As you signal a turn or a lane change, if the arrows
flash very fast, a bulb may be burned out and
other drivers won’t see your turn signal.
If a bulb is burned out, replace
it to help avoid an
accident.
If the arrows don’t go on at all when you signal a turn,
check the fuse (see
Fuses and Circuit Breakers on
page
5-92 ) and check for burned-out bulbs.
Turn Signal On Chime
If your turn signal is left on for more than 0.8 miles
(1.3 km), a chime will sound at each flash of the turn
signal and the DIC will display the TURN SIGNAL
ON?
reminder message. To turn off the chime and
message, move the turn signal lever to the
off position.
To turn off the DIC message while the turn signal is
still active, press any button on the DIC. See
Driver
information Center (DE) on page 3-45 for more
information.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high, push
the lever away from you until you hear a click. Then
release it.
When the high beams are
on, this light on the
instrument panel cluster
will also be on.
If the fog lamps are on when you turn on the high-beam
headlamps, the fog lamps will turn
off. The fog lamps
will turn back on when you turn
off the high-beam
headlamps.
3-7
ProCarManuals.com
Flash-to-Pass
This feature lets you use your high-beam headlamps to
signal a driver in front
of you that you want to pass.
It works even
if your headlamps are off.
To use it, pull the turn signal lever toward you.
Your high-beam headlamps will turn on. They’ll stay on
as long as you hold the lever there. Release the
lever
to turn them off.
If your headlamps are on, and on high beam, your
headlamps will switch to low beam when the lever is
released.
To get back to high beam, push the lever away
from you.
Windshield Wipers
The lever on the right side of your steering column
operates your windshield wipers.
If your windshield wipers are on for more than
six
seconds while you are driving, the low-beam headlamps,
instrument panel cluster backlighting and the taillamps
will turn on. For more information see “Wiper-Activated
Headlamps” under
Exterior Lamps on page 3-14.
3-8
ProCarManuals.com
For a single wiping cycle, move the lever down to MIST.
Hold it there until the wipers start, then release it. The
wipers will stop after one cycle.
If you want more cycles,
hold the lever on MIST longer.
For steady wiping at low speed, move the lever up to
the
LO position. For high-speed wiping, move the lever
up further, to HI.
To stop the wipers, move the lever
to OFF.
You can set the wiper speed for a long or short delay
between wiper cycles. Move the lever up to the first
detent, INT (Intermittent). Turn the band labeled
INT ADJ (Intermittent Adjustment) down toward the
shorter lines for fewer wiper passes per minute. As you
turn the band toward the longer lines, the wiper
cycles per minute will increase.
Remember that damaged wiper blades may prevent you
from seeing well enough to drive safely. To avoid
damage, be sure to clear ice and snow from the wiper
blades before using them. If they’re frozen to the
do become damaged, get new blades or blade inserts.
See
Windshield Wiper Blade Replacement on
page
5-59.
Heavy snow or ice can overload your wipers. A circuit
snow or ice to prevent an overload.
\yindrihield, ~~r~f~!Il;/ lcgspn 9~ thl~~! them. !f \/nllr hl=dnc J --’
breaker wi!! stop them unti! the mntnr con!s. C!ear away
RainsenseTM II Wipers
The moisture sensor is mounted on the interior side of
the windshield below the rearview mirror and is used
to automatically operate the windshield wipers.
This system operates by monitoring the amount of
moisture build-up on the windshield. Wipes occur as
needed to clear the windshield depending on the driving
conditions and sensitivity setting. In light rain or snow,
fewer wipes will occur. In heavy rain or snow, wipes will
occur more frequently. The system will operate in the
delay, low speed and high speed modes. If the system is
left on for long periods of time, occasional wipes may
occur without any moisture
on the windshield. This
is normal and indicates that the RainsenseTM system is
activated.
3-9
ProCarManuals.com
Resuming a Set Speed
Setting the cruise control at a desired speed and then
applying the brake will end the cruise control function.
Once you’re going about
25 mph (40 km/h) or more, you
can briefly push the cruise control lever up to RES-ACC
(Resume-Accelerate) to reset. This returns you to
the desired preset speed.
Remember,
if you hold the lever up at RES-ACC, the
vehicle will accelerate until you release the lever
or apply the brake.
So unless you want to go faster,
don’t hold the lever at RES-ACC.
Increasing Speed While Using Cruise
Control
1.
2.
3.
4.
Push the cruise control switch, located on the right
side of the steering column at the end of the lever,
in to
ON.
Get up to the speed you want.
Push the lever down to SET-CST (Coast) and
release it. The CRUISE light on the instrument
panel cluster will come on.
Take your foot
off the accelerator pedal. There are
three ways to go to a higher speed:
Use the accelerator pedal to go to a higher speed.
Push the lever down, then release the lever and
the accelerator pedal. You’ll now cruise at the higher
speed.
Move the cruise lever up to RES-ACC. Hold it there
until you reach a desired speed and then release
the lever.
3-1 2
ProCarManuals.com
To increase your speed in very small amounts,
move the lever up to RES-ACC briefly and then
release it. Each time you do this, your vehicle will go
about
1 mph (1 -6 km/h) faster.
The accelerate feature will only work after you have set
the cruise control speed by pushing the lever down
to SET-CST.
Reducing Speed While Using Cruise
Control
There are two ways to reduce your speed while using
cruise control:
@ Push the lever down until you reach a desired lower
speed then release it.
To slow down in very small amounts, push the lever
down briefly. Each time you do this, you’ll go about
1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your speed.
When you take your foot
off the pedal, your vehicle will
slow down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load, and the steepness of the
hills. When going up steep hills, you may have to step
on the accelerator pedal to maintain your speed.
When going downhill, you may have to brake or shift to
a lower gear to keep your speed down. Of course,
applying the brake takes you out of cruise control. Many
drivers find this to be too much trouble and don’t use
cruise control on steep hills.
Ending Cruise Control Without Erasing the
Set Speed
There are two ways to turn off the cruise control:
* Step lightly on the brake pedal, or
@ pull the cruise lever towards you to cancel cruise.
To resume the set speed see “Resuming a Set Speed”
earlier in this section.
Erasing Speed Memory
When you turn off the cruise control or the ignition, your
cruise control set speed memory is erased.
3-1 3
ProCarManuals.com
Exterior Lamps
The lever on the left side
of the steering column
operates the exterior
lamps.
{OO: (Parking Lamps): Turning the switch to this
position turns on the parking lamps, together with the
following:
Sidemarker Lamps
Taillamps
-:g- : Turn the outside part of the lever with this symbol
on
it, to operate the lamps. The exterior lamp switch
has three positions.
OFF: Turning the switch to this position turns off all
lamps and lights, except the Daytime Running
Lamps
(DRL).
License Plate Lamps
Instrument Panel Lights
- - zo (Headlamps): Turning the switch to this position
turns on the headlamps, together with the previously
listed lamps and lights.
AUTO (Automatic Headlamps): Turning the exterior
lamps control to AUTO will turn the headlamps, taillamps
and parking lamps on and
off, while the ignition is on,
by sensing how dark it is outside. See “Automatic
Headlamp System” later in this section for more
information.
3-1 4
ProCarManuals.com
Wiper-Activated Headlamps
This feature turns on the low-beam headl,amps,
instrument panel cluster backlighting and taillamps after
the windshield wipers have been in use for
approximately six seconds. To operate, the exterior
lamps control must be in AUTO and it must be
dark enough outside.
When the exterior lamps control is in OFF or the
parking lamp position and the windshield wiper control
is on (LO, HI or INT), the HEADLAMPS SUGGESTED
message
will appear on the DIC.
When you turn the key to OFF, the wiper-activated
headlamps will immediately turn off. The wiper-activated
headlamps will also turn off
if you turn the exterior
lamps control to OFF or turn off the windshield wipers.
Headlamps on Reminder
If the exterior lamps control is left on, you’ll hear a
warning chime when you turn the ignition off, remove
the key from the ignition and open the driver’s door.
nrr..+;mrr bllmm:mre* I n--IcI uayrllIIG IIUIIIIIII~ Lalllpa
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the
day. DRL can be helpful
in many different driving
conditions, but they can be especially helpful in the short
periods after
dawn and before s~Jnset. FL!!!~ f~jnctiona!
daytime running lamps are required on all vehicles
first sold in Canada. A
light sensor on top of the instrument panel makes the
DRL work,
so be sure it isn’t covered.
The DRL system will make your high-beam headlamps
come on at reduced brightness in daylight when the
following conditions are met:
The ignition is on,
the exterior lamps control is off, and
e the transaxle is not in PARK (P).
When the DRL are on, only your high-beam headlamps
will be on. The parking lamps, taillamps, sidemarker
and other lamps won’t be on.
With your headlamp control in AUTO when it is dark
enough outside, your low-beam headlamps will
automatically come on. The other lamps that turn on
with your headlamps will also turn on. When it is bright
enough outside, the regular lamps will go
off, and
your high-beam headlamps change to the reduced
brightness of DRL.
To turn off all exterior lighting at night when you are
parked, turn the exterior lamps control all the way toward
OFF. The DRL will turn on automatically and the
HEADLAMPS SUGGESTED message will be displayed
on the DIC when you move the transaxle out of
PARK (P).
3-1 5
ProCarManuals.com
If the exterior lamps control is in the parking lamps
position at night, only the parking lamps will be on.
If the
transaxle is out of PARK
(P), only the parking lamps
will be active and the HEADLAMPS SUGGESTED
message will be displayed on the DIC.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Automatic Headlamp System
The automatic headlamp system will keep your
headlamps on when it is dark outside and the ignition
is
in ON.
It’s possible that your headlamps may go out if you
drive from a dark area into a bright area like a lighted
parking lot.
If this happens, turn on your headlamps with
the exterior lamps control.
Light Sensor
Your automatic headlamps and DRL work with the light
sensor on top of the instrument panel. Don’t cover it
up.
If you do it will read “dark” and the automatic
headlamp lighting will turn on.
Fog Lamps
To turn on only the front
fog lamps, turn the fog
lamp band to the single fog
lamp symbol. To turn on both the front and rear fog
lamps, turn the fog
lamp band to the double
fog lamp symbol.
Turning on the front fog lamps only will automatically
activate the parking lamps. Turning on the front and rear
fog lamps will automatically activate the parking lamps
and headlamps.
To turn
off the fog lamps, turn the band to OFF. The
front fog lamps will also turn
off when you turn on your
high-beam headlamps, but
will turn on again when
you switch to low beams.
Continuous use of the fog lamps will shorten bulb life
Limit use as necessary.
3-1 6
ProCarManuals.com