15 Introduction
Symbols
Symbols
The following symbols are found in this
Operator’s Manual:
* Optional equipment is identified
with an asterisk. Since standard
equipment varies between models,
the descriptions and illustrations in
this manual may differ slightly from
the actual equipment of your vehi-
cle.
This symbol points to instructions for
you to follow.
A number of these symbols appearing
in succession indicates a multiple-step
procedure.
Page This symbol tells you where to
look for further information on a
topic.
This continuation symbol marks
an interrupted procedure which
will be continued on the next
page.
-> In the glossary of technical
terms, this symbol is used to
cross-reference term defini-
tions.
DISPLAY
Words appearing in the multi-
function display are printed in
the type shown here.
Warning!
G
Warning notices draw your attention to haz-
ards that may endanger your health or life,
or the health or life of others.!Highlights hazards that may result in
damage to your vehicle.iHelpful hints or further information you
may find useful.
33 Getting started
Unlocking
1KEYLESS-GO start/stop button
Before you press the KEYLESS-GO
start/stop button, the vehicle’s on-board
electronics have status 0 (as with
SmartKey removed).
Make sure the gear selector lever is set
toP.
Do not depress the brake pedal.Position 1
Press the KEYLESS-GO start/stop but-
ton once.
This supplies power to some electrical
consumers, such as seat adjustment.
Ignition (or position 2)
Press the KEYLESS-GO start/stop but-
ton twice in immediate succession.
This supplies power to all electrical
consumers. All the lights in the instru-
ment cluster light up.More information can be found in the
“Controls in detail” section (
page 85).
For information on starting the engine us-
ing the KEYLESS-GO start/stop button,
see “Starting with KEYLESS-GO*”
(
page 43).
iIf you now press the KEYLESS-GO
start/stop button twice, the power
supply is again switched off.iIf you now press the KEYLESS-GO
start/stop button once, the power sup-
ply is again switched off.
39 Getting started
Adjusting
Exterior rear view mirrorThe buttons are located on the driver’s
door.
1Driver’s side mirror
2Passenger side mirror
3Adjustment button
Make sure that the ignition is switched
on.
All the lights in the instrument cluster
light up.
Press button1 for the left mirror or
button2 for the right mirror.
Push adjustment button3 up, down,
left, or right according to the desired
setting.For information on the electrically folding
exterior rear view mirrors, see “Folding the
exterior mirrors in and out automatically”
(
page 170).
Warning!
G
Exercise care when using the passenger
side exterior rear view mirror. The mirror
surface is convex (outwardly curved surface
for a wider field of view). Objects in mirror
are closer than they appear. Check your in-
side rear view mirror or glance over your
shoulder before changing lanes.!Electrolyte drops coming into contact
with the vehicle paint finish can only be
completely removed while in their liq-
uid state and by applying plenty of wa-
ter.
!For information on how to reposition
the exterior mirror housing when it was
forcibly pushed forward (hit from the
rear) or forcibly pushed rearward (hit
from the front), see “Folding the exteri-
or mirrors in and out manually”
(page 170).
iAt low ambient temperatures, the mir-
rors will be heated automatically.
46 Getting startedDrivingSwitching on headlampsExterior lamp switch1Off
2Low beam headlamps on
Turn the switch to
B
.
For more information, see “Lighting”
(
page 120).
Turn signals and high beam
The combination switch is located on the
left of the steering column.Combination switch1Turn signals, right
2Turn signals, left
Press the combination switch up1 or
down2.High beam
Push the combination switch forward.
The high beam headlights are switched
on.
The high beam symbol
A
in the
tachometer lights up.
For more information, see “High beam
flasher” (
page 123).
iTo signal minor directional changes,
move combination switch to point of
resistance only and release. The turn
signal blinks three times.
53 Getting started
Parking and locking
Turning off engine with KEYLESS-GO*
Place the gear selector lever in P.
Press and hold the KEYLESS-GO
start/stop button until the engine
shuts off.
With the driver's door closed, the start-
er switch is now in position1. With the
driver’s door opened, the starter switch
is set to position0, same as SmartKey
removed from starter switch
(page 31).
Press the seat belt release button
(page 41).
1Lock button on the door handle
After exiting the vehicle, press lock
button1 on the door handle or on the
trunk lid.
The locking knobs on the doors move
down. The turn signal indicators light
up briefly.
For more information, see “Controls in de-
tail” (page 85).
!If you hear a warning signal you have ei-
ther:
forgotten to turn off the lights, or
not put the gear selector lever inP
before opening the driver’s door
Turn off the lights or place the gear se-
lector lever inP.
Warning!
G
To prevent possible personal injury, always
keep hands and fingers away from the door
openings when closing the doors. Be espe-
cially careful when small children are
around.
Before closing doors, make sure that there
is no possibility of someone getting caught
in a door during closing.
Warning!
G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take the
KEYLESS-GO* card (if so equipped) with
you, and lock your vehicle. Do not leave chil-
dren unattended in the vehicle, or with ac-
cess to an unlocked vehicle. Unsupervised
use of vehicle equipment may cause an ac-
cident and/or serious personal injury.
56 Safety and SecurityOccupant safety
Occupant safetyIn this section you will learn the most im-
portant facts about the restraint systems
of the vehicle.
The restraint systems are:
Seat belts
Emergency tensioning device
Airbags
Child seats
Child seat recognition
Lower anchors and tethers for children
(LATCH)
As independent systems their protective
effects work in conjunction with each oth-
er.The
1
indicator lamp in the instrument
cluster lights up
for about four seconds when you turn
the key in the starter switch to
position1 or press the KEYLESS-GO*
start/stop button once. It then goes
out briefly, lights up again and remains
lit until you start the engine.
for about four seconds when you start
the engine by turning the key or press-
ing the KEYLESS-GO* start/stop but-
ton.The restraint systems are fully operational
if the 1 indicator lamp is not lit when the
engine is running.
A malfunction in the system has been de-
tected, if the 1 indicator lamp:
fails to go out after approximately four
seconds.
does not come on at all.
comes on after the engine was started
or while driving.
For safety reasons, we strongly recom-
mend that you visit an authorized
Mercedes-Benz Center immediately to
have the system checked.
More information can be found in the
“Practical hints” section (
page 289).
iFor information on infants and children
traveling with you in the vehicle and re-
straint systems for infants and chil-
dren, see “Children in the vehicle”
(page 67).
iThe
1
indicator lamp lights up and
remains lit if the key is turned to posi-
tion 2 and left there or the
KEYLESS-GO* start/stop button is
pressed twice. The indicator lamp will
go out when you start the engine.
57 Safety and Security
Occupant safety
Airbags
Warning!
G
In the event that the 1 indicator lamp lights
up during driving or does not come on at all,
the SRS may not be operational. For your
safety, we strongly recommend that you vis-
it an authorized Mercedes-Benz Center im-
mediately to have the system checked;
otherwise the SRS may not be activated
when needed in an accident, which could re-
sult in serious or fatal injury, or it might de-
ploy unexpectedly and unnecessarily which
could also result in injury.
Improper work on the restraint systems, in-
cluding incorrect installation and removal,
can lead to possible injury through an unin-
tended activation of the SRS.
In addition, through improper work there is
a risk of rendering the SRS inoperative or
causing unintended airbag deployment.
W o r k o n t h e S R S m u s t t h e r e f o r e o n l y b e p e r -
formed by an authorized Mercedes-Benz
Center.
Warning!
G
Airbags are designed to reduce the potential
of injury and fatality in certain frontal im-
pacts (front airbags), side impacts (side im-
pact airbags and head protection window
curtain airbags) or rollovers (head protec-
tion window curtain airbags). However, no
system available today can totally eliminate
injuries and fatalities.
The activation of the SRS temporarily releas-
es a small amount of dust from the airbags.
This dust, however, is neither injurious to
your health, nor does it indicate a fire in the
vehicle. The dust might cause some tempo-
rary breathing difficulty for people with asth-
ma or other breathing trouble. To avoid this,
you may wish to get out of the vehicle as
soon as it is safe to do so. If you have any
breathing difficulty but cannot get out of the
vehicle after the airbag inflates, then get
fresh air by opening a window or door.
Warning!
G
To reduce the risk of injury when the front
airbags inflate, it is very important for the
driver and front passenger to always be in a
properly seated position and to wear your
seat belts.
For maximum protection in the event of a
collision always be in normal seated position
with your back against the seat backrest.
Fasten your seat belt and ensure that it is
properly positioned on your body.
Since the airbag inflates with considerable
speed and force, a proper seating and hands
on steering wheel position will help to keep
you at a safe distance from the airbag. Oc-
cupants who are unbelted, out of position or
too close to the airbag can be seriously in-
jured by an airbag as it inflates with great
force in the blink of an eye:
Sit properly belted in an upright position
with your back against the seat back-
rest.
62 Safety and SecurityOccupant safetyThe front passenger side impact airbag2
will only deploy if the system senses that
the front passenger seat is occupied.
The window curtain airbags fill up the area
between the A and C pillars (see arrows).
3Window curtain airbag
4Side impact airbags
Seat belts
The seat belt nonusage warning lamp
<
in the instrument cluster lights up and a
warning sounds for a short time when you
turn the SmartKey in the starter switch to
position2 or press the KEYLESS-GO* (if so
equipped) start/stop button twice and the
driver’s seat belt is not fastened.
After starting the engine, the seat belt non-
usage warning lamp blinks for a brief peri-
od to remind the driver and passengers to
fasten their seat belts.
The use of seat belts and infant and child
restraint systems is required by law in
most states and all Canadian provinces.
Even where this is not the case, all vehicle
occupants should have their seat belts fas-
tened whenever the vehicle is in motion.
For information on fastening seat belts,
see “Getting started” (
page 29).
iFor information on infants and children
traveling with you in the vehicle and re-
straint systems for infants and chil-
dren, see “Children in the vehicle”
(page 67).