2003 OLDSMOBILE SILHOUETTE lock

How to Add Coolant to the Radiator
Notice: Your engine has a specific radiator fill
procedure. Failure to follow this procedure could
cause your engine to overheat and be severely
damaged.
If you hear a hiss, wait for that to stop. A hiss
means there is still some pressure left.
1. You can remove the radiator pressure cap when
the cooling system, including the radiator pressure
cap and upper radiator hose, is no longer hot.
Turn the pressure cap
slowly counterclockwise until
it first stops. (Don’t press down while turning the
pressure cap.)
2. Then keep turning the pressure cap, but now push
down as you turn it. Remove the pressure cap.
5-34

Notice: If you leave your radio on, it could be badly
damaged. The repairs wouldn’t be covered by
your warranty.
3.
4.
Turn off the ignition on both vehicles. Unplug
unnecessary accessories plugged into the cigarette
lighter or in the accessory power outlet. Turn
off
the radio and all lamps that aren’t needed. This will
avoid sparks and help save both batteries. And it
could save your radio!
Open the hoods and locate the batteries. Find the
positive
(+) and negative (-) terminal locations on
each vehicle.
You will not need to access your battery for jump
starting. Your vehicle has a remote positive
(+)
jump starting terminal for that purpose. The terminal is located
under a tethered cap at
the front of the underhood
fuse block. See
Engine
Compartment Overview
on page
5- 12 for more
information on location.
Squeeze the tabs and pull up
on the cap to access
the remote positive
(+) terminal. You should always
use the remote positive
(+) terminal instead of the
positive (+) terminal on your battery.
An electric fan can start up ever !hen the
engine is not running and can injure you.
Keep hands, clothing and tools away from any
underhood electric fan.
5-45

3. Pull the front turn signaVparking lamp assembly
away from the vehicle.
Front Turn SignaVParking Lamp
4.
5.
6.
Front Sidemarker Lamp
Unscrew the bulb socket from the lamp assembly
by pressing the tab while turning it
counterclockwise.
Replace the bulb by pulling the old one out and
gently pushing the new one into the lamp socket.
Line up the tabs on the socket with the gaps in the
socket holes and screw the bulb socket back into
the lamp housing until a click is heard (the tab
popping back out).
5-55

Changing a Flat Tire
If a tire goes flat, avoid further tire and wheel damage
by driving
slowly to a level place. Turn on your
hazard v.--nin- 'lashers.
Chan,,,lg a tire can cause an injury. The
vehicle can
slip off the jack and roll over you
or other people.
You and they could be badly
injured. Find a level place to change your tire.
To help prevent the vehicle from moving:
1. Set the parking brake firmly.
2. Put the shift lever in PARK (P).
3. Turn off the engine.
To be even more certain the vehicle won't
move, you can put blocks at the front and
rear of the tire farthest away from the one
being changed. That would be the tire on
the other side
of the vehicle, at the
opposite end. The following
steps will tell you how to use the jack and
change a tire.
5-70

C
The tools you’ll be using include the jack (A),
extension
(B) and folding wrench (C).
The compact spare tire is located under the rear of
the vehicle. See “Compact Spare Tire” later in this
section for more information about the compact spare. To
remove the compact spare tire, do the following:
B
-C
A. Hoist Shaft
B. Hoist Assembly
C. Retainer
D. Compact Spare Tire E. Extension
(Chisel End)
F. Folding Wrench
I. Attach the folding wrench to the extension and
insert the chisel end on an angle through the
hole in the rear bumper and into the hoist shaft.
2. Turn the folding wrench counterclockwise to lower
the compact spare tire to the ground. Continue to
turn the wrench
so the compact spare tire can
be pulled out from under the vehicle.
5-72

3. To remove the compact spare tire from the cable,
tilt the retainer at the end
of the cable so it can be
pulled up through the wheel opening.
-. If your vehicle is an all-wheel-drive vehicle, after
removing the compact spare tire turn the wrench
clockwise to raise the cable back up.
On an AWD vehicle, you can not store
a full-size
tire under the vehicle. It should be stowed inside the
vehicle by the cable provided. See “Storing the
Flat Tire on an All-Wheel-Drive Vehicle” later
in
this section.
If you have a front-wheel-drive vehicle, the hoist is
used to store a full-size or a flat road tire under
the vehicle. See “Storing the Spare Tire and
Tools”
and “Storing the Flat Tire on a Front-Wheel-Drive
Vehicle” later
in this section.
If the compact spare tire will not lower, check under the
vehicle to see
if the tire is hanging loose and the cable
end and spring under the wheel plate are missing. If
so,
the secondary latch system is engaged. See “Secondary
Latch System” later
in this section.
To continue changing the flat tire see “Removing the
Flat Tire and Installing the Spare Tire” later in this
section.
5-73

1. Place the jack under the vehicle, ahead of the rear
bumper. Position the center
lift point of the jack
under the center of the compact spare tire.
2. Turn the folding wrench clockwise to raise the jack
until it lifts the secondary latch device under the
wheel plate.
5. Grasp the compact spare tire with both hands and
6. Reach under the vehicle and remove the folding
pull
it out
from under the vehicle.
wrench and jack.
Have the hoist assembly inspected as soon as you can.
You will not be able to store a spare or flat tire usinG
the hoist assembly until it has been repaired or replaced. 3. Keep raising tne jack untii rne compact spare tire
stops moving upward and is held firmly in place,
this lets you know that the secondary latch
has released.
4. Lower the jack by turning the folding wrench
counterclockwise. Keep lowering the jack until
the compact spare tire is resting on the folding
wrench. ~- -~
5-75

Removing the Wheel Covers
If the wheel has a center cap, use the handle of the
folding wrench to pry
it off. Then, with the other end of
the folding wrench, loosen the nuts.
If your vehicle has the plastic “bolt-on” wheel covers,
loosen the bolts completely using the folding wrench,
and remove the wheel cover.
Removing the Flat Tire and Installing
the Spare Tire
1. Loosen the wheel
nuts
- but do not
remove them
- using
the folding wrench.
(Turn the handle about
180 degrees, then flip
the handle back to
the starting position.
This avoids taking the
wrench
off the lug nut
for each turn.)
For wheels with
a wheel lock key, use the wheel
lock key between the lock nut and folding wrench.
The key is supplied
in the front passenger door
pocket.
Notice: To help avoid damage to lock nut or wheel
lock key, do not
use an impact wrench with this key.
5-76