2003 Hyundai Coupe heating

CONTROLS AND EQUIPMENT
1- 30 SB215F1-E TACHOMETER
SB215B1-E ENGINE COOLANT TEMPERATURE GAUGE engine is hot may cause hot water and steam to be ejected from the radiator resulting inburns and scalding. The radiator cap mustonly be removed when the engine has cooled.Do not add cold water to a hot engine to avoidthe possibility of engine damage. The use ofplain water in the cooling system is not rec-ommended since the aluminium componentsof the cooling system require the use of acorrosion inhibitor found in the recommendedEthylene Glycol type anti freeze solutions.
The engine coolant temperature gauge indicatesthe engine coolant temperature and will, undernormal circumstances, give an indication in the"Normal" or centre portion of the scale. Shouldthe indication move into the upper or "Hot" por-tion of the scale, engine overheating is indicated.Under these circumstances, the vehicle shouldbe brought to rest as soon as is safe to do so andthe engine turned off. Once the engine has cooledsomewhat, the coolant level and the condition ofthe generator/water pump drive belt should bechecked. If the cause of the overheating cannotbe readily established, the assistance of aHyundai dealer should be sought. WARNING: The engine cooling system is pressurizedand removal of the radiator cap when the The tachometer registers the speed of the enginein revolutions per minute (R.P.M.). CAUTION: The maximum safe engine operating speed isindicated by the white zone of the tachometerscale. The engine should not be operatedbeyond the beginning of this zone or seriousengine damage may result.
SB215C1-E SPEEDOMETER
The speedometer indicates the vehicle speed in both miles and kilometres per hour.
HGK132HGK131A
HGK130B

CONTROLS AND EQUIPMENT
1- 36 SB250A1-E HEATED REAR WINDOW
SB240A1-EHAZARD WARNING SYSTEM The hazard warning system should be used whenever it becomes necessary to stop the carin a hazardous location. The hazard warningsystem is operated by depressing the switch atwhich time all turn signal lamps will flash simul-taneously and the turn signal warning lampslocated within the instrument cluster will flashsimultaneously.The hazard warning system may be turned off bydepressing the switch again. To operate the heated rear window depress theswitch shown. The heated rear window will auto-matically turn off after 15 minutes or when theignition is turned off.The system may be turned off manually by de-pressing the switch again. CAUTION: The inside of the rear windscreen shouldnever be cleaned with a hard or sharp imple-ment since damage to the heating elementmay occur. The glass should only be cleanedwith a soft cloth or chamois leather with theuse only of a mild detergent or proprietaryglass cleaner where necessary. Only hori-zontal movement of the cloth should be madewhen cleaning the glass and care should beexercised to ensure that the heating elementsare not damaged by rings or jewellery whilstthe glass is being cleaned.
o In icy or snowy weather, ensure that the
wiper blades are not frozen to the glassprior to operating the wipers.
HGK046-D
B350A01O-EAT Hatchback door Wiper And Washer Switch
1. :The washer fluid will be sprayed onto the
rear window and the wiper operates while the rear window wiper barrel is placed inthis position.
2.OFF3.INT :To use the intermittent wiper feature,
place the rear window wiper barrel in the"INT" position.
4.ON :When the point indicates the "ON", the
rear window wiper operates continuously.
HGK140B380A01GK
A Type
B Type

CONTROLS AND EQUIPMENT1- 51
B710A01GK-EAT HEATING AND COOLING CONTROL
1. Side defrost nozzle
2. Side Ventilator
3. Centre Ventilator
4. WindScreen Defrost VentilatorHGK001A-D
1
2
3
1
2 B710A01S-AAT VENTILATIONTo operate the ventilation system:
o Set the air intake control on "Fresh" mode
( ).
o To direct all intake air to the dashboard vents, set the airflow control to "Face".
o Adjust the fan speed control to the desired speed.
o Set the temperature control between "Cool" and "Warm".
B710C01S-AAT SIDE VENTILATORThe side ventilators are located on each side of dashboard. To change the direction of the airflow, move the knob in the center of the vent up-and-down and side-to-side. The side vent knobscontrol the amount of outside air entering thevehicle through the side vents. The vents areopened when the vent knob is moved to the upposition. The vents are closed when the ventknob is moved to the down position. Keep thesevents clear of any obstructions.
B710B01S-DAT CENTRE VENTILATOR The centre ventilators are located in the middle of the dashboard. The direction of air flow from thevents in the centre of the dashboard is adjust-able.To control the direction of the air flow, move theknob in the centre of the vent up-and-down andside-to-side.4

CONTROLS AND EQUIPMENT
1- 52
HGK002
B670A01GK-GAT ROTARY TYPE (Not all models)
This control is used to adjust the degree of heating or cooling desired.B670E02A-AAT Temperature ControlCool
Warm
B670B01A-AAT Fan Speed Control (Blower Control)HGK006
This is used to turn the blower fan on or off and to select the fan speed.This blower fan speed, and therefore the volumeof air delivered from the system, may be con-trolled manually by setting the blower controlbetween the "1" and "4" positions.
123
456
1. Air Conditioning switch
2. Air intake control switch
3. Rear window defroster switch
4. Air flow control switch
5. Fan speed control switch
6. Temperature control switch HGK007

CONTROLS AND EQUIPMENT1- 53
HGK016B670D01GK-EAT Air Flow Control This is used to direct the flow of air. Air can be directed to the floor, dashboard outlets, orwindscreen. Five symbols are used to representFace, Bi-Level, Floor, Floor-Defrost and Defrostair position.HGK005
B670C01FC-EAT Air Intake Control This is used to select fresh outside air or recircu- lating inside air.To change the air intake control mode, (Freshmode, Recirculation mode) push the control but-ton. FRESH MODE ( ) : The indicator light on the button goes off when the air intake control isfresh mode. RECIRCULATION MODE ( ): The indicator light on the button is illuminated when the airintake control is recirculation mode. With the "Fresh" mode selected, air enters the vehicle from
the outside and is heated or cooled
according to the function selected. With the "Recirculation" mode selected, air fromwithin the passenger compartment
will be drawn
through the heating system and heated or cooledaccording to the function selected. NOTE:
o It should be noted that prolonged opera- tion of the heating in "Recirculation" modewill give rise to fogging of the windscreenand side windows and the air within thepassenger compartment will become stale.In addition, prolonged use of the air con-ditioning with the "Recirculation" modeselected may result in the air within thepassenger compartment becoming exces-sively dry.
o When the ignition switch is turned "ON" the air intake control will change to "Re-circulation" mode (regardless of switchposition). It is normal operation.

CONTROLS AND EQUIPMENT1- 55
B690A01S-AAT HEATING CONTROLSFor normal heating operation, set the air intake control to the "Fresh" position and the air flowcontrol to "Floor". For faster heating, the air intake control should be in the "Recirculation" position. If the windows fog up, move the air flow control to the "Def" (defroster) position. (The A/C will be onautomatically and it will be changed to "Fresh"mode.) For maximum heat, move the temperature con- trol to "Warm".
B730A01FC-EAT Operation Tips
o To keep dust or unpleasant fumes from enter-
ing the car through the ventilation system, temporarily set the air intake control at "Recir-culation". Be sure to return the control to"Fresh" when the irritation has passed tokeep fresh air in the vehicle. This will helpkeep the driver alert and comfortable.
o Air for the heating/cooling system is drawn in through the grilles just ahead of the wind-screen. Care should be taken that these arenot blocked by leaves, snow, ice or otherobstructions.
o To prevent interior fog on the windscreen, set the air intake control to the fresh air ( )position and fan speed to the desi-red posi-tion.
NOTE:When the A/C is operated continuously onthe floor-defrost level (
) or defrost level
(), it may cause fog to form on the exterior
windscreen by the temperature differential. At this time set the air flow control to the facelevel position (
)and fan speed control to the
low position.
Use the heating/ventilation system to defrost or defog the windscreen: To remove the interior fog on the windscreen;
o Set the air flow control to the defrost (
)
position. (The A/C will be on automatically and it will be changed to "Fresh" mode.)
o Set the temperature control at the desired position.
o Set the fan speed control between "1" and "4" position.
To remove the frost or exterior fog on thewindscreen;
o Set the air flow control to the defrost (
)
position. (The A/C will be on automatically and it will be changed to "Fresh" mode.)
o Set the temperature control to the warm.
o Set the fan speed control to position "3" or "4". B720A01FC-EAT DEFROSTING/DEFOGGING
HGK002

CONTROLS AND EQUIPMENT
1- 56
B740A01S-AAT AIR CONDITIONING SYSTEM (Not all models)Air Conditioning Switch
HGK018
The air conditioning is turned on or off by pushing the A/C button on the heating/air conditioningcontrol panel.
HGK002
B740B01S-AAT Air Conditioning Operation Cooling To use the air conditioning to cool the interior:
o Set the side vent control to "OFF", to shut off outside air entry.
o Turn on the fan control switch.
o Turn on the air conditioning switch by pushing in on the switch. The air conditioning indicator lightshould come on at the same time.
o Set the air intake control to "Fresh" mode ( ).
o Set the temperature control to "Cool". ("Cool" provides maximum cooling. The temperaturemay be moderated by moving the controltoward "Warm".)
o Adjust the fan control to the desired speed. For greater cooling, turn the fan control toone of the higher speeds or temporarilyselect the "Recirculation" position on the airintake control.B740C01S-AAT Dehumidified HeatingFor dehumidified heating:
o Turn on the fan control switch.
o Turn on the air conditioning switch. The airconditioning indicator light should come on atthe same time.
o Set the air intake control to "Fresh" mode ( ).
o Set the air flow control to "Face".
o Adjust the fan control to the desired speed.
o For more rapid action, set the fan at one of the higher speeds.
o Adjust the temperature control to provide the desired amount of warmth.

CONTROLS AND EQUIPMENT1- 57
B970A01Y-EAT AUTOMATIC HEATING AND COOLING CONTROL SYSTEM (Not all models)Your Hyundai is equipped with an automatic heating and cooling control system controlled by simply setting the desired temperat
ure.
B970B01GK-EATHeating and Cooling Controls TYPE A (Without Air Quality System) TYPE B (With Air Quality System)
1. Temperature Control Button
2. Defroster Switch
3. Display Window
4. Air Conditioning Switch
5. Rear Window Defroster Switch
6. Fan Speed Control Switch 7. Air Flow Control Switch
8. AUTO (Automatic Control)Switch
9. OFF Switch
10. Air lntake Control Switch
11. Ambient Switch
12. Air Quality System Switch (Not all models)HGK004
HGK003
1 235
4 6
78 9 10 11 1
2
3
4 5
6
78 910 1211