2003 FORD MUSTANG height

REMOVAL AND INSTALLATION
Upper Arm —
Cobra
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Mark the rear shock absorber (18125) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
3. Remove both wheel and tire assemblies. For additional information, refer to Section 204 - 04 .
4. Remove the rear brake disc. For additional information, refer to Section 206 - 04 .
5. Remove the rear springs (5560). For additional information, refer to Spring — Cobra in this
section.
6. Raise the subframe into position and remove the front bolts.
7. Lower the subframe from the vehicle.
8. Mark the cam bolt position relative to the upper suspension arm and bushing (5500).
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9.
NOTE: Mark a new cam bolt in the same position as the old one for assembly reference before
discarding the old bolt.
Disconnect the upper suspension arm and bushing from the knuckle (5A968/5A969). 1. Remove and discard the nut and bolt.
2. Disconnect the upper suspension arm and bushing.
10. Remove the upper suspension arm and bushing. 1. Remove and discard the nuts and bolts.
2. Remove the upper suspension arm and bushing.
Installation CAUTION: The upper suspension arm and bushing nuts must be tightened with the
suspension at curb height. Failure to do so can result in bushing failure, resulting in poor ride
and handling.
NOTE: If installing a new upper suspension arm and bushing, mark the cam bolt side of the new arm
in the same position as the old arm for assembly reference.
1. Install the upper suspension arm and bushing. 1. Position the arm and bushing on the subframe. Klj . 2 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2. Install new bolts and nuts. Do not tighten the nuts at this time.
2. Connect the upper suspension arm and bushing to the knuckle. 1. Position the arm and bushing.
2. Install a new cam bolt and a new nut. Do not tighten the nut at this time.
3. Raise the subframe into position and install new front bolts.
4. Install the springs. For additional information, refer to Spring — Cobra in this section.
5. Position a jack stand under the lower suspension arm and bushing.
6. Raise the suspension until the shock absorber is compressed to the alignment mark (curb height). Klj . 3 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Lower Arm
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Mark the rear shock absorber (18125) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Remove the muffler assembly(ies). For additional information, refer to Section 309 - 00 .
3. Remove the rear spring (5560). For additional information, refer to Spring — Coil in this section.
4. Remove the lower suspension arm and bushing (5A649) from the body attachment. 1. Remove and discard the bolt and nut.
2. Remove the lower arm.
Installation 1. Install the lower suspension arm and bushing to the body attachment. 1. Position the lower arm. 2. Install a new bolt and a new nut. Do not tighten at this time. SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2.
NOTE: Tighten the lower suspension arm and bushing- to-body attachment bolt after installing
the spring while the suspension is at curb height.
Install the rear spring. For additional information, refer to Spring — Coil in this section.
3. Install the muffler assembly(ies). For additional information, refer to Section 309 - 00 . Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Wheel Knuckle —
Cobra
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Mark the rear shock absorber (18125) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
3. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
4. Remove and discard the rear hub retainer (4B477).
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
Front Hub Remover
205-
D070 (D93P-1175- B) or
Equivalent Steering Arm Remover
211-
003 (T64P-9171- A) Klj . 1 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

5. Connect the toe link to the knuckle.
1. Position the toe link in the knuckle.
2. Install a new nut.
3. Install a new cotter pin.
6. CAUTION: Make sure the hardened washer is installed between the lower
suspension arm and bushing and the shock absorber. Failure to do so can result in
damage and failure of the lower suspension arm and bushing.
Connect the shock absorber to the lower suspension arm and bushing and install the bolt and a
new nut.
7. Raise the suspension until the shock absorber is compressed to the previously established alignment mark (curb height). Klj . 6 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Spring —
Coil
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
All vehicles
1. Mark the rear shock absorber (18125) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Raise the vehicle. For additional information, refer to Section 100 - 02 .
3. Disconnect the anti- lock sensor wire.
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
Hi-
Lift Jack
014- 00942 or Equivalent Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...