2003 Peugeot 307 CC boot

22-09-2003
PRACTICAL INFORMATION
136
Direction indicator side
repeaters (WY 5 W amber). 
Push the repeater forwards and
release the assembly.
 Hold the connector and turn thelens a quarter turn.
 Change the bulb. Rear lights
1 - Brake lights (diodes).
2 - Side lights (diodes).
3 - Direction indicators (P 21 W).
4 - Reversing light (P 21 W),
left side.
Fog lamp (P 21 W), right side. Direction indicators 
Remove the 3 bolts of the corre- sponding boot side trim to access
the light (use the 20 Torx TM
adaptor
of tool Clocated in the handbook
pocket),
 Remove the light fixing nut insidethe boot,
 Remove the light,
 Unscrew the bulb holder 5a
quarter of a turn,
 Remove the bulb holder,
 Change the faulty bulb.
Note: When refitting, take care to
position the bulb holder and the light
correctly.
Amber coloured bulbs
(direction indicators andside repeaters), must bereplaced with bulbs ofidentical specification
and colour.
All work on the diode lights must be carried out
by a PEUGEOT dealer.

22-09-2003
PRACTICAL INFORMATION
136
Direction indicator side
repeaters (WY 5 W amber). 
Push the repeater forwards and
release the assembly.
 Hold the connector and turn thelens a quarter turn.
 Change the bulb. Rear lights
1 - Brake lights (diodes).
2 - Side lights (diodes).
3 - Direction indicators (P 21 W).
4 - Reversing light (P 21 W),
left side.
Fog lamp (P 21 W), right side. Direction indicators 
Remove the 3 bolts of the corre- sponding boot side trim to access
the light (use the 20 Torx TM
adaptor
of tool Clocated in the handbook
pocket),
 Remove the light fixing nut insidethe boot,
 Remove the light,
 Unscrew the bulb holder 5a
quarter of a turn,
 Remove the bulb holder,
 Change the faulty bulb.
Note: When refitting, take care to
position the bulb holder and the light
correctly.
Amber coloured bulbs
(direction indicators andside repeaters), must bereplaced with bulbs ofidentical specification
and colour.
All work on the diode lights must be carried out
by a PEUGEOT dealer.

22-09-2003
PRACTICAL INFORMATION137
Number plate lights (W 5 W) 
Insert a thin screwdriver into one of the external holes of the lens.
 Push it outwards to unclip it.
 Remove the lens.
 Change the faulty bulb.
Third brake light (diodes)
Reversing light/fog lamp  unclip the corresponding boot lid trim at two points,
 move the trim aside gently toaccess the bulb holder 6,
 unscrew the bulb holder a quar-ter of a turn,
 remove the bulb holder,
 change the faulty bulb.
Note: When refitting, take care to
position the bulb holder correctly.
All work on the diode lights must be carried out
by a PEUGEOT dealer.

PRACTICAL INFORMATION
148
Moving shelf
Boot lid
Hinged covers Screen
Roof locking bolt
Bleed screw
Boot sill Plastic covers
22-09-2003

PRACTICAL INFORMATION149
Manual closing of the roof (emergency mode) If the roof opening or closing cycle does not begin or does not function
correctly, check the following points: 
ignition key in position acces- sories or running position (1st or2nd notch),
 the screen must be pulled out,
 the boot must be closed,
 the vehicle speed must be below
6 mph (10 km/h),
 the roof fuse must be in good con-dition (see corresponding section),
 the windows must be initialised(see corresponding section),
 the battery voltage must be suffi-cient (the roof control button indi-cator light must be lit),
 the vehicle must not be subject to"Economy mode active" restric-
tions (see corresponding section),
 the exterior temperature must not
be below Ð20 ¡C.
When carrying out the roof closing operation, take carenot to catch your hands inthe mechanisms.
In the event of an electrical or hydraulic roof malfunction, it is
possible to close the roof manually.
Contact a PEUGEOT dealer to have the system checked. This possibility is a breakdown
solution.Following manual closing of the roof, the boot lid hinges will no longer belocked and the boot will no longer besealed.
Two people are required to carry out this operation. Considerable
force is necessary.  Park the vehicle, if possible on level ground.
 Lower the windows.
 Switch off the ignition.
 Apply the handbrake.
The following two tools are provided in the handbook pocket: Allen TM
key with 5 adaptor Aand
6 adaptor B,
 Torx TM
key with 20 adaptor Cand
30 adaptor D.
22-09-2003

22-09-2003
PRACTICAL INFORMATION
150

Open the boot lid.
 Using the hook 1, secure the boot mat on the screen
bar 2.
This allows access to the hydraulic pump screw.
 Press the Allen TM
key adaptor Bfirmly into the bleed
screw 3, then unscrew half a turn. Using the Torx TM
key adaptor C, remove the six plastic
cover bolts 4, located on either side of the boot.
 Remove the two plastic covers 5.
 Extract the cable buckles 6from the trims.
Note: if a cable buckle is not visible, carefully insert your
hand behind the trim to extract it.

22-09-2003
PRACTICAL INFORMATION151

Pull the two control cables 7at the same time to unlock
the boot lid locks.
 While continuing to pull the cables, lift the boot lid hinges 8carefully.
Considerable force is required. Release the cables. Then, lift the assembly rearwards.
Note: the unfolding of the hinges locks the lid in the upper
position. Raise the moving shelf 9lifting it on either side.
Considerable force is required.
 Guide the movement of the shelf until it is in a vertical position.
 Take hold of the roof 10, unfold it (considerable force is
required) and move it as close as possible to the wind-screen.
 Reposition the boot mat and roll up the screen.

22-09-2003
PRACTICAL INFORMATION
152
To remove the boot sill trim: 
remove the three bolts 11, located inside the boot,
using the Torx TM
key adaptor C,
 remove the two bolts 12, located on the boot sill, using
the Torx TM
key adaptor D.
 Unclip the boot sill trim 13to access the hinged covers
motor. Using the Allen TM
key adaptor A, unscrew the central
bolt 14to fold the hinged covers 15to the end of their
travel.