2003 HONDA ACCORD Check system

µ
µ
Ø Ø Ø Ø Ø ØØØØØØØØØ Ø ØØØØØØØ
ÌÌ

6-cylinder Models
Maint enance256
Canadian Owners
U.S. Owners A, B, C, D
AB C
D
Use the Maintenance Schedule for Severe Conditions.
Refer to page to determine which schedule to use.
Service at the indicated distance or time, whichever comes first. Do the items in as required for each distance/time.
7,500 mi/12,000 km
15,000 mi/24,000 km/1 yr
22,500 mi/36,000 km
30,000 mi/48,000 km/2 yrs
37,500 mi/60,000 km
3yrs
45,000 mi/72,000 km/3 yrs
52,500 mi/84,000 km
60,000 mi/96,000 km/4 yrs
67,500 mi/108,000 km
75,000 mi/120,000 km/5 yrs
82,500 mi/132,000 km
6yrs
90,000 mi/144,000 km/6 yrs
97,500 mi/156,000 km
105,000 mi/168,000 km/7 yrs
112,500 mi/180,000 km
120,000 mi/192,000 km/8 yrs
120,000 mi/192,000 km/10 yrs,
then replace every 60,000mi/
96,000 km/5 yrs
120,000 mi/192,000 km/6 yrs,
then replace every 90,000mi/
144,000 km/5 yrs Do items in A.
Do items in A, B.
Do items in A.
DoitemsinA,B,C.
Do items in A.
Replace brake fluid (independent of mileage).
Do items in A, B.
Do items in A.
DoitemsinA,B,C.
Do items in A.
Do items in A, B.
Do items in A. Replace brake fluid (independent of mileage).
DoitemsinA,B,C.
Do items in A.
DoitemsinA,B,D.
Do items in A.
DoitemsinA,B,C. Replace engine coolant.
Replace automatic transmission fluid. Replace engine oil.
Rotate tires (follow pattern on page 306).
Replace engine oil filter.
Inspect front and rear brakes.
Check parking brake adjustment.
Inspect tie rod ends, steering gear box, and boots.
Inspect suspension components.
Inspect driveshaft boots.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks.
Inspect exhaust system.
Inspect fuel lines and connections.
Inspect drive belt.
Replace air cleaner element.
Replace dust and pollen filter.
Inspect valve clearance.
Replace spark plugs.
Replace timing belt and inspect water pump.
See information on maintenance and emissions warranty, last
column, page .
Check engine oil and coolant at each fuel stop.
Check and adjust valve clearance, cold engine, only if noisy.
248
NOTE::
249
Maintenance Schedule for Normal Conditions (listed by distance/time)
——yy
(yy

µ
Ì
Î Î Î
Î
Ì Ì
CONT INUED
6-cylinder Models
Maint enance257
Visually inspect the following items:
Service at the indicated distance
or time whichever comes first.
miles x 1,000
km x 1,000
months
Every 3,750 miles (6,000 km) or 6 months
Every 15,000 miles (24,000 km) (Use normal schedule except in dusty conditions) Check oil and coolant at each fuel stop
At 120,000 miles (192,000 km) or 10 years,
then every 60,000 miles (96,000 km) or 5 years
Inspect every 105,000 miles (168,000 km), otherwise adjust only if noisy
152412
304824457236
60964875
120 60 90
144
72 105168
84 120192
96
Replace engine oil, and oil filter
Check engine oil and coolant
Replace air cleaner element
Inspect valve clearance
Replace spark plugs
Replace timing belt and inspect water pump
Inspect drive belt
Replace engine coolant
Replace transmission fluid
Inspect front and rear brakes
Replace brake fluid
Check parking brake adjustment
Replace dust and pollen filter
Lubricate all hinges, locks and latches
Rotate tires (Check tire inflation and condition at
least once per month)
Tie rod ends, steering gear box, and boots
Suspension components
Driveshaft boots
Brake hoses and lines (including ABS)
All fluid levels and condition of fluids
Exhaust system
Fuel lines and connections
Lights and controls, vehicle underbody Every 7,500 miles (12,000 km) or 6 months
Every 3 years (independent of mileage)
Rotate tires every 7,500 miles (12,000 km)
Every 7,500 miles (12,000 km) or 6 months
See information on maintenance and emissions warranty, last column, page .
See timing belt on page for replacement information under special driving conditions.
See dust and pollen filter on page for replacement information under special driving conditions.
:
1:2: A/T
300 249
302
1
2
Maintenance Schedule for Severe Conditions
——y

y
(yy

µ
µ
Ø Ø Ø ØØØØØ Ø ØØØØØØØØØØØØØ
ÌÌ Î
Î
Ì
Î Î
6-cylinder Models
Maint enance258
Canadian Owners
U.S. Owners A, B, C, D, E
AB C
D E
Use the Maintenance Schedule for Severe Conditions.
Refer to page to determine which schedule to use.
3,750 mi/6,000 km
7,500 mi/12,000 km
11,250 mi/18,000 km
15,000 mi/24,000 km/1 yr
18,750 mi/30,000 km
22,500 mi/36,000 km
26,250 mi/42,000 km
30,000 mi/48,000 km/2 yrs
33,750 mi/54,000 km
37,500 mi/60,000 km
41,250 mi/66,000 km
3yrs
45,000 mi/72,000 km/3 yrs
48,750 mi/78,000 km
52,500 mi/84,000 km
56,250 mi/90,000 km
60,000 mi/96,000 km/4 yrs
60,000 mi/96,000 km/4 yrs,
then replace every 30,000mi/
48,000 km/2 yrs
63,750 mi/102,000 km
67,500 mi/108,000 km
71,250 mi/114,000 km
75,000 mi/120,000 km/5 yrs
78,750 mi/126,000 km Do item in A.
Do items in A, E.
Do item in A.
DoitemsinA,B,E.
Do item in A.
Do items in A, E.
Do item in A.
DoitemsinA,B,D,E.
Do item in A.
Do items in A, E.
Do item in A.
Replace brake fluid (independent of mileage).
DoitemsinA,B,E.
Do item in A.
Do items in A, E.
Do item in A.
DoitemsinA,B,D,E. Replace automatic transmission fluid.
Do item in A.
Do items in A, E.
Do item in A.
DoitemsinA,B,E.
Do item in A. Replace engine oil and oil filter.
Replace air cleaner element.
Lubricate all hinges, locks, and latches.
Check parking brake adjustment.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks.
Inspect exhaust system.
Inspect fuel lines and connections.
Check all lights.
Inspect the underbody.
Replace spark plugs.
Inspect valve clearance. Replace timing belt and inspect water pump.
Inspect drive belt.
Replace dust and pollen filter .
Inspect front and rear brakes.
Rotate tires (follow pattern on page 306).
Inspect tie rod ends, steering gear box, and boots.
Inspect suspension components.
Inspect drive shaft boots.
Service at the indicated distance or time, whichever comes first. Do the items in as required for each distance/time interval.
248
See information on maintenance and emissions warranty, last
column, page .
See timing belt on page for replacement information under
special driving conditions.
See dust and pollen filter on page for replacement
information under special driving conditions.
Check engine oil and coolant at each fuel stop.
Check and adjust valve clearance, cold engine, only if noisy.
NOTE: :
1: 2: 249
302
300
1
2
Maintenance Schedule for Severe Conditions (listed by distance/time)
——y
y
(y
y

Refill the engine with the recom-
mended oil.
Engine oil change capacity
(including f ilter):Let the engine run f or several
minutes, then check the drain bolt
and oil f ilter f or leaks.
Turn of f the engine, let it sit f or
several minutes, then check the oil
level. If necessary, add oil to bring
the level to the upper mark on the
dipstick.
Replace the engine oil f ill cap.
Start the engine. The oil pressure
indicator light should go out within
f ive seconds. If it does not, turn of f
the engine and reinspect your
work.
If the coolant level in the reserve
tank is at or below the MIN line, add
coolant to bring it up to the MAX line.
Inspect the cooling system f or leaks.
The coolant you add should always
be a mixture of 50 percent antif reeze
and 50 percent water. Never add
straight antif reeze or plain water.
9.
8.
7.
6. (4-cylinder models)
(6-cylinder models) A dding Engine Coolant
Engine Oil, Cooling Syst em
Maint enance272
OIL FILTER
6-cylinder models
4-cylinder modelsRESERVE TANK
4.4 US qt (4.2)
4.5 US qt (4.3
) Improper disposal of engine oil can be
harmf ul to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.
——yy
(yy

Always use Honda All Season
Antif reeze/Coolant Type 2. This
coolant is pre-mixed with 50 percent
antif reeze and 50 percent water. It
does not require any additional
mixing. If it is not available, you may
use another major-brand non-silicate
coolant as a temporary replacement.
Make sure it is a high-quality coolant
recommended f or aluminum engines.
However, continued use of any non-
Honda coolant can result incorrosion, causing the cooling
system to malf unction or f ail. Have
the cooling system f lushed and
ref illed with Honda antif reeze/
coolant as soon as possible.
If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
Make sure the engine and radiator
are cool.
Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
Remove the radiator cap by
pushing down and turning
counterclockwise.
1. 2. 3.
CONT INUED
Cooling Syst em
Maint enance273
6-cylinder models RESERVE TANK RADIATOR CAP
4-cylinder modelsRemoving the radiator cap
while the engine is hot can
cause the coolant to spray out,
seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.
——yy
(yy

The cooling system capacity is: Start the engine and let it run forabout 30 seconds. Then turn of f
the engine.
Fill the radiator with coolant up to
the base of the f iller neck.
Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
Install the radiator cap, and
tighten it to the first stop.
Start the engine and let it run until
the radiator cooling f an comes on
at least twice. Then stop the
engine.
Remove the radiator cap. Pour
coolant into the radiator up to the
base of the f iller neck and into the
reserve tank up to the MAX mark.Start the engine and hold it at
1,500 rpm until the cooling f an
comes on. Turn of f the engine.
Check the coolant level in the
radiator and add coolant if needed.
Install the radiator cap, and
tighten it fully.
If necessary, f ill the reserve tank
to the MAX mark. Install the
reserve tank cap.
8. 9.
10. 16.
15.
14.
11. 12. 13.
With 5-speed manual transmission: With automatic transmission:6-cylinder models
Cooling Syst em
Maint enance278
1.35 US gal (5.1)
1.32 US gal (5.0
)
1.77 US gal (6.7
)
——yy
(y
y

The f luid level should be between
theMINandMAXmarksontheside
of the reservoir. If the level is at or
below the MIN mark, your brake
system needs attention. Have the
brake system inspected f or leaks or
worn brake pads.
Always use Honda Heavy Duty
Brake Fluid DOT 3. If it is not
available, you should use only DOT 3
or DOT 4 f luid, f rom a sealed
container, as a temporary
replacement. However, the use of
any non-Honda brake fluid can cause
corrosion and decrease the lif e of the
system. Have the brake system
f lushed and ref illed with Honda
Heavy Duty Brake Fluid DOT 3 as
soon as possible.
Check the f luid level in the reser-
voirs monthly. There are up to two
reservoirs, depending on the model.
They are:
Brake f luid reservoir (all models)
Clutch f luid reservoir
(manual transmission only)
Brake f luid marked DOT 5 is not
compatible with your car’s braking
system and can cause extensive
damage.
The brake f luid should be replaced
according to the time recommenda-
tion in the maintenance schedule. Brake System
Brake and Clutch Fluid
Maint enance284
MAX
MIN
——yy
(yy

The f luid level should be between
theMINandMAXmarksontheside
of the reservoir. If it is not, add
brake f luid to bring it up to that level.
Use the same fluid specified for the
brake system.
Low f luid level can indicate a leak in
the clutch system. Have this system
inspected as soon as possible.Check the level when the engine is
cold. Look at the side of the
reservoir. The f luid should be
between the UPPER LEVEL and
LOWER LEVEL. If it is below the
LOWER LEVEL, add power steering
f luid to the UPPER LEVEL.
CONT INUED
Clutch System Power Steering
Brake and Clutch Fluid, Power Steering
Maint enance285
MAX
MIN UPPER LEVEL
4-cylinder models LOWER LEVEL LOWER LEVELUPPER LEVEL
6-cylinder models
——yy
(yy