2003 HONDA CIVIC v tec

Exterior Trim
\
Rear License Trim Replacement
NOTE: Put on gloves to protect your hands.
1. Remove the hatch lower trim panel (see page 20-
2. On inside the hatch. remove the bolts securing the
rear license trim (A) and hatch lock cylinder (B).
Fastener Locations
> : Bolt,2
-)
6x1.0mm9.8 N.m (1.0 kgf.m,7.2lbf.ftl
20-98
3. From inside the hatch, release the clips (A, B)while
holding the rear license trim (C), then remove lhe
trim, Take care not to scratch the hatch.
Fastener Locations
A>:Clip,2 B>:Clip.2
\!-
cHl €:t+
Installthe trim in the reverse order of removal, and
note these rtems:
. Replace any damaged clips.. Push the clip portions into place securely.
4.

Hatch Spoiler Replacement
NOTE: Put on gloves to protect your hands.
'l. Remove the hatch upper trim (see page 20-53).
2. Remove the high mount brake light (see page 22-
82).
3. From inside the hatch, remove the bolts {A} and
nuts (B).
Fastener Locaiions
A>: Bolt,2 Bar Nut,
fi'f$t-- /,fluLt* v_/
5x1.0mm9.8Nm(1.0 kgf.m.7.2 lbf.ft)
$.A
4. From inside the hatch, release the clips, whilepulling the hatch spoiler (A) away, and release the
fasteners (B), then remove the spoiler. Take care
not to scratch the body.
Fastener Locations
>: Clip. 2
t
Installthe spoiler in the reverse order of removal,
and note these items:
Replace any damaged clips.
Replace any damaged fasteners. Before
installing the fastener to the spoiler, clean the
spoiler bonding surface with a sponge
dampened in alcohol. Glue the fastener with
adhesive tape (3M 5671, or equivalent)to the
spoiler.
Push the clip and fastener portions into place
securely.
5.
20-99

Exterior Trim
Emblem Replacement
NOTE: When removing the emblem, take care not to scratch the body.
1. To remove the front "H" emblem and front type emblem, remove the front bumper (see page 20-85)
2. Clean the bonding surface with a sponge dampened in alcohol. After cleaning, keep oil, grease, and water from
getting on the surface.
3. Apply the emblem, where shown.
. When installing the side i-VTEC emblem on the body, align the application tape with the edge of the wheel arch,
then press the emblem into place, and remove the application tape.. '03 model: When installing the LEV emblem on the quarter glass, align the application tape with the edge of the
black ceramic and alignment mark on the quarter glass, then press the emblem into place, and remove the
application tape.
FRONT TYPE EMBLEM
FBONT "H" EMBLEM
FRONT "H" EMBLEM BASEFBONT GRILLE
PUSH NUTS
i
SCREWS
FRONT Si EMBLEM PLATE
PINS
20-100
FRONT GRILLEFRONT GRILLE

LEV EMBLEM(Left side only)('03 model)
SIDE |-VTEC EMBLEM
Unit: mm {in.lAdhesive tape: 3M 4213E, o. equivalentThickness:0.8 mm (0.03 in.)
REAR CIVIC EMBLEM
REAR VERSION EMBLEM
REAR "H" EMBLEM
APPLICATION TAPE Edoe ol the black ceramic.
HATCH LINE
Align.
REAR LICENSETRIM REAR si EMBLEM
LEV EMBLEMOnto inside faceof the guarter glass.
REAR SiR EMBLEM
, ilg(1.93)=-t
50
CIVIC EMBLEMEdge ofthehatch.
SIDE i-VTEC EMBLEM
{'!,9?)
SIDE i.WECEMBLEM
ADHESIVE TAPEEdge of thehatch.
Right Side:63 (2.5)
F.l^6 ^l rh-
.=4,
Li.Est y'
BODYLINE
wheelarch.
112
BODYLINEo"f,r,ao.o" (5'5s)Edge of thewheel arch.APPLICATIONTAPETAPE
REAR "H'' EMBLEM
(Canada)
3411.3)
.,!!ll,'ntI (1.s31
Left Side:
. 114 (4.49)
4. After installing the front "H" enblem and front type emblem, reinstall the front bumper.
20-101

Fenderwell
(Fuel Pipe Protector Replacement
1.Remove the clips, then remove the fuel pipe
protector (A). Take care not to scratch the body.
Fastener Locations
> : Clip, 4
4
Installthe protector in the reverse order of removal,
and note these items:
. Replace any damaged clips.. Push the clips into place securelv.
20-104
Rear Air Outlet Replacement
1. Remove the rear bumper (see page 20-86).
Installthe air outlets by pushing on the hook
portions untilthe hooks snap into place.
rne rear atr
the body.

Openers
Hood Opener Cable Replacement
NOTE:. Put on gloves to protect your hands.. Take care not to scratch the body and related parts.
l. Remove these items:
. Front bumper (see page 20-85). Front inner fender, leftside(seepage20-102). Kick panel, left side (see page 20-50)
2. Disconnect the hood openercable (A) from the hood latch {B) (see
remove the hood release handle (D)from the body.
Fastener Locations
C >:Bolt,2 E >:Clip,3
page 20-108), and remove the bolts (C), then
6x1.0mm9,8 N.m11.0 kgl.m, 7.2 lbl.ft)
@m
4.
Using a clip remover, detach the clips (E), and remove the grommet (F)from the body, then remove the hood
opener cable from the vehicle. Take care not to bend the cable.
Installthe cable in the reverse order of removal, and replace any damaged clips.
l,.t'.
W:"
20-106

2.
5.
Fuel Fill Door Opener Cable Replacement
SRS components are located in this area. Review the SRS component locations (see page 23-13) and the precautions
and procedures (see page 23-14) in the SRS section before performing repairs or service.
NOTE;. Put on gloves to protect your hands.. Take care notto scratch the body and related parts.
1. Remove these items from the left side of the vehicle:
. Door silltrim {see page 20-50). Rear side trim panel (see page 20-51)
Pullthe carpet back as necessary (see page 20-55).
Disconnect the fuel fill door opener cable (A) from the opener (B) (see step 3 on page 20-109).
Fastener Locations
C >:Cushiontape, 1 D >: Clip, 1E > : Clip, 2
4. KCmodel: Removethe left middle floor cross-member gusset (see page 20-113).
5. Remove the cushion tape {C), and release the cable from the clips (D, E).
6. Removethefuel fill doorlatch (F)fromthe bodybyturning it90'.
7. Remove the fuel fill door opener cable from the vehicle. Take care not to bend the cable
8. Install theopenercableinthereverseorderofremoval,replacethecushiontape,andreplacetheclipifitis
oamageo.
20-107

Openers
Hood Latch Replacement
NOTE:. Put on gloves to protect your hands.. Take care not to scratch the body.
1. Remove the bolts, then remove the hood latch (A)
from the body.
Fastener Locations
> i Bolt, 3
Disconnect the hood opener cable (B) from the
hood latch. Take care not to bend the cable.
--------------'6x1.0mm9.8 N.m (1.0 kgf.m, 7.2lbf.ft)
20-108
Installthe hood latch in the reverse order of
removal, and note these items:
. Apply multipurpose grease to each location of
the hood latch indicated by the arrows.. Make sure the hood opener cable is connected
properly.
. Make sure the cable actuates the latch before you
close the hood,. Adjustthe hood latch alignment (see step 3 onpage 20-87).. Make sure the hood opens properly and locks
securely.