2003 NISSAN ALMERA N16 clutch

AT-424
[ALL]
DISASSEMBLY
28. Remove brake band according to the following procedures.
a. Loosen lock nut, then back off anchor end pin.
●Do not reuse anchor end pin.
b. Remove brake band and strut from transmission case.
●To prevent brake linings from cracking or peeling, do not
stretch the flexible band unnecessarily. When removing
the brake band, always secure it with a clip as shown in
the figure at right.
Leave the clip in position after removing the brake band.
c. Check brake band facing for damage, cracks, wear or burns.
29. Remove input shaft assembly (high clutch) and reverse clutch
according to the following procedures.
a. Remove input shaft assembly (high clutch) with reverse clutch.
SAT037DA
SAT038D
SAT039D
SAT040D
SAT041D

DISASSEMBLY
AT-425
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
b. Remove input shaft assembly (high clutch) from reverse clutch.
c. Remove needle bearings from high clutch drum.
d. Check input shaft assembly and needle bearing for damage or
wear.
30. Remove high clutch hub and needle bearing from trans mission
case.
31. Check high clutch hub and needle bearing for damage or wear.
32. Remove high clutch hub and front sun gear from transmission
case.
33. Check front sun gear and needle bearings for damage or wear.
SAT042D
SAT043D
SAT044D
SAT579D

AT-426
[ALL]
DISASSEMBLY
34. Remove low one-way clutch and front planetary carrier assem-
bly according to the following procedures.
a. Remove snap ring with flat-bladed screwdriver.
b. Remove front planetary carrier with low one-way clutch.
c. Check that low one-way clutch rotates in the direction of the
arrow and lochs in the opposite direction.
d. Remove low one-way clutch front planetary carrier by rotating it
in the direction of arrow.
e. Remove needle bearing front planetary carrier.
f. Check front planetary carrier, low one-way clutch and needle
bearing for damage or wear.
g. Check clearance between pinion washer and planetary carrier
using feeler gauge.
Replace front planetary carrier if the clearance exceeds allow-
able limit.
SAT046D
SAT047D
SAT048D
SAT022F
Standard clearance: 0.15 - 0.70 mm (0.0059 - 0.0276 in)
Allowable limit: 0.80 mm (0.0315 in)
SAT050D

AT-428
[ALL]
DISASSEMBLY
37. Remove needle bearing from rear internal gear.
●Check needle bearing for damage or wear.
38. Remove forward clutch assembly from transmission case.
39. Remove thrust washer from transmission case.
40. Remove output shaft assembly according to the following proce-
dures.
a. Remove side cover bolts.
b. Remove side cover by lightly tapping it with a soft hammer.
●Be careful not to drop output shaft assembly. It might
come out when removing side cover.
SAT056D
SAT272E
AAT215A
SAT059D
SAT434D

REPAIR FOR COMPONENT PARTS
AT-443
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
●Check to see that retainer plates are properly positioned in
upper body.
●Be careful not to lose these parts.
Oil Strainer
●Check wire netting of oil strainer for damage.
Shift Solenoid Valves “A” and “B”, Line Pressure Solenoid Valve, Torque Converter Clutch
Solenoid Valve and Overrun Clutch Solenoid Valve
●Measure resistance.
●Except for EURO-OBD:
●For shift solenoid valve A, refer to AT- 3 5 7 , "SHIFT SOLENOID
VA LV E A" .
●For shift solenoid valve B, refer to AT- 3 6 2 , "SHIFT SOLENOID
VA LV E B" .
●For line pressure solenoid valve, refer to AT- 3 8 8 , "LINE PRES-
SURE SOLENOID VALVE" .
●For torque converter clutch solenoid valve, refer to AT- 3 7 2 ,
"TORQUE CONVERTER CLUTCH SOLENOID VALVE" .
●For overrun clutch solenoid valve, refer to AT- 3 6 7 , "OVERRUN
CLUTCH SOLENOID VALVE" .
●EURO-OBD:
●For shift solenoid valve A, refer to AT-171, "DTC P0750 SHIFT SOLENOID VALVE A" .
●For shift solenoid valve B, refer to AT-176, "DTC P0755 SHIFT SOLENOID VALVE B" .
●For line pressure solenoid valve, refer to AT-164, "DTC P0745 LINE PRESSURE SOLENOID VALVE" .
●For torque converter clutch solenoid valve, refer to AT-159, "DTC P0740 TORQUE CONVERTER
CLUTCH SOLENOID VALVE" .
●For overrun clutch solenoid valve, refer to AT- 1 8 7 , "DTC P1760 OVERRUN CLUTCH SOLENOID VALVE"
.
SAT321G
SAT115D
SAT283HB

REPAIR FOR COMPONENT PARTS
AT-449
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
Control Valve Upper BodyECS007TD
COMPONENTS
Numbers preceding valve springs correspond with those shown in AT- 5 1 5 , "SERVICE DATA AND SPECIFI-
CATIONS (SDS)" .
1. Control valve upper body 2. Return spring 3. Overrun clutch reducing valve
4. Plug 5. Retainer plate 6. Torque converter relief valve
7. Return spring 8. Retainer plate 9. Torque converter clutch control valve
10. Return spring 11. Plug 12. Sleeve
13. Retainer plate 14. 1-2 accumulator valve 15. Return spring
16. Plug 17. Retainer plate 18. Cooler check valve
19. Return spring 20. Plug 21. Retainer plate
22. Retainer plate 23. Return spring 24. Pilot valve
25. Retainer plate 26. Plug 27. 1-2 accumulator piston
28. Return spring 29. 1-2 accumulator retainer plate 30. Retainer plate
31. Plug 32. 1st reducing valve 33. Return spring
34. Retainer plate 35. Return spring 36. 3-2 timing valve
SAT863J

AT-452
[ALL]
REPAIR FOR COMPONENT PARTS
1-2 Accumulator Valve
●Install 1-2 accumulator valve. Align 1-2 accumulator retainer
plate from opposite side of control valve body.
●Install return spring, 1-2 accumulator piston and plug.
1. Install retainer plates.
●Install retainer plate while pushing plug or return spring.
Retainer Plate (Upper Body)
Unit: mm (in)
●Install proper retainer plates.
Refer to AT- 4 4 9 , "
Control Valve Upper Body" .
SAT142D
SAT143D
No. Name of control valve Width A Length B
22 Pilot valve
6.0 (0.236)21.5 (0.846) 30 1st reducing valve
34 3-2 timing valve
8 Torque converter relief valve
17 1-2 accumulator valve
38.5 (1.516)
25 1-2 accumulator piston
5 Overrun clutch reducing valve
24.0 (0.945)
21 Cooler check valve
13 Torque converter clutch control valve 28.0 (1.102)
SAT086F

REPAIR FOR COMPONENT PARTS
AT-453
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
Control Valve Lower BodyECS007TE
COMPONENTS
Numbers preceding valve springs correspond with those shown in AT- 5 1 5 , "SERVICE DATA AND SPECIFI-
CATIONS (SDS)" .
1. Control valve lower body 2. Return spring 3. Shift valve B
4. Plug 5. Retainer plate 6. Pressure modifier valve
7. Return spring 8. Parallel pin 9. Sleeve
10. Piston 11. Return spring 12. Retainer plate
13. Manual valve 14. Retainer plate 15. Sleeve
16. Plug 17. Spring seat 18. Return spring
19. Pressure regulator valve 20. Retainer plate 21. Plug
22. Overrun clutch control valve 23. Return spring 24. Retainer plate
25. Plug 26. Accumulator control valve 27. Return spring
28. Retainer plate 29. Return spring 30. Shift valve A
31. Retainer plate 32. Plug 33. Plug
34. Return spring 35. Shuttle control valve
SAT864J