
The  HUD  also  shows the following lights when they  are 
lit  on  the  instrument panel  cluster: 
Turn Signal Indicators 
High-Beam  Indicator Symbol 
Low Fuel  Symbol 
The  HUD  will display  CHECK  GAGES  when  the 
following  items are lit  on  the instrument panel cluster: 
Oil Warning  Symbol 
Coolant  Temperature  Symbol 
Charging  System  Symbol 
When  the  ignition key  is turned to  RUN, the entire  HUD 
image  will come  on.  Then  the Head-Up  Display will 
operate normally. 
Notice: Although  the HUD image  appears  to be 
near  the front 
of the  vehicle,  do not use it as 
a  parking  aid. The 
HUD was  not  designed for  that 
purpose. 
If you  try  to  use it as such,  you may 
misjudge  the  distance  and  damage your  vehicle. 
When the HUD  is on,  the  speedometer  reading will be 
displayed  continually.  The current radio station 
or 
CD track  number will only be displayed  for three 
seconds  after the  radio  or  CD track status  changes. 
This will  happen  whenever  one  of the  radio controls is 
pressed, either  on the  radio itself  or on  the optional 
steering  wheel controls.  To 
adjust  the  HUD 
so you  can see it properly  do  the 
following: 
1. Adjust  your seat, if necessary,  to a comfortable 
position. 
2. Start the engine  and  adjust  the  HUD  controls 
located  on the  instrument  panel, to the  right 
of 
the  steering wheel.  Move  the  DIM  thumbwheel  up 
or down to adjust  brightness. 
3-1 6  

The  Driver  Information  Center  (DIC)  gives you important 
safety  and maintenance  facts. When  you turn the 
ignition  on, all of the  DIC  lights illuminate for  a  few 
seconds.  After  this,  the  DIC will begin working. 
Functions 
__ (Door  Ajar): If  one  of the doors is ajar, this  light 
will  appear  next  to  that  door  on  the vehicle  outline. 
CHANGE OIL SOON: This light  will appear when the 
system  indicates  that  it’s  time for  an  oil change. The 
system  predicts  remaining  oil  life using data from  length 
of  drives,  coolant  temperature,  engine  rpm  and 
vehicle  speed.  It alerts  you  to change the  oil  on a 
schedule  consistent  with  the vehicle’s driving conditions. 
After  changing  the oil,  the  system  must be reset.  See 
How  to  Reset  the  GM 
Oil Life  SystemTM  under 
Engine 
Oil on  page 5- 18. 
e LOW: This  light  will  come on when the  ignition is 
on  and  the  fluid in  the  washer  fluid container is low. 
AJAR: This  light alerts you that the trunk  is not 
fully  closed. 
LOW TRAC  (Low  Traction): If your vehicle  is equipped 
with  anti-lock brakes, this  light  will come on when  the 
enhanced traction system is limiting wheel spin.  See  Enhanced Traction System (ETS) on  page 4- 
I I or 
Low Traction Light on page 3-30. 
TRAC OFF (Traction  Off): If your vehicle  is equipped 
with  anti-lock brakes, this  light lets you know that 
the enhanced traction  system has been disabled  and 
will  not limit wheel  spin.  See  Enhanced  Traction System 
Warning Light 
on page 3-30  or Low  Traction Light on 
page 3-30. 
TRAC (Traction): If the vehicle has anti-lock brakes 
and the  enhanced traction  system, you will  have  a 
disable button  on the  far  right  side  of the  DIC. 
The enhanced traction  system is automatically activated 
when  you turn the  ignition  on. This button will 
activate/deactivate the  system. If you  need to  disable 
the system, such 
as when  you  are stuck  and are  rocking 
the vehicle back and  forth,  push this button.  See  If 
You Are  Stuck: in Sand, Mud, Ice or Snow  on 
page 4-32. 
3-39  

Control Buttons 
The trip computer  has three  buttons that control  its 
functions. 
ENG/MET  (English/Metric): Press this  button  to 
change  the display from  English 
to metric units or  metric 
to English. 
RESET: Press this  button  for  two  seconds to reset the 
mode displayed. 
MODE: Press this  button  to change  the function  mode, 
(Fuel  Used,  AVG  ECON,  OIL LIFE,  RANGE)  being 
displayed. 
OIL LIFE: This  shows  a  percentage of the  engine’s  oil 
remaining useful life.  The  system  predicts  remaining 
oil  life using data from length  of drives,  coolant 
temperature, engine  rpm  and vehicle speed.  Each  time 
you get  an oil change,  be sure to reset  this  function 
so that  it will give  you  an accurate  percentage.  See 
“How to Reset  the GM Oil Life  System”  under  Engine 
Oil  on page 
5-18. 
RANGE: This  mode  shows  how  much  farther  you  can 
travel with the fuel  you  have remaining in  the  gas 
tank  before refueling.  When  the range displays 
L, for 
40  to 
50 miles  (64.36 to 80.45 km), the  display will flash 
LOW continuously.  The range  is calculated  from  the 
AVG  ECON  value multiplied by the fuel  remaining in 
the tank. 
Functions 
LOW: This  light will  come  on  the  vehicle  outline  when 
FUEL USED: This mode  shows  the total amount of fuel the  ignition  is on  and  the  fluid  in the  washer  fluid 
used  since  you last reset  it.  The  amount  can be  container is low. 
displayed  in gallons  or liters. 
AVG  ECON  (Average  Economy): This mode  shows 
the  average  fuel economy  since you last reset 
it. 
3-42  

I- 
3100 . - Engine 
A 
A 
* 
SAE 1OW-30 
m 
I 
3800 V6 or 3800 V6 
Supercharged  Engine 
The  engine oil fill cap will have  one  of these  symbols  on 
it,  depending  on  the engine. It is located  on the  front 
of  the  engine, near the center  of the engine 
compartment  and  the yellow-looped engine oil dipstick. 
See  Engine  Compartment Overview  on  page 
5-12 
for  more information on location. 
Be  sure  to 
fill it  enough  to  put the level  somewhere 
in  the  proper operating range  in the cross-hatched area. 
Push  the dipstick 
all the way  back  in when  you're 
through. 
What Kind of Engine  Oil to Use 
Oils  recommended  for  your  vehicle can be identified  by 
looking  for the starburst symbol. 
This  symbol  indicates  that  the oil has  been  certified by 
the  American  Petroleum Institute  (API). 
Do not  use 
any  oil which  does  not carry this  starburst  symbol. 
If  you  choose  to perform 
the  engine  oil change 
service  yourself,  be  sure 
the oil  you  use  has 
the  starburst  symbol  on 
the front  of the  oil 
container.  If  you  have  your 
oil  changed  for  you,  be 
sure  the  oil  put  into 
your  engine  is  American  Petroleum Institute certified 
for  gasoline  engines. 
You  should also  use  the proper viscosity  oil  for  your 
vehicle, as  shown in the  viscosity  chart. 
5-20  

RECOMMENDED SAE VISCOSITY GRADE ENGINE OILS 
HOT 
WEATHER 
COLD 
SAE S’W. 
LOOK 
FOR THIS 
SYMBOL 
. 
1-11 SAE IOW-30 ACCEPTABLE r IF 5W-30 IS NOT -30 AVAILABLE 
RECOMMENDED 
WEATHER 
DO NOT USE SAE 1OW-40, SAE 2OW-50 OR ANY OTHER VlSCOSlN GRADE OIL NOT RECOMMENDED 
As  in the chart  shown previously, if you  have  the 
3100  V6  engine, SAE  5W-30  is the only viscosity  grade 
recommended  for  your vehicle. You should look for 
and  use only oils  which  have  the  API  Starburst symbol 
and  which  are also  identified  as 
SA€ 5W-30. If you 
cannot find such  SAE  5W-30  oils,  you  can use an 
SAE  IOW-30 oil  which has the API  Starburst symbol, 
if it’s going  to be 0°F (-18°C)  or  above. Do not use 
other viscosity  grade oils, such  as SAE  IOW-40 
or  SAE  20W-50  under  any  conditions. 
As  shown  in the following chart, 
if you  have  the 
3800  V6  engine, SAE IOW-30 is  the viscosity  grade 
recommended  for your vehicle.  However,  you  can  use 
SAE 5W-30 if it’s going to be  colder than  60°F  (16°C) 
before your next 
oil change.  When it is  very cold, colder 
than  0°F 
(-1 8°C)  you should  use  an  SAE  5W-30 oil. 
These  numbers  on  an oil container  show its viscosity, 
or  thickness. 
Do not  use  other viscosity  grade  oils, 
such  as SAE  1 
OW-40 or  SAE  20W-50  under  any 
conditions. 
3100 V6 Engine 
5-2 1  

When to Change Engine Oil (GM Oil 
Life SystemTM) 
Your  vehicle  has  a computer  system  that lets you  know 
when  to  change  the  engine 
oil and filter.  This is 
based  on  engine  revolutions  and engine  temperature, 
and  not  on  mileage.  Based  on  driving  conditions, 
the  mileage  at  which  an  oil  change will  be indicated 
can  vary  considerably.  For  the  oil  life system  to 
work  properly,  you  must  reset  the  system  every  time 
the  oil  is changed. 
When  the  system  has  calculated  that oil  life  has  been 
diminished,  it  will  indicate  that an  oil  change is 
necessary. 
A CHANGE  OIL SOON  light  will  come on. 
Change  your 
oil as  soon  as possible  within  the  next  two 
times  you  stop  for  fuel. 
It is possible  that, if you are 
driving  under  the  best  conditions,  the  oil  life  system  may 
not  indicate  that  an  oil  change is  necessary  for  over  a 
year.  However,  your  engine  oil  and filter  must  be 
changed  at  least  once  a year  and at this  time  the  system 
must  be  reset.  It is  also  important  to  check your oil 
regularly  and  keep  it  at  the  proper level. 
If the  system  is  ever  reset  accidentally,  you  must 
change  your  oil  at 
3,000 miles (5 000 km)  since  your 
last  oil  change.  Remember 
to reset  the  oil  life system 
whenever  the  oil  is  changed. 
How to  Reset the GM Oil Life System 
The  GM Oil Life  SystemTM  calculates  when to change 
your  engine  oil and filter  based  on  vehicle  use.  Anytime 
your  oil is  changed,  reset  the system 
so it can  calculate 
when  the next  oil change is  required. 
If a situation occurs 
where  you change  your  oil prior to a CHANGE 
OIL SOON 
light  being turned  on,  reset the system. 
To  reset  the GM  Oil Life  SystemTM  after the oil has 
been  changed,  use  one of the  following  two procedures: 
Using the  Driver  Information  Center  (DIC) 
1. 
2. 
3. 
With the  ignition  key in RUN  but  the  engine off, fully 
push  and release  the  accelerator  pedal slowly three 
times  within  five  seconds. 
If the  CHANGE  OIL SOON light flashes, the  system 
is  resetting. 
Turn  the  key  to OFF  after  the  light stops  flashing, 
then  start  the  vehicle. 
If the CHANGE OIL SOON light comes  back on, the 
engine  oil  life monitor  has  not  reset.  Repeat the 
procedure. 
Using  the Trip Computer  (If  Equipped) 
1. Press the MODE button until  the  light appears  lit 
2. Press and hold the RESET  button for three  seconds. 
next to 
OIL LIFE. 
The 
oil life  percentage  should change to 100%. 
5-23  

What to Do with Used Oil 
Used engine oil contains certain  elements that may  be 
unhealthy  for your skin  and could  even  cause  cancer. 
Don't  let  used oil stay  on your skin for very  long.  Clean 
your  skin and nails with  soap  and water, or a  good 
hand cleaner.  Wash or  properly dispose  of clothing  or 
rags containing  used engine oil.  See the  manufacturer's 
warnings  about the  use  and  disposal of oil products. 
Used  oil can  be  a threat to the environment.  If  you 
change your  own oil, be sure  to drain  all the oil from the 
filter  before disposal.  Never dispose  of oil  by  putting it 
in the  trash, pouring  it on  the ground, into sewers, or into 
streams  or  bodies of water.  Instead, recycle  it by 
taking 
it to  a place that collects  used oil. If you  have  a 
problem  properly disposing  of your  used  oil, ask 
your  dealer, a service station  or  a local recycling 
center for  help. 
Supercharger Oil 
Unless you are technically 
qualified  and  have  the 
proper tools,  you should  let 
your  dealer  or  a qualified 
service  center  perform 
this  maintenance. 
When  to Check 
Check  oil level every 30,000 miles (50 000 km)  or  every 
36 months,  whichever  occurs  first. 
What Kind of Oil to Use 
Use only  the recommended  supercharger  oil.  See Part 
D: Recommended  Fluids and Lubricants on page 6-15. 
5-24  

Automatic  Transaxle  Fluid 
When to Check and Change 
A good time to  check  your  automatic transaxle fluid 
level is  when  the  engine  oil is changed. 
Change  both the fluid  and filter  every  50,000 miles 
(83 
000 km) if the  vehicle  is mainly driven  under  one  or 
more  of these  conditions: 
In heavy  city traffic  where  the  outside temperature 
0 In hilly or  mountainous  terrain. 
0 When doing frequent  trailer towing. 
0 Uses  such  as found  in taxi, police  or delivery service. 
regularly  reaches 
90°F (32°C) 
or higher. 
If  you  do  not  use  your  vehicle under  any  of these 
conditions,  change  the  fluid and filter at 
100,000 miles (166 000 km). 
See  Part 
A: Scheduled  Maintenance  Services on 
page 
6-4. 
How to Cheek 
Because  this operation  can be  a  little difficult,  you may 
choose  to have  this done  at the  dealership service 
department. 
If  you  do  it yourself,  be sure  to follow  all  the  instructions 
here,  or  you  could get a false  reading  on the  dipstick. 
Nofice: Too much  or too  little  fluid  can damage 
your  transaxle. 
Too much  can  mean  that  some of the 
fluid  could  come  out and  fall on  hot  engine  or 
exhaust system parts,  starting  a  fire. 
Too little fluid 
could  cause  the transaxle  to  overheat. Be  sure 
to  get  an accurate  reading 
if you  check  your 
transaxle  fluid. 
Wait  at  least 30 minutes before checking  the transaxle 
fluid  level 
if you  have  been  driving: 
When  outside temperatures are  above 
90°F (32°C). 
At  high  speed  for  quite a  while. 
In  heavy  traffic 
- especially  in hot  weather. 
While pulling  a trailer. 
5-27