Press the catch in direction of arrow and pull out the light bulb holder.
– Press the defect light bulb in to the holder, turn anti-clockwise and remove.
– Insert the new light bulb and turn it fully to the right.
– Insert the light bulb holder again, the plastic tongue must lock in place.
– Install the cover in the boot.
Fig. 165 Remove light
bulb holderFig. 166 Remove the
light bulb holder
(estate car, sedan)

Fuses and light bulbs221
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assist-
anceTechnical DataFabia Praktik
Luggage compartment light
– Open the tailgate and remove the luggage compartment
cover.
– Insert a screwdriver into the slot next to the light ⇒fig. 167 .
Lever out the light carefully.
– Disconnect the plug connector.
– Replace the defect light bulb.
– Recreate the plug connection.
– Insert the light from the rear and press it forwards up to the stop.
Boot light (sedan)
– Insert a screwdriver into the slot under the light ⇒fig. 168 .
Lever out the light carefully.
– Unlock the lug then pull out the plug.
– Push away the spring clip on the cover and remove the cover.
– Replace the defect light bulb.
– Insert the cover again and secure it by locking it in place.
– Recreate the plug connection.
– Insert the light from the rear and press it forwards up to the stop.
Fig. 167 Remove the
luggage compartment
lightFig. 168 Remove the
boot light (sedan)
A1
A2

Fuses and light bulbs
222

General223
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assist-
anceTechnical DataFabia Praktik
Technical Data
General
Identification data
Vehicle data sticker
The vehicle data sticker ⇒fig. 169 is located on the floor of the luggage
compartment and is also stated in the Service Schedule.
The vehicle data sticker contains the following vehicle data:
Vehicle identification number
Vehicle type
Gearbox code, paint number, interior equipment number, engine
output, engine code
Optional equipment Vehicle identification number (vehicle body number)
The vehicle identification number is stamped into the engine compartment
on the right hand shock absorber dome. This number is also located on
the lower left hand edge below the windscreen.
Engine number
The engine number is stamped into the engine block.
Ty p e p l at e
The type plate is located in the engine compartment at the front on the left
hand shock absorber dome. Vehicles for certain countries do not have a
type plate.
Homologation sign
The homologation sign is located on the lock carrier. Vehicles for certain
countries do not have an homologation sign.
Stickers on inside of fuel filler flap
The stickers are affixed to the inside of the fuel filler flap
⇒page 169. The
vehicle data sticker contains the following data:
•The prescribed types of fuel
•Tyre size
•Tyre pressure
Note
•You will find the technical data of your vehicle in the separate brochure
"Technical Data".
Fig. 169 Vehicle data
sticker
A1
A2
A3
A4