2003 FORD MUSTANG clutch

INSTALLATION
Transmission
1. NOTE: Before installing the transmission, the ball stud, clutch release lever and the input shaft
must be cleaned and lubricated with grease.
Position the transmission to the clutch adapter housing. Install the eight transmission- to-clutch
adapter housing bolts.
2. Connect the output shaft speed (OSS) sensor electrical connector.
3. Connect the reverse lamp electrical connector.
SECTION 308-
03C: Manual Transaxle/Transmission — T56 2003 Mustang Workshop Manual Material
Item Specification
DEXRON III® (
ATF)
Transmission Fluid
XT -2-QDX or equivalent DEXRON III®
Pipe Sealant with Teflon®
D8AZ-
19554- A or equivalent WSK-
M2G350-
A2 Premium Long Life Grease
XG
-1-C, K or T or equivalent ESA-
M1C75- B Klj . 1 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

4. Connect the wiring harness to the transmission.
5. Connect the clutch release cable to the clutch release fork.
6. Install the clutch release lever cover and bolt.
7. Install the transmission crossmember and the bolts. Klj . 2 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Speed Control
The speed control system consists of the following components:
zspeed control actuator cable (9A825)
z deactivator switch
z output shaft sensor (OSS)
z speed control actuator switches (9C888)
z brake pedal position (BPP) switch (13480)
z speed control servo (9C735)
z clutch pedal position switch (manual transmission only)
SECTION 310-
03: Speed Control 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

z
speed control actuator switches.
z brake pedal position (BPP) switch.
z clutch pedal position (CPP) switch.
z deactivator switch.
The output of the speed control servo is the:
zspeed control actuator cable controlling the throttle position.
Inspection and Verification
NOTE: If any concerns are noted with the speedometer, stoplamps, or horn, address those concerns
by referring to their associated sections before continuing speed control diagnosis.
1. Verify the customer concern by operating the speed control system.
2. Visually inspect for obvious signs of mechanical and electrical damage.
3. If the fault is not visually evident, verify the symptom and GO to the Symptom chart.
Symptom Chart
NOTE: New speed control diagnostic software is available in Version 12 or higher for the diagnostic
tool. When using this software, it is necessary to use Next Generation Speed Control Adapter 007-
00586 with the diagnostic tool.
NOTE: Refer to the Wiring Diagrams for connector numbers stated in the Pinpoint Test.
Visual Inspection Chart Mechanical Electrical
z
Deactivator switch
z Speed control actuator cable not attached to throttle
z Speed control actuator cable not fully seated to the
engine bracket z
Central junction box (CJB)
Fuse:
„15 (15A)
„ 33 (15A)
„ 35 (15A)
z Battery junction box (BJB)
fuse:
„HORN (20A)
z Wiring harness
z Loose or corroded
connections
z Speed control actuator
switches
Symptom Chart Condition
Possible Sources Action
z The speed control is zCentral junction zGo To Pinpoint Test A . Klj . 2 ba
132003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

inoperative
box (CJB) fuse
17 (15A), 33
(15A).
z Battery junction
box (BJB) fuse
HORN (20A).
z Circuitry.
z Deactivator
switch.
z Clutch pedal
position (CPP)
switch.
z Speed control
actuator switch.
z Speed control
servo.
z Powertrain
control module
(PCM).
z The set speed
fluctuates z
Circuitry.
z Speed control
servo.
z Powertrain
control module
(PCM). z
Go To Pinpoint Test B .
z Engine. zREFER to the Powertrain
Control/Emissions
Diagnosis (PC/ED)
manual.
z The speed control
does not disengage
when the brakes are
applied z
Central junction
box (CJB) fuse
33 (15A).
z Circuitry.
z Brake pedal
position (BPP)
switch.
z Speed control
servo. z
Go To Pinpoint Test C .
z The speed control
does not disengage
when the clutch is
applied z
Cluch pedal
position (CPP)
switch.
z Speed control
servo. z
Go To Pinpoint Test D .
z The speed control
switch is
inoperative— COAST z
Speed control
actuator switch.
z Speed control
servo. z
Go To Pinpoint Test E .
z The speed control
switch is
inoperative—
SET/ACCEL z
Speed control
actuator switch.
z Speed control
servo. z
Go To Pinpoint Test F .
z The speed control
switch is
inoperative—
RESUME z
Speed control
actuator switch.
z Speed control
servo. z
Go To Pinpoint Test G .
z The speed control
switch is
inoperative— OFF z
Speed control
actuator switch.
z Speed control
servo. z
Go To Pinpoint Test H . Klj . 3 ba
132003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

PINPOINT TEST C: THE SPEED CONTROL DOES NOT DISENGAGE
WHEN THE BRAKES ARE APPLIED
PINPOINT TEST D: THE SPEED CONTROL DOES NOT DISENGAGE
WHEN THE CLUTCH IS APPLIED B2 CHECK THE SPEED CONTROL
ACTUATOR CABLE z
NOTE: The speed control actuator cable
must be disconnected at both ends while
carrying out this test.
z Check the speed control actuator cable
for sticking or binding at the speed
control servo and throttle body.
z Is the speed control actuator cable
OK? Yes
GO to
B3 .
No
INSTALL a new speed control actuator cable;
REFER to Actuator Cable — Speed Control .
TEST the system for normal operation. B3 CHECK THE SPEED CONTROL SERVO
z
INSTALL a known good speed control
servo.
z Test drive the vehicle for correct
operation.
z Does the speed control operate
correctly? Yes
INSTALL a new speed control servo; REFER
to
Actuator — Speed Control Servo . TEST the
system for normal operation.
No
INSTALL a new PCM; REFER to Section 303 -
14 . TEST the system for normal operation.
Test Step Result / Action to Take
C1 CHECK THE BPP SWITCH CIRCUITRY
z
Key in OFF position.
z Disconnect: Speed Control Servo C122 .
z Measure the voltage between speed control servo C122 Pin 4,
Circuit 511 (LG), harness side and speed control servo C122
Pin 10, Circuit 1205 (BK), harness side, while depressing the
brake pedal.
z Is the voltage greater than 10 volts? Yes
INSTALL a new speed
control servo; REFER to
Actuator
— Speed
Control Servo . TEST
the system for normal
operation.
No
REPAIR Circuit 810
(RD/LG) and Circuit 511
(LG) as necessary.
TEST the system for
normal operation. Test Step Result / Action to Take
D1 CHECK THE CLUTCH PEDAL POSITION (CPP) SWITCH
z
Key in OFF position.
z Disconnect: CPP Switch C2072.
z Measure the resistance between CPP switch pin 2
(component side) and CPP switch pin 1 (component side), Yes
INSTALL a new speed
control servo; REFER to
Actuator
— Speed Control Klj . 10 ba
132003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

PINPOINT TEST E: THE SPEED CONTROL SWITCH IS
INOPERATIVE—
COAST
PINPOINT TEST F: THE SPEED CONTROL SWITCH IS
INOPERATIVE— SET/ACCEL while depressing and releasing clutch pedal.
z Is the resistance greater than 10,000 ohms with the
clutch pedal depressed and less than 5 ohms with the
clutch pedal released? Servo . TEST the system
for normal operation.
No
INSTALL a new CPP
switch. TEST the system
for normal operation. Test Step Result / Action to
Take E1 CHECK THE SPEED CONTROL ACTUATOR SWITCH
z
Key in OFF position.
z Disconnect: Speed Control Servo C122.
z Measure the resistance between speed control servo C122 Pin
5, Circuit 151 (LB/BK), harness side and speed control servo
C122 Pin 6, Circuit 848 (DG/OG), harness side, while pressing
the speed control actuator switch COAST.
z Is the resistance between 108 and 132 ohms? Yes
INSTALL a new speed
control servo; REFER
to
Actuator — Speed
Control Servo . TEST
the system for normal
operation.
No
INSTALL a new speed
control actuator switch;
REFER to Switch —
Speed Control
Actuator . TEST the
system for normal
operation. Test Step Result / Action to
Take F1 CHECK THE SPEED CONTROL ACTUATOR SWITCH
z
Key in OFF position.
z Disconnect: Speed Control Servo C122.
z Measure the resistance between speed control servo C122 Pin 5,
Circuit 151 (LB/BK), harness side and speed control servo C122
Pin 6, Circuit 848 (DG/OG), harness side, while pressing the
speed control actuator switch SET/ACCEL. Yes
INSTALL a new speed
control servo; REFER
to
Actuator — Speed
Control Servo . TEST
the system for normal
operation. Klj . 11 ba
132003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

SPECIFICATIONS
a
Manifold gauge set pressures may vary slightly depending on the distance between the service
SECTION 412-
00: Climate Control System - General Information 2003 Mustang Workshop Manual General Specifications
Item Specification
A/C Compressor
Type FS-
10 swashplate, 5 double- acting pistons Displacement 170 cc (10.4 cu in)
Rotation Clockwise
A/C Pressure Relief Valve
a Open pressures 3,792-
4,137 kPa (550- 600 psi) A/C Pressure Sensor Refer to the Powertrain Control/Emissions
Diagnosis (PC/ED) manual.
Coolant Hose Lubricant
MERPOL® ESE-
M99B144- B Evaporator Core Orifice
Color Orange
Diameter 1.45 mm (0.057 in)
Magnetic Clutch
Air gap clearance 0.35-
0.75 mm (0.014- 0.030 in) Dual Function Pressure Switch (V8)
a Fan on/open 2,137-
2,344 kPa (310- 340 psi) Fan off/close 1,655-
2,137 kPa (240- 310 psi) Clutch off/open 2,999-
3,275 kPa (435- 475 psi) Clutch on/closed 1,517-
1,931 kPa (220- 280 psi) Pressure Cutoff Switch (V6)
a Open 2,999-
3,275 kPa (435- 475 psi) Close 1,586-
1,999 kPa (230- 290 psi) A/C Cycling Switch Open and Closed Pressures
a Open pressure 145-
159 kPa (21- 23 psi) Close pressure 290 kPa (42 psi)
Refrigerant Lubricant and Capacity
PAG Refrigerant Compressor Oil (R-134a Systems)
F7AZ- 19589- DA (Motorcraft YN-12- C) WSH-
M1C231- B Capacity 254 ml (8.6 oz)
Refrigerant and Capacity
R134a Refrigerant YN-
19 WSH-
M17B19- A Capacity .96 kg (34 oz)
Refrigerant System Cleaner
A/C Systems Flushing Solvent F4AZ-19579-
A — Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...