2003 MERCEDES-BENZ E320 Program

152 Controls in detailAutomatic transmissionOne-touch gearshifting
Even with an automatic transmission you
can change the gears yourself when the
selector lever is in positionD.
Downshifting
Briefly press the selector lever to the
left in the D–direction.
The transmission will shift from the current
gear to the next lower gear. This action si-
multaneously limits the gear range of the
transmission (
page 153).Upshifting

Briefly press the selector lever to the
right in the D+direction.
The transmission will shift from the current
gear to the next higher gear as permitted
by the shift program. This action simulta-
neously extends the gear range of the
transmission.Canceling gear range limit

Press and hold the selector lever in the
D+direction until D reappears in the
tachometer display field.
The transmission will shift from the current
gear range directly to gear rangeD.
Shifting into optimal gear range

Press and hold the gear selector lever
in the D–direction.
The transmission will automatically select
the gear range suited for optimal accelera-
tion and deceleration. This will involve
shifting down one or more gears.
Warning!
G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of loss of control.
iTo avoid overrevving the engine when
the selector lever is moved to the
D–direction, the transmission will not
shift to a lower gear if the engine's
max. speed would be exceeded.

155 Controls in detail
Automatic transmission
Program mode selector switch
1Program mode selector switch
S Standard For regular driving
W Winter For winter driving

Press the program mode selector
switch repeatedly until the letter of the
desired shift program appears in the
speedometer display field
(page 121).
Select
Wfor winter driving:


The vehicle starts out in second
gear (both forward and reverse) for
gentler starts. This does not apply if
full throttle is applied or gear
range1 is selected.


Traction and driving stability are im-
proved on icy roads.


Upshifts occur earlier even when
you give more gas. The engine then
operates at lower rpms and the
wheels are less likely to spin.


The power transmission ratio for se-
lector lever positionR changes de-
pending on the program mode
selected (
W or
S).
Warning!
G
When leaving the vehicle always remove the
key from the starter switch, take the Smart-
Key with KEYLESS-GO* (if so equipped) with
you and lock the vehicle. Do not leave chil-
dren unattended in the vehicle, or with ac-
cess to an unlocked vehicle. Children could
move the selector lever from positionP,
which could result in an accident or serious
injury.
!Never change the program mode when
the selector lever is out of positionP. It
could result in a change of driving char-
acteristics for which you may not be
prepared.

238 Controls in detailUseful features
Roadside Assistance button•
Located below the center armrest cover is
the Roadside Assistance button•.
Press and hold the button for more
than 2 seconds.
A call to a Mercedes-Benz Roadside As-
sistance dispatcher will be initiated.
The button will flash while the call is in
progress. The message
ROADSIDE AS-
SISTANCE – CONNECTING CALL
will ap-
pear in the multifunction display.
When the connection is established, the
message
ROADSIDE ASSISTANCE –
CALL CONNECTED
appears in the multifunc-
tion display. The Tele Aid system will trans-
mit data generating the vehicle
identification number, model, color and lo-
cation (subject to availability of cellular
and GPS signals).
A voice connection between the Roadside
Assistance dispatcher and the occupants
of the vehicle will be established. When a
voice connection is established, the audio
system is muted and the message
TELE AID – ROADSIDE ASSISTANCE
CALL ACTIVE
appears in the multifunction
display.

Describe the nature of the need for as-
sistance.
The Mercedes-Benz Roadside Assistance
dispatcher will either dispatch a qualified
Mercedes-Benz technician or arrange to
tow your vehicle to the nearest authorized
Mercedes-Benz Center. For services such
as labor and/or towing, charges may ap-
ply. Refer to the Roadside Assistance man-
ual for more information.
These programs are only available in the
USA:


Sign and Drive services: Services such
as a jump start, a few gallons of fuel or
the replacement of a flat tire with the
vehicle spare tire are obtainable.


Remote Vehicle Diagnostics: This func-
tion permits the Mercedes-Benz Road-
side Assistance dispatcher to
download malfunction codes and actu-
al vehicle data.
Warning!
G
If you feel at any way in jeopardy when in the
vehicle (e.g. smoke or fire in the vehicle, ve-
hicle in a dangerous road location), please
do not wait for voice contact after you have
pressed the emergency button. Carefully
leave the vehicle and move to a safe loca-
tion. The Response Center will automatically
contact local emergency officials with the
vehicle’s approximate location if they re-
ceive an automatic SOS signal and cannot
make voice contact with the vehicle occu-
pants.

244 Controls in detailUseful features
Programming or reprogramming the in-
tegrated remote control
Turn key in the starter switch to
position1 or2.

Hold the end of the hand-held transmit-
ter of the device you wish to train
approximately 2 to 5 inches (5 cm to
12 cm) away from the surface of the in-
tegrated remote control located on the
inside rear view mirror, keeping the in-
dicator lamp in view.

Using both hands, simultaneously push
the hand-held transmitter button and
the desired integrated remote control
button. Do not release the buttons until
completing the next step.

The indicator lamp on the integrated
remote control will flash, first slowly
and then rapidly. The rapid flashing
lamp indicates successful program-
ming of the new frequency signal.

When the indicator lamp flashes rapid-
ly, release both buttons.
Warning!
G
When programming a garage door opener,
the door moves up or down.
When programming or operating the remote
control make sure there is no possibility of
anyone being harmed by the moving door.iCertain types of garage door openers
are incompatible with the integrated
opener. If you should experience diffi-
culties with programming the transmit-
ter, contact your authorized
Mercedes-Benz Center, or call
Mercedes-Benz Customer Assistance
Center (in the USA only) at
1-800-FOR-MERCedes, or Customer
Service (in Canada) at
1-800-387-0100.
iFor operation in the USA only:
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.

245 Controls in detail
Useful features

To program the remaining two buttons,
repeat the above steps.
Rolling code programming
To train a garage door opener (or other roll-
ing code devices) with the rolling code fea-
ture, follow these instructions after
completing the "Programming" portion of
this text. (A second person may make the
following training procedures quicker and
easier.)

Locate training button on the garage
door opener motor head unit. Exact location and color of the button
m a y v a r y b y g a r a g e d o o r op e n e r b r a n d .
If there is difficulty locating the trans-
mitting button, refer to garage door
opener operator’s manual.

Press "training" button on the garage
door opener motor head unit.
The "training light" is activated.
You have 30 seconds time to initiate the
following step.

Firmly press and release the pro-
grammed integrated remote control
transmit button.

Press and release same button a sec-
ond time to complete the training pro-
cess.
Some garage door openers may require
you to do this procedure a third time to
complete the training.

Confirm the garage door operation by
pressing the programmed button on
the integrated remote control transmit-
ter. Canadian programming
During programming, your hand-held
transmitter may automatically stop trans-
mitting.

Continue to press and hold the inte-
grated remote control transmitter but-
ton (refer to steps two through four in
the "Programming" portion) while you
press and re-press ("cycle") your
hand-held transmitter every two sec-
onds until the frequency signal has
been learned.
Upon successful training, the indicator
lamp will flash slowly and then rapidly
after several seconds.
iIf, after several attempts, you do not
successfully program the integrated re-
mote control device to learn the signal
of the hand-held transmitter, the ga-
rage door opener could be equipped
with the "rolling code feature".

378 Technical termsMenu
The control system displays are ar-
ranged in menus. Each menu contains
a number of commands for particular
systems. In the Audio menu, for exam-
ple, you will find the commands
SELECT RADIO STATION or
OPERATE CD
PLAYER
. Using commands you can di-
rectly change the settings for your ve-
hicle.
MON
(M
otor O
ctane N
umber)
The Motor Octane Number for gasoline
as determined by a standardized meth-
od. It is an indication of a gasoline's
ability to resist undesired detonation
(knocking). The average of both the
MON (Motor Octane Number) and
->RON (Research Octane Number) is
posted at the pump, also known as
ANTI-KNOCK INDEX.Multifunction display
The display field in the instrument clus-
ter used to present information provid-
ed by the control system.
Multifunction steering wheel
Steering wheel with buttons for operat-
ing the control system.
Overspeed range
Engine speeds within the red marking
of the tachometer dial. Avoid this en-
gine speed range, as it may result in se-
rious engine damage that is not
covered by the Mercedes-Benz Limited
Warranty.
Poly-V-belt drive
Drives engine-components (alternator,
AC compressor, etc.) from the engine.Power train
Collective term designating all compo-
nents used to generate and transmit
motive power to the drive axles, includ-
ing:


Engine


Clutch/torque converter


Transmission


Transfer case*


Drive shaft


Axle shafts/axles
Program mode selector switch
Used to switch the automatic transmis-
sion between standard operationS and
winter operationW.
Remote Vehicle Diagnostics
Transmission of vehicle data and cur-
rent location to the Mercedes-Benz
Customer Assistance Center for sub-
scribers to the Tele Aid service.

382 IndexAIRMATIC DC (Dual Control) 209
Alarm
Audible 72, 82
Canceling 82
Visual 82
Alarm system
Anti-theft 82
Alignment bolt (vehicle tool kit) 340, 375
Antiglare
Automatic 157
Antilock brake system (ABS) 375
Anti-theft alarm system
Arming 82
Canceling alarm 82
Disarming 82
Anti-theft systems 81
Anti-theft alarm system 82
Immobilizer 81
Tow-away alarm 82
Ashtray 231
AUDIO menu 126
Selecting radio station 127
Automatic antiglare for rear view
mirror 157Automatic central locking
Activating/deactivating (control
system) 142
Automatic climate control
Temperature sensor 27
Automatic climate control* 172
Adjusting air distribution 177
Adjusting air volume 166, 177
Air recirculation mode 178
Defrosting 178
Rear window defroster 169, 180
Residual heat utilization 182
Residual ventilation 182
Setting the temperature 176
Automatic headlamp mode 113
Automatic lighting control
Activating 116
Deactivating 116
Automatic locking when driving 99
Automatic transmission 151
Accelerator position 156
Emergency operation (Limp Home
Mode) 156
Gear ranges 153Gear selector lever position 154
Gear shifting malfunctions 156
Kickdown 156
One-touch gearshifting 152
Program mode selector switch 155
Selector lever position 151
Starting the engine 43
Winter program mode 155
B
BabySmart
TM
Compatible child seats 375
Self-test 68
BabySmart
TM airbag deactivation
system 67, 375
Backrest
Folding forward 220
Folding rearward 221
BAS 74, 375
Messages in display 297, 298
Batteries, SmartKey
Changing 329
Check lamp 87
Checking 88

386 IndexDoors
Message in display 323
Opening from inside vehicle 93
Opening from outside 87, 91
Downhill driving
Cruise control 195
Downshifting 152
Driving
General instructions 40
Problems 48
Safety systems 73
With Distronic* 206
Driving hints
SBC brake system 79
Driving safety systems
ABS 73
BAS 74
ESP 75, 376
SBC brake system 77
Driving systems 194
AIRMATIC DC 209
Cruise control 194
Distronic* 197
Driving safety systems 73
Vehicle level control 209
DTR see Distronic* 376Dual control
AIRMATIC DC 209
E
Easy-entry/exit
Message in display 310
Easy-entry/exit feature* 102
Activating 143
Interrupting movement 102, 143
Electrical fuses 352
Electrical system 363
Electronic Stability Program see ESP 75,
376
Emergency call system* 235
Emergency calls
Initiating an emergency call 237
With Tele Aid* 236
Emergency operation (Limp Home
Mode) 156
Emergency operations
Releasing trunk lid from inside 97
Remote door unlock 241
Sliding/pop-up roof* or panorama slid-
ing/pop-up roof* 331
Unlocking the vehicle 327Emergency tensioning device 377
Emergency tensioning device see
ETD 377
Ending
A call (telephone) 149
Engine 360
Starting 43
Starting with KEYLESS-GO* 44
Starting with the key 44
Turning off with the key 52
Engine number 376
Engine oil
Adding 263
Additives 368
Checking level 262
Display messages 299, 300
Filler neck 263
Messages in display 264, 300
Viscosity 376
ESP 75, 376
Switching off 76
Switching on 77
Warning lamp 288
ETD 377
Safety guidelines 59
Exterior lamp switch 112