2003 OLDSMOBILE AURORA garage door opener

Programming the HomeLink@
Transmitter
Do not use the HomeLink@ Transmitter with any garage
door opener that does not have the “stop and reverse’’
feature. This includes any garage door opener model
manufactured before April
1, 1982.
Keep the original transmitter for use in other vehicles as
well as for future HomeLink@ programming. It is also
recommended that upon the sale
of the vehicle,
the programmed HomeLink@ buttons should be erased
for security purposes. Refer to “Erasing HomeLink@
Buttons” or, for assistance, contact HomeLink@ on the
internet at: www.homelink.com or by calling
1 -800-355-35 1 5.
Be sure that people and objects are clear of the garage
door or gate operator you are programming. When
programming a garage door, it is advised to park outside
of the garage.
It is recommended that a new battery be installed in
your hand-held transmitter for quicker and more
accurate transmission of the radio frequency.
Your vehicle’s engine should be turned
off while
programming the transmitter. Follow these steps to
program up to three channels:
1. Press and hold down the two outside buttons,
releasing only when the indicator light begins to
flash, after 20 seconds.
Do not hold down the buttons
for longer than
30 seconds and do not
repeat this step to program a second and/or third
transmitter to the remaining two HomeLink@ buttons.
2. Position the end
of your hand-held transmitter about
1 to 3 inches (3 to 8 cm) away from the HomeLink@
buttons while keeping the indicator light in view.
3. Simultaneously press and hold both the desired
button on HomeLink@ and the hand-held transmitter
button.
Do not release the buttons until Step 4
has been completed.
Some entry gates and garage door openers may
require you to substitute Step
3 with the procedure
noted in “Gate Operator and Canadian
Programming” later in this section.
4. The indicator light will flash slowly at first and then
rapidly after HomeLink@ successfully receives the
frequency signal from the hand-held transmitter.
Release both buttons.
5. Press and hold the newly-trained HomeLink@ button
and observe the indicator light.
If the indicator light stays on constantly,
programming is complete and your device should
activate when the HomeLink@ button is pressed and
released.
To program the remaining two HomeLink@ buttons,
begin with Step 2 under “Programming HomeLink@.”
Do not repeat Step 1 as this will erase all of the
programmed channels.
2-42
ProCarManuals.com

If the indicator light blinks rapidly for two seconds
and then turns to a constant light, continue with
Steps
6 through 8 following to complete the
programming of a rolling-code equipped device
(most commonly, a garage door opener).
6. At the garage door opener receiver (motor-head
unit) in the garage, locate the “Learn” or “Smart”
button. This can usually be found where the hanging
antenna wire is attached to the motor-head unit.
7. Firmly press and release the “Learn” or “Smart”
button. The name and color of the button may
vary by manufacturer.
You will have
30 seconds to start Step 8.
8. Return to the vehicle. Firmly press and hold the
programmed HomeLink@ button for two seconds,
then release. Repeat the press/hold/release
sequence a second time, and depending on the
brand of the garage door opener (or other rolling
code device), repeat this sequence a third time
io compieie ine proyrarrllllirly.
HomeLink@ should now activate your rolling code
equipped device.
To program the remaining two HomeLink@ buttons,
begin with Step
2 of “Programming HomeLink@.” Do not
repeat Step
1.
Gate Operator and Canadian
Programming
Canadian radio-frequency laws require transmitter
signals to “time out” or quit after several seconds of
transmission. This may not be long enough for
HomeLinkO to pick up the signal during programming.
Similarly, some
U.S. gate operators are manufactured to
“time out” in the same manner.
If you live in Canada, or you are having difficulty
programming a gate operator by using the
“Programming HomeLink@’ procedures (regardless of
where you live), replace Step
3 under “Programming
HomeLinkm’ with the following:
Continue to press and hold the HomeLink@ button while
you press and release every two seconds (cycle)
your hand-held transmitter until the frequency signal has
been successfully accepted by HomeLink@. The
indicator light will flash slowly at first and then rapidly.
Proceed with Step
4 under “Programming HomeLink@”
to complete.
2-43
ProCarManuals.com

F
FabricKarpet ................................................. 5-82
Filter Engine Air Cleaner
...................................... 5-21
Finding a PTY Station
..................................... 3-63
Finding a Station
............................................ 3-60
Finish Care
.................................................... 5-85
Finish Damage
............................................... 5-87
Flash-to-Pass
................................................... 3-8
Flat Tire
........................................................ 5-70
Flat Tire, Changing
......................................... 5-71
Floor Mats
..................................................... 2-46
Fluid Automatic Transaxle
..................................... 5-22
Power Steering
........................................... 5-37
Windshield Washer
...................................... 5-38
Fog Lamps
.................................................... 3-16
Following Distance
.......................................... 4-40
Footnotes
........................................................ 6-5
Front Reading Lamps
...................................... 3-20
Front Storage Area
......................................... 2-45
Fuel
....................................................... 3-46, 5-5
Additives
...................................................... 5-6
California Fuel
.............................................. 5-6
Filling a Portable Fuel Container
.................... 5-1 1
Filling Your Tank ........................................... 5-7
FM
............................................................... 3-74 Fuel
(cont.)
Fuels in Foreign Countries
.............................. 5-7
Gage
......................................................... 3-44
Gasoline Octane
........................................... 5-5
Gasoline Specifications .................................. 5-5
System Inspection
....................................... 6-13
Fuel Economy
................................................ 3-47
Fuses Fuses and Circuit Breakers
........................... 5-92
Windshield Wiper
......................................... 5-91
G
Gage ........................................................ 3-49
Engine Coolant Temperature
......................... 3-38
Fuel
.......................................................... 3-44
Speedometer
.............................................. 3-32
Tachometer
................................................. 3-33
Garage
Door Opener ....................................... 2-41
Gasoline Octane
........................................................ 5-5
Gate Operator and Canadian Programming ........ 2-43
Glass Surfaces
............................................... 5-84
Glove Box
..................................................... 2-45
GM Mobility Program for Persons with
Disabilities
.................................................... 7-5
Specifications
............................................... 5-5
6
ProCarManuals.com