2003 INFINITI G35 maintenance schedule

Schedule 2 Abbreviations: R = Replace, I = Inspect. Correct or replace if necessary. [ ]: Perform service at the mileage intervals onlyMAINTENANCE OPERATION MAINTENANCE INTERVAL
Perform at number of miles, kilometers or months,
whichever comes first. Miles x 1,000 7.5 15 22.5 30 37.5 45 52.5 60
(km x 1,000) (12) (24) (36) (48) (60) (72) (84) (96)
Months 6 12 18 24 30 36 42 48
EMISSION CONTROL SYSTEM MAINTENANCE
Engine oil RRRRRRRR
Engine oil filter (Use Part No. 15208 31U00 or 15208 65F00 or equivalent) RRRRRRRR
Air cleaner filter [R] [R]
EVAP vapor lines I* I*
Fuel lines I* I*
Drive belts See NOTE (1) I*
Engine coolant See NOTE (2) R*
Spark plugs (PLATINUM-TIPPED Type) Replace every 105,000 miles (169,000 km)
Fuel filter See NOTE (3)
Intake & exhaust valve clearance* See NOTE (4)
NOTE: (1) After 60,000 miles (96,000 km) or 48 months, inspect every 15,000 miles (24,000 km) or 12 months. Replace the drive belts if found damaged.
(2) After 60,000 miles (96,000 km) or 48 months, replace every 30,000 miles (48,000 km) or 24 months.
(3) Maintenance-free item (In-tank type fuel filter).
(4) If valve noise increases, inspect valve clearance.
* Maintenance items and intervals with ª*º are recommended by INFINITI for reliable vehicle operation. The owner need not perform such maintenance in order
to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are required.
9-8 Maintenance
Z 02.7.29/V35-D/V5.0
X

Schedule 2 Abbreviations: R = Replace, I = Inspect. Correct or replace if necessary.
MAINTENANCE OPERATION MAINTENANCE INTERVAL
Perform at number of miles, kilometers or months,
whichever comes first. Miles x 1,000 7.5 15 22.5 30 37.5 45 52.5 60
(km x 1,000) (12) (24) (36) (48) (60) (72) (84) (96)
Months 6 12 18 24 30 36 42 48
CHASSIS AND BODY MAINTENANCE
Brake lines & cables IIII
Brake pads & rotors IIII
Manual transmission gear oil or automatic transmission fluid &
differential gear oil See NOTE (1) IIII
Steering gear & linkage, axle & suspension parts I I
Tire rotation See NOTE (2)
Exhaust system II
In-cabin microfilter RRRRNOTE: (1) Using automatic transmission fluid other than Genuine Nissan ATF Matic Fluid J will cause deterioration in driveability and automatic transmission
durability, and may damage the automatic transmission, which is not covered by the INFINITI new vehicle limited warranty.
(2) Refer to ªTire rotationº under the ªGeneral maintenanceº heading earlier in this section.
Maintenance
9-9
Z 02.7.29/V35-D/V5.0
X

EXPLANATION OF MAINTENANCE
ITEMS Additional information on the following
items with ª*º is found in the ª8. Do-it-
yourselfº section.
Emission control system
maintenance Drive belts*: Check drive belts for wear, fray-
ing or cracking and also for proper tension.
Replace the drive belts if found damaged.
Air cleaner filter: Under normal driving con-
ditions, the air cleaner filter should be replaced
in accordance with the maintenance schedule.
However, driving the vehicle in dusty areas
may cause more rapid clogging of the element.
Consequently, the element may have to be
replaced more frequently.
EVAP vapor lines: Check vapor lines and
connections for failure or looseness. If leaks
are found, replace them.
Fuel lines: Check the fuel hoses, piping and
connections for leaks, looseness or deteriora-
tion. Replace any parts if they are damaged.
Engine coolant*: Drain and flush the cooling
system.
Engine oil & oil filter*: Under normal driving conditions, the engine oil and oil filter should
be replaced in accordance with the mainte-
nance schedule. However, under severe driv-
ing conditions, they may have to be replaced
more frequently.
Spark plugs*: Replace with new plugs having
the correct heat range.
Chassis and body maintenance Brake lines & cables: Check the brake lines
and hoses (including brake booster vacuum
hoses, connections & check valve) and park-
ing brake cables for proper attachment, leaks,
cracks, chafing, abrasion, deterioration, etc.
Brake pads & rotors: Check these and the
other neighboring brake components for wear,
deterioration and leaks. Under severe driving
conditions, they may have to be inspected
more frequently.
Automatic transmission fluid*: Using auto-
matic transmission fluid other than Genuine
Nissan ATF Matic Fluid J will cause deteriora-
tion in driveability and automatic transmission
durability, and may damage the automatic
transmission, which is not covered by the
INFINITI new vehicle limited warranty. If
checking or replacement is required, we rec-
ommend your INFINITI retailer for servicing.
Under severe driving conditions, the fluid should be replaced at the specified interval.
Manual transmission oil & differential gear
oil*: Check the oil level and visually inspect for
signs of leakage.
Under severe driving conditions, the oil should
be replaced at the specified interval.
Steering gear & linkage, axle & suspension
parts: Check for damage, looseness and leak-
age of oil or grease. Under severe driving
conditions, more frequent inspection should be
performed.
Exhaust system: Visually check the exhaust
pipes, muffler, and hangers for proper attach-
ment, leaks, cracks, chafing, abrasion, dete-
rioration, etc. Under severe driving conditions,
inspection should be performed more fre-
quently.
In-cabin microfilter: Under normal condi-
tions, this microfilter should be replaced in
accordance with the maintenance schedule.
However, in some situations, the microfilter
may clog more rapidly (depending on the air
conditioner's working environment). If this hap-
pens, the air flow may decrease, or the win-
dows may fog up easily when the air condi-
tioner is in use, the microfilter should be
replaced immediately at your INFINITI retailer.
9-10 Maintenance
Z 02.7.29/V35-D/V5.0
X

condition; check for improper tongue load,
overload, worn suspension or other pos-
sible causes of either condition.
O Always secure items in the trailer to prevent
load shifts while driving.
O Be certain your rear view mirrors conform to
all federal, state or local regulations. If not,
install any mirrors required for towing be-
fore driving the vehicle.
Trailer towing tips In order to gain skill and an understanding of
the vehicle's behavior, you should practice
turning, stopping and backing up in an area
which is free from traffic. Steering stability, and
braking performance will be somewhat differ-
ent than under normal driving conditions.
O Always secure items in the trailer to prevent
load shift while driving.
O Avoid abrupt starts, acceleration or stops.
O Avoid sharp turns or lane changes.
O Always drive your vehicle at a moderate
speed.
O Always block the wheels on both vehicle
and trailer when parking. Parking on a
slope is not recommended; however, if you
must do so, and if your vehicle is equipped with automatic transmission, first apply the
parking brake and block the wheels, and
then move the transmission selector lever
into the P (Park) position. If you move the
selector lever to the P (Park) position be-
fore blocking the wheels and applying the
parking brake, the transmission may be
damaged.
O When going down a hill, shift into a lower
gear and use the engine braking effect.
When ascending on a long grade, down-
shift the transmission to a lower gear and
reduce speed to reduce chances of engine
overloading and/or overheating.
O If the engine coolant rises to an extremely
high temperature when the air conditioning
system is on, turn off the air conditioner.
Coolant heat can be additionally vented by
opening the windows, switching the fan
control to high and setting the temperature
control to the HOT position.
O Trailer towing consumes more fuel than
normal circumstances.
O Avoid towing a trailer for the first 500 miles
(800 km).
O Have your vehicle serviced more often than
at intervals specified in the recommended
maintenance schedule. O When making a turn, your trailer wheels will
be closer to the inside of the turn than your
vehicle wheels. To compensate for this,
make a larger than normal turning radius
during the turn.
O Crosswinds and rough roads will adversely
affect vehicle/trailer handling, possibly
causing vehicle sway. When being passed
by larger vehicles, be prepared for possible
changes in crosswinds that could affect
vehicle handling. If swaying does occur,
firmly grip the steering wheel, steer straight
ahead, and immediately (but gradually) re-
duce vehicle speed. This combination will
help stabilize the vehicle. Never increase
speed.
O Be careful when passing other vehicles.
Passing while towing a trailer requires con-
siderably more distance than normal pass-
ing. Remember the length of the trailer
must also pass the other vehicle before you
can safely change lanes.
O To maintain engine braking efficiency and
electrical charging performance, do not use
sixth gear (manual transmission) or fifth
position (automatic transmission).
O Avoid holding the brake pedal down too
long or too frequently such as on long
down-hill sections of road. This could cause
10-18 Technical and consumer information
Z 02.7.29/V35-D/V5.0
X

the brakes to overheat, resulting in reduced
braking efficiency. Shift down and use en-
gine braking.
When towing a trailer, change transmission
oil more frequently.
See ªPeriodic maintenance schedulesº in
the ª9. Maintenanceº section. Shift down
and use engine braking. DOT (Department Of Transportation) Quality
Grades: All passenger car tires must conform
to federal safety requirements in addition to
these grades.
Quality grades can be found where applicable
on the tire sidewall between tread shoulder
and maximum section width. For example:
Treadwear 200 Traction AA Temperature A
Treadwear Treadwear grade is a comparative rating
based on tire wear rate when tested under
controlled conditions on specified government
test courses. For example, a tire graded 150
would wear one and a half (1-1/2) times as well
on the government course as a tire graded
100. However, relative tire performance de-
pends on actual driving conditions, and may
vary significantly from the norm due to varia-
tions in driving habits, service practices and
differences in road characteristics and climate.
Traction AA, A, B and C The traction grades, from highest to lowest,
are AA, A, B, and C. Those grades represent
the tire's ability to stop on wet pavement as
measured under controlled conditions on
specified government test surfaces of asphalt and concrete. A tire marked C may have poor
traction performance.
WARNING The traction grade assigned to your ve-
hicle tires is based on straight-ahead
braking traction tests, and does not in-
clude acceleration, cornering, hydro-
planing, or peak traction characteristics.
Temperature A, B and C Temperature grades are A (the highest), B,
and C. They represent a tire's resistance to
heat build-up, and its ability to dissipate heat
when tested under controlled conditions on a
specified indoor laboratory test wheel. Sus-
tained high temperature can cause tire mate-
rial to degenerate, reducing tire life. Excessive
temperatures can lead to sudden tire failure.
Grade C corresponds to a performance level
which all passenger car tires must meet under
the Federal Motor Vehicle Safety Standard No.
109. Grades A and B represent higher levels of
performance on laboratory test wheels than
the minimum required by law.UNIFORM TIRE QUALITY
GRADING
Technical and consumer information
10-19
Z 02.7.29/V35-D/V5.0
X

Vanity mirror light ...................................... 2-36
Warning/indicator lights and audible
reminders ........................................... 2-9, 2-11
Xenon headlights ..................................... 2-17
Lights, Exterior and interior light
replacement .................................................... 8-26
Loading information (See vehicle loading
information) ................................................... 10-14
Lock
Door locks ................................................... 3-3
Glove box lock........................................... 2-27
Power door lock .......................................... 3-3
Trunk lid lock opener lever........................ 3-10
M
Maintenance
Battery ....................................................... 8-13
Chassis and body...................................... 9-10
Emission control system ........................... 9-10
General maintenance .................................. 9-2
Inside the vehicle ........................................ 9-3
Maintenance precautions ............................ 8-2
Outside the vehicle...................................... 9-3
Periodic maintenance schedules ................ 9-5
Seat belt maintenance .............................. 1-32
Under the hood and vehicle ........................ 9-4
Manual front seat adjustment ........................... 1-2
Map light ......................................................... 2-35
Meters and gauges ........................................... 2-3
Mirror
Automatic anti-glare inside mirror ............. 3-17
Outside mirror control................................ 3-18
Outside mirrors .......................................... 3-18 N
Net
Cargo net................................................... 2-29
Small cargo net (Sedan for Canada) ........ 2-30
New vehicle break-in ...................................... 5-17
Nissan vehicle Immobilizer System ................ 2-13
O
Odometer .......................................................... 2-4
Oil
Capacities and recommended fuel/lubricants/
fluids .......................................................... 10-2
Changing engine oil and filter ..................... 8-8
Checking engine oil level ............................ 8-7
Engine oil..................................................... 8-7
Engine oil viscosity .................................... 10-5
Outside mirror control ..................................... 3-18
Outside mirrors ............................................... 3-18
Overheat, If your vehicle overheats................ 6-10
P
Parking
Brake check............................................... 8-18
Parking brake check.................................. 5-14
Parking brake operation ............................ 5-14
Parking on hills .......................................... 5-14
Parking/parking on hills .................................. 5-18
Periodic maintenance schedules ...................... 9-5
Phone, Car phone or CB radio ....................... 4-18
Pocket (Manual transmission model) ............. 2-25 Power
Power door lock .......................................... 3-3
Power front seat adjustment ....................... 1-4
Power outlet .............................................. 2-23
Power steering fluid................................... 8-10
Power steering system .............................. 5-19
Power windows ......................................... 2-31
Pre-tensioner seat belt system ....................... 1-22
Precautions
Audio operation precautions ....................... 4-8
Braking precautions................................... 5-19
Cruise control precautions ........................ 5-15
Maintenance precautions ............................ 8-2
On child restraints ..................................... 1-33
On seat belt usage .................................... 1-25
Precautions on supplemental restraint
system ....................................................... 1-11
Precautions when starting and driving ........ 5-2
Push starting ..................................................... 6-9
R
Radio
Car phone or CB radio .............................. 4-18
FM-AM radio operation ............................. 4-11
Satellite radio antenna .............................. 4-18
Satellite radio operation ............................ 4-12
Satellite radio reception............................... 4-8
Steering audio control ............................... 4-17
Readiness for inspection/maintenance (I/M) test
(US only) ....................................................... 10-21
Rear armrest pocket ....................................... 2-29
Rear door lock, Child safety rear door lock...... 3-5
Rear personal light ......................................... 2-36
11-4
Z 02.7.29/V35-D/V5.0
X