2003 FORD MUSTANG brake

PINPOINT TEST I: THE STOPLAMPS ARE ON CONTINUOUSLY z
If the high mounted stoplamp is inoperative, measure the voltage
between the inoperative high mounted stoplamp C475 (C4199 for
Cobra) pin 1, circuit 569 (DG), harness side and ground while
pressing the brake pedal.
z Is the voltage greater than 10 volts? operation.
If rear stoplamp, GO to
H2
.
H2 CHECK CIRCUIT 9 (LG/OG) OR 5 (OG/LB) FOR AN OPEN
z
Disconnect: Multifunction Switch C202b.
z Measure the resistance between the inoperative stoplamp
connector and multifunction switch C202b pin 9, circuit 9
(LG/OG) (LH), or C202b pin 5, circuit 5 (OG/LB) (RH).
z Is the resistance less than 5 ohms? Yes
INSTALL a new
multifunction switch.
REFER to
Section 211 - 05 . TEST the
system for normal
operation.
No
REPAIR the circuit in
question. TEST the
system for normal
operation. Test Step Result / Action to Take
I1 CHECK THE BRAKE PEDAL
POSITION (BPP) SWITCH z
Key in OFF position.
z Disconnect: BPP Switch
C278.
z Do the stoplamps continue
to illuminate? Yes
GO to
I2 .
No
INSTALL a new BPP switch. REFER to Lamp Switch —
Brake Pedal Position (BPP) . TEST the system for normal Klj . 3 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST T: THE REVERSING LAMPS ARE ON
CONTINUOUSLY z
Is the resistance less than 5 ohms? No
REPAIR the circuit.
TEST the system for
normal operation.
Test Step Result / Action to Take
T1 CHECK THE CONTINUITY OF THE
DTR SENSOR (A/T) OR THE
REVERSING LAMP SWITCH (M/T) z
Key in OFF position.
z Disconnect: DTR Sensor C167
(A/T).
z Disconnect: Reversing Lamp Switch
C169 (M/T).
z Set the parking brake.
z Key in ON position.
z Select REVERSE.
z Are the reversing lamps
illuminated? Yes
REPAIR Circuit 140 (BK/PK) for short to battery.
TEST the system for normal operation.
No
INSTALL a new DTR sensor (A/T) or reversing lamp
switch (M/T); REFER to
Section 307 - 01 ,
Section 308 - 03A , or
Section 308 - 03B . TEST the system for
normal operation. Klj . 4 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Lamp Switch —
Brake Pedal Position (BPP)
Removal 1. Disconnect the battery ground cable.
2. Remove the brake pedal position (BPP) switch. 1. Remove the clip.
2. Remove the retainer.
3. Disconnect the electrical connector.
4. Remove the BPP switch.
Installation 1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms
may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven
16 km (10 mi) or more to relearn the strategy.
To install, reverse the removal procedure.
SECTION 417-
01: Exterior Lighting 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

B1408 Driver Power Window Up
Circuit Short to Battery GEM REFER to
Section 501 - 11 .
B1410 Driver Power Window Motor
Circuit Failure GEM REFER to
Section 501 - 11 .
B1426 Lamp Safety Belt Circuit
Short to Battery GEM REFER to
Section 413 - 01 .
B1428 Lamp Safety Belt Circuit
Failure GEM REFER to
Section 413 - 01 .
B1431 Wiper Brake/Run Relay
Circuit Failure GEM REFER to
Section 501 - 16 .
B1432 Wiper Brake/Run Relay
Circuit Short to Battery GEM REFER to
Section 501 - 16 .
B1434 Wiper Hi/Low Speed Relay
Coil Circuit Failure GEM REFER to
Section 501 - 16 .
B1436 Wiper Hi/Low Speed Relay
Coil Circuit Short to Battery GEM REFER to
Section 501 - 16 .
B1438 Wiper Mode Select Switch
Circuit Failure GEM REFER to
Section 501 - 16 .
B1441 Wiper Mode Select Switch
Circuit Short to Ground GEM REFER to
Section 501 - 16 .
B1446 Wiper Park Sense Circuit
Failure GEM REFER to
Section 501 - 16 .
B1448 Wiper Park Sense Circuit
Short to Battery GEM REFER to
Section 501 - 16 .
B1450 Wiper Wash/Delay Switch
Circuit Failure GEM REFER to
Section 501 - 16 .
B1453 Wiper Wash/Delay Switch
Circuit Short to Ground GEM REFER to
Section 501 - 16 .
B1458 Wiper Washer Pump Motor
Relay Circuit Failure GEM REFER to
Section 501 - 16 .
B1460 Wiper Washer Pump Motor
Relay Coil Circuit Short to Battery GEM REFER to
Section 501 - 16 .
B1462 Safety Belt Switch Circuit
Failure GEM REFER to
Section 413 - 09 .
B1466 Wiper Hi/Low Speed Not
Switching GEM REFER to
Section 501 - 16 .
B1473 Wiper Low Speed Circuit
Motor Failure GEM REFER to
Section 501 - 16 .
B1476 Wiper High Speed Circuit
Motor Failure GEM REFER to
Section 501 - 16 .
B1551 Decklid Release Circuit
Failure GEM REFER to
Section 501 - 14B .
B1553 Decklid Release Circuit
Short to Battery GEM REFER to
Section 501 - 14B .
B1555 Ignition Run/Start Circuit
Failure GEM REFER to
Section 211 - 05 .
B1687 Lamp Dome Input Circuit
Short to Battery GEM REFER to
Section 417 - 02 .
B2486 LF Side Repeater Lamp GEM REFER to
Section 417 - 01 . Klj . 4 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Symptom Chart
Pinpoint Tests
CAUTION: Before removing and installing the GEM or its connectors, disconnect the Output Circuit Failure
B2488 RF Side Repeater Lamp
Output Circuit Failure GEM REFER to
Section 417 - 01 .
C1189 Brake Fluid Level Sensor
Input Short Circuit to Ground GEM REFER to
Section 413 - 01 .
C1223 Lamp Brake Warning
Output Circuit Failure GEM REFER to
Section 413 - 01 .
C1225 Lamp Brake Warning
Output Circuit Short to
Battery GEM REFER to
Section 413 - 01 .
Symptom Chart Condition
Possible Sources Action
z No communication with the generic
electronic module z
CJB Fuse 39
(5A)
z GEM.
z Circuitry. z
GO to
Pinpoint Test A .
z The courtesy lamps are inoperative zCJB Fuse 7
(20A).
z Door ajar switch
(es).
z Courtesy lamp
assemblies.
z Circuitry.
z GEM.
z Ignition Switch.
z Headlamp
Switch. z
GO to
Pinpoint Test B .
z The demand lighting is inoperative zCJB Fuse 7
(20A).
z Circuitry.
z GEM.
z Door ajar switch
(es).
z Demand lamp
assemblies.
z Ignition Switch.
z Headlamp
Switch. z
GO to
Pinpoint Test C .
z The illuminated entry is inoperative
when using the remote transmitter z
Remote
transmitter.
z GEM. z
GO to
Pinpoint Test D .
z The battery saver does not
deactivate after timeout z
Circuitry.
z GEM. z
GO to
Pinpoint Test E . Klj . 5 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Daytime Running Lamps (DRL)
Refer to Wiring Diagrams Cell
97 , Daytime Running Lamps for schematic and connector information.
Principles of Operation
Daytime Running Lamps (DRL)
The daytime running lamps (DRL) system operates the low beam headlamps at a reduced intensity.
The DRL module (15A270) supplies pulse width modulated (PWM) voltage, approximately 75%- 92%
of battery voltage, to the low beam headlamps when the following conditions are met:
zThe parking brake control is released.
z The high beam headlamps are disabled.
z The ignition switch (11572) is in the RUN position.
The DRL module remains enabled when the low beam headlamps are turned on.
Inspection and Verification 1. Verify the customer concern by operating the system.
2. Visually inspect for obvious signs of mechanical and electrical damage.
3. Verify the headlamps are operating correctly. Correct any concerns before proceeding to the
SECTION 417-
04: Daytime Running Lamps 2003 Mustang Workshop Manual Special Tool(s)
73III Automotive Meter or
equivalent
105-
R0057
Visual Inspection Chart Mechanical Electrical
z
Damaged DRL module
z Damaged parking brake signal switch and
bracket (15A851) z
Blown battery junction box (BJB) Maxi-
Fuse FOG+DRL (20A)
z Damaged wiring harness
z Loose or corroded connection
z Damaged DRL module
z Damaged parking brake signal switch and
bracket Klj . 1 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

next step. For additional information, refer to
Section 417 - 01 .
4. Verify the parking brake control is fully released.
5. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
6. If the concern is not visually evident, verify the symptom and refer to the Symptom Chart.
Symptom Chart
Pinpoint Tests
PINPOINT TEST A: THE DAYTIME RUNNING LAMPS ARE
INOPERATIVE Symptom Chart Condition
Possible Sources Action
z The daytime running lamps are
inoperative z
BJB Maxi- Fuse
FOG+DRL (20A).
z Circuitry.
z Parking brake
signal switch and
bracket.
z DRL module. z
GO to
Pinpoint Test A .
z The daytime running lamps are
on with the parking brake set z
Circuitry.
z Parking brake
signal switch and
bracket.
z DRL module. z
GO to
Pinpoint Test B .
z The daytime running lamps are
on with the ignition switch off z
Circuitry.
z Ignition switch.
z DRL module. z
GO to
Pinpoint Test C .
z The low beam headlamps are on
at full intensity in DRL mode z
Circuitry.
z Headlamp switch.
z DRL module. z
GO to
Pinpoint Test D .
z The low beam headlamps are on
at reduced intensity with the
headlamp switch on z
Circuitry.
z Headlamp switch. z
REFER to
Section 417 -
01 .
Test Step Result / Action to Take
A1 CHECK THE PARKING BRAKE SWITCH SIGNAL
CIRCUIT TO THE DRL MODULE FOR SHORT TO GROUND NOTE:
Verify the parking brake control is fully released
for this step.
z Key in OFF position.
z Disconnect: DRL Module C1030.
z Measure the resistance between DRL module C1030 Pin
6, Circuit 22 (LB/BK), harness side and ground. Yes
GO to
A3 .
No
GO to A2 . Klj . 2 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Is the resistance greater than 10,000 ohms? A2 CHECK THE PARKING BRAKE SWITCH
z
Disconnect: Parking Brake Switch C306.
z Measure the resistance between DRL module C1030 Pin
6, Circuit 22 (LB/BK), harness side and ground.
z Is the resistance greater than 10,000 ohms? Yes
INSTALL a new parking brake
signal switch and bracket.
TEST the system for normal
operation.
No
REPAIR the circuit. TEST the
system for normal operation.
A3 CHECK VOLTAGE TO THE DRL MODULE
z
Measure the voltage between DRL module C1030 Pin 2,
Circuit 477 (LB/BK), harness side and ground.
z Is the voltage greater than 10 volts? Yes
GO to
A4 .
No
REPAIR the circuit. TEST the
system for normal operation. A4 CHECK IGNITION SENSE INPUT
z
Key in ON position.
z Measure the voltage between DRL module C1030 Pin 3,
Circuit 298 (VT/OG), harness side and ground. Yes
GO to
A5 .
No
REPAIR the circuit. TEST the
system for normal operation. Klj . 3 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...