
Remote  Alarm 
When  you  press the button with the  horn symbol  on the 
remote  keyless  entry  transmitter,  the parking lamps 
will  flash  and  the  horn 
will sound. This  will allow you  to 
attract  attention, 
if needed. 
Press  the panic  button  again to stop  the alarm from 
sounding. 
Remote  Power  Sliding  Door  Operation 
If your  vehicle  has the power  sliding  door, your remote 
keyless  entry  transmitter  will have a button that has a van 
symbol  on it.  Press  it  to  open or close the sliding  door. 
See 
Power  Sliding  Door (PSD)  on page 2- 16. 
If your  vehicle  has  the  dual  power sliding doors,  your 
remote  keyless  entry  transmitter  will  have two buttons 
that  have  a van  symbol  on them. The van symbol  on the 
left  is for  the  driver’s  side  sliding door and the van 
symbol  on  the  right  is for  the  passenger’s  side sliding 
door.  See 
Power  Sliding  Door (PSD) on page 2-16. 
If the  power  sliding  door(s)  is locked, first  unlock all 
doors,  then  press  the van  symbol  to open the power 
sliding  door(s). The parking lamps  will flash  when 
the  right  button  with  the  van  symbol is pressed and they 
will  not  flash  when  the  left  button with the van symbol 
is  pressed.  Press  the  van  symbol again to close the 
sliding  door(s).  See 
Power  Sliding  Door (PSD) on 
page 2- 16 for  more  information.  You 
can operate the power sliding door(s) with the 
remote keyless entry transmitter  only when the  power 
sliding door override  switch(es) on the overhead 
console  is turned 
off. See Power  Sliding  Door  (PSD) 
on  page 
2- 16. 
If your vehicle’s fuel filler  door is opened,  the driver’s  side 
power sliding door  will  not open completely. 
Do not try to 
force the  door. Once the fuel filler  door is closed, the 
driver’s side sliding  door can be opened normally. 
Matching Transmitter(s)  to  Your Vehicle 
Each remote keyless  entry transmitter  is coded to 
prevent another transmitter from  unlocking your vehicle. 
If a transmitter  is lost  or stolen, a  replacement can 
be purchased through  your  dealer. Remember to bring 
any  remaining transmitters  with  you when you  go to 
your dealer.  When the dealer matches the  replacement 
transmitter  to  your vehicle,  any remaining transmitters 
must also  be matched. Once your dealer  has  coded the 
new transmitter, the  lost transmitter will  not unlock 
your vehicle.  Each vehicle can  have a  maximum  of 
+^..I .L .----- :.LL--- --L-L^--I I- :A IUUI LI a1 131 I IILLGI 3 I I I~LCII IGU LV 11. 
See  your dealer to match transmitters  to another vehicle. 
2-7  

Battery Replacement 
Under normal use, the  battery  in your  remote  keyless 
entry transmitter should  last about three  years. 
You  can tell  the  battery  is weak  if  the transmitter  won’t 
work  at the  normal  range  in  any  location. 
If you have 
to  get  close  to your vehicle before the transmitter  works, 
it’s  probably time  to change  the battery. 
Notice: When  replacing the  battery,  use care not to 
touch any  of the circuitry. Static  from your body 
transferred  to these surfaces  may damage the 
transmitter. 
1. Insert a flat  object  like a coin into  the  slot  on  the 
side  of the  transmitter  and twist 
it to  separate  the 
halves. 
2. Gently pry the  battery  out of the  transmitter. Do not 
3. Replace the  battery. 
4. Reassemble  the transmitter.  Make  sure  the  halves 
use the 
metal flanges  to  pop  out  the  battery. 
are snapped  together  tightly 
so water  will  not  get  in. 
5. Press and hold  the  LOCK  and  UNLOCK  buttons  for 
6. Check  the transmitter  operation. 
seven seconds 
to  synchronize  the  transmitter. 
2-8  

Doors and Locks 
pAAu Locks 
I 
U xked doors  can be angerous. 
Passengers - especially  children - can 
easily  open  the  doors  and  fall  out  of  a  moving  vehicle.  When  a  door 
is locked, 
the  handle  won't  open 
it. You  increase  the 
chance 
of being  thrown  out  of  the  vehicle 
in  a  crash  if  the  doors  aren't  locked. 
So, 
wear  safety  belts  properly  and  lock  the 
doors  whenever  you drive. 
vehicles  may  be unable  to  get  out. A  child 
can  be  overcome  by  extreme  heat  and  can 
from  heat  stroke.  Always  lock  your  vehicle 
whenever  you  leave 
it. 
CAUTION:  (Continued) 
Young  children  who  get  into  unlocked 
s~ffer nnrmannnt inilwinc ~r pgn +~fh P" *."-s---.- "-'1-' --- 
Outsiders  can  easily  enter  through  an 
unlocked  door  when  you  slow  down  or 
stop your  vehicle.  Locking  your  doors  can 
help  prevent  this  from  happening. 
There  are several  ways to lock  and unlock your vehicle. 
From the outside,  use your  key  or  the remote keyless 
entry transmitter. 
To unlock either front  door from  the outside  .with the 
key,  insert  the  key  and turn  it toward the  front  of 
the vehicle.  If your  vehicle  has  power  door locks, 
you  can  unlock all  of the  doors  and  the  liftgate  by 
inserting the  key, turning  it toward  the front  of the 
vehicle and  holding it there for  one  second. 
To lock 
either front door  from  the outside with  your  key insert  the 
vehicle has  power  door  locks,  all of the  doors  will unlock 
when  you  insert  the  key and turn  it toward the  rear  of 
the  vehicle. 
key 2nd turn it tn?ncxc! the re2r e! the ?/ehIc!e. !f yxrr 
2-9  

You  can  lock all doors  and  the  liftgate  from the  inside 
by  pressing  the rear  of the  power  lock switch on 
either  front  door.  With  the  content theft-deterrent system, 
the  power  door  lock  switch  may cause the system to 
arm.  See 
Content Theft-Deterrent  on  page 2-27 for 
more  details. 
Also, when  the  doors  are  locked with the power door 
locks,  the  inside as  well  as the outside  door handle 
cannot  open  the  doors.  This safety feature prevents  a 
door  from  being accidentally  opened from the inside 
by  moving  the handle. 
To override  this safety  feature,  unlock the door you 
want  to  open. 
When  the liftgate  has  been  unlocked with the  power 
door  locks,  you won’t  need  the  key to open  it. Simply 
squeeze  the handle  located  above the  license plate. 
This  is also  true 
if you  use  the  remote keyless entry 
transmitter.  See 
Remote  Keyless  Entry  System  on 
page 
2-5. 
Last Door Closed Locking 
The last door closed locking  feature will delay the  power 
locking  of the doors and liftgate for  up to five  seconds 
after exiting  the vehicle,  when the  power  door  lock 
switch or the  lock button  on the  remote  keyless entry 
transmitter  is used  to lock  your  vehicle. 
To cancel this  delay, press the  power door  lock 
switch or  the lock button  on the  remote  keyless entry 
transmitter  a second time  immediately. 
If any door OF the  liftgate is  open  when locking the 
vehicle,  three chimes will  be heard signaling that  last 
door closed locking  is being  used.  Five  seconds after the 
last  door  is closed, all  of the  doors  will lock. 
If the  ignition is in RUN or ACCESSORY, this feature 
will  not lock the  doors. 
To  turn  the last  door  closed locking feature 
off or on, 
see 
Vehicle Personalization  on  page 2-62. 
2-1 1  

Lockout  Protection 
The  lockout protection feature  makes it difficult for  you 
to  lock  your  keys in your  vehicle. 
If the driver’s  door 
is  open  while  the  keys are in the  ignition,  a  chime will 
sound  and  you  will  not be able to  use  your  power 
door  lock  switch  to lock the vehicle. 
If you  don’t  leave  the  keys in the ignition or if you  use  the 
manual  door  lock,  you  could still lock your  keys in your 
vehicle.  Always  remember  to take  your  keys with you. 
To  turn this  feature  off  or  on, see 
Vehicle 
Personalization 
on page 2-62. 
Leaving  Your  Vehicle 
If  you  are  leaving the vehicle, take  your keys,  open your 
door  and  set  the  locks from the inside.  Then  get  out 
and  close  the door. 
Dual Sliding Doors 
To open  either sliding  door from outside  the vehicle,  pull 
the  handle  out and then  pull  the door toward  the  rear. 
If you slide  the door  all the  way  back,  the door  will rest  in 
a  detent position. 
To  move  the door  forward,  you  must  first pull the door 
past  the open  detent position. 
The  driver’s side sliding  door 
is designed to open  only a 
little 
if the  fuel  door  is open.  If  this ever  happens,  don’t  try 
to force the sliding door. Just close the driver’s side  sliding door.  Then  when the fuel  filler  door  is closed, 
the driver’s side sliding  door  can  be opened normally. 
2-1 3  

If your vehicle has the  power sliding door(s), you can 
override  the security lock by  pressing either power  door 
lock switch when the  power sliding door override 
switch(es)  is turned 
off. When  the  power sliding door 
override switch(es)  is turned  on, the power sliding 
door(s)  cannot be opened from  the  inside  when the 
sliding  door security lock  is in  use. 
If  you  want  to  open  the  sliding door when the  security 
lock  is on,  unlock  and open the door from the  outside. 
You  should  let  adults and older children know  how 
the  security lock  works, and how  to cancel the lock. 
If you don’t,  adults  or older children  who ride in  the rear 
won’t  be able  to  open the  sliding  door from the  inside 
when the  security lock feature  is in  use. 
Canceling the  Sliding Door 
Security Lock 
1. Unlock  the sliding door and  open the door  from 
2. Push  the  security lock lever all the  way  down. 
the 
outside. 
3. Close  the door. 
4. Repeat  Steps 1 through 3 for the  other  door. 
The sliding  door lock will  now  work normally. 
Power Sliding Door (PSD) 
If your vehicle has  this  feature,  you can open  and  close 
the sliding  door(s)  using  the  switches  inside  of your 
vehicle. You can  also  operate  the  power  sliding  door(s) 
with  your  remote  keyless  entry  transmitter.  See 
Remote 
Keyless  Entry  System  on  page 
2-5. 
Leaving your  children  or  pets unattended  in 
your  vehicle can  be  dangerous.  They  could 
operate  the  power  sliding  door. 
A child or 
others  could be injured.  Do  not leave  children 
or  pets  unattended  in your  vehicle. 
To help  avoid  accidental  operation  of the  sliding  door(s), 
press the  part of the  power  sliding  door  override 
switch(es)  with the don’t  symbol. 
2-1 6  

To open  or  close  the  sliding door(s), press and release 
one  of  the  following  power  door switches. 
.3 
Power  Sliding  Door 
~~~ 
Power Sliding  Door 
Override 
If you  have  the  one  power  sliding door, these switches 
are  located  in  the  overhead  console switchbank. 
If you have  the dual sliding 
doors,  your vehicle has 
these  switches. The left 
switch  is for  the  driver’s 
side  power sliding door and 
the  right  switch  is for the 
passenger’s side sliding 
door.  The power sliding 
door  and the power sliding 
door  override  is one  switch. 
Pressing the part  of the  switch(es)  with  the don’t symbol 
turns  the power to the sliding door(s) 
off. When  the power 
sliding door(s)  is 
off, you will not  be able to open  the 
door(s)  by using the power sliding  door switch(es) located 
on the overhead console  switchbank, using the switch in 
front  of the driver’s  or the  passenger’s  side sliding door, 
or using the remote keyless entry transmitter. 
Nofice: When  your  vehicle  goes  through an 
automatic  car wash, be  sure  the power sliding 
door  is  turned 
off. If it isn’t, the power sliding door 
may  open  accidentally. 
2-1 7  

Resetting the Power Sliding Door 
The  power  sliding  door  may  operate incorrectly or  not 
at  all  because  of the  following  conditions: 
e A low  voltage  or  dead  battery, 
disconnecting  the  battery,  or 
if the instrument  panel  PWR/HEATED  SEAT PSD 
fuse  or  the  underhood  fuse  8, 
27 or  29  are 
removed  or blown. 
See 
Fuses and Circuit  Breakers on page 5-96 for  more 
information  about  your  fuse  panel. 
If  any  of  these  conditions  occur,  the  power sliding door 
will  need  to  be reset. 
If your  vehicle has the dual 
power  sliding  doors,  both  doors will  have to  be reset. 
To do  this: 
1. Check  to  be  sure  the  power sliding door is unlocked 
2. Turn  the ignition  key  to OFF. 
3. !f en, t~rrn the pnwer slidin? door override switch off. 
and  securely  closed. 
4. Remove  fuse 29 from the  underhood fuse  block. 
Leave 
it out for 30 seconds. 
5. Reinstall the fuse and  wait 10 seconds. 
6.  Turn the  power sliding  door override switch  on. 
7. Press either of the  power  door lock switches to open 
the power sliding  door. 
8. Open the door all  of the  way. 
9. Wait  five  seconds  and close  the  door  by pressing 
either power door lock switch. 
IO. Wait  five  seconds and  repeat Steps 7 through  9. 
If the door  does  not rest in the  fully open position 
after  repeating Step 
7, repeat  Steps 7 through 9 again. 
If the  door  still does not operate correctly, see your 
dealer  for service. 
2-2 1