2003 FORD MUSTANG fuel pump

GENERAL PROCEDURES
Fill
1. WARNING: Do not mix oil types, any mixture or any unapproved oil can lead to seal
deterioration and leaks. A leak can ultimately cause loss of fluid, which can result in a
loss of power steering assist.
Check the fluid level. If necessary, fill the reservoir to the correct level.
zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
2. Remove the fuel pump fuse from the battery junction box.
3. Raise the front wheels off the floor. For additional information, refer to Section 100 - 02 .
4. CAUTION: Do not crank the engine for more than 15 seconds at a time. Allow the
starter to cool for 1 minute before cranking again. Premature starter failure can occur.
CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump will occur.
Turn the steering wheel from stop- to-stop while cranking the engine.
5. Lower the vehicle.
6. CAUTION: Do not overfill the reservoir.
Check the fluid level. If necessary, fill the reservoir to the correct level. zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
7. Install the fuel pump fuse.
SECTION 211-
00: Steering System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

(PC/ED) manual.
z Damaged valve
tappet or lash
adjuster. z
INSTALL a new valve tappet or
lash adjuster.
z Damaged valve
tappet guide or
valve tappet. z
INSTALL a new valve tappet
guide or valve tappet.
z Burnt or sticking
valve. z
REPAIR or INSTALL a new
valve.
z Weak or broken
valve spring. z
INSTALL a new valve spring.
z Carbon
accumulation in
combustion
chamber. z
ELIMINATE carbon buildup.
z Excessive oil
consumption z
Leaking oil. zREPAIR oil leakage.
z Malfunctioning PCV
system. z
REPAIR or INSTALL new
necessary components.
z Worn valve stem
seal. z
INSTALL a new valve stem seal.
z Worn valve stem or
valve guide. z
INSTALL a new valve and valve
guide.
z Sticking piston
rings. z
REPAIR or INSTALL new piston
rings.
z Worn piston ring
groove. z
INSTALL a new piston and
piston pin.
z Worn piston or
cylinder. z
REPAIR or INSTALL a new
piston or cylinder block.
z Engine noise zLeaking exhaust
system. z
REPAIR exhaust leakage.
z Incorrect drive belt
tension. z
REFER to Section 303 - 05 .
z Malfunctioning
generator bearing. z
Refer to the appropriate section
in Group 414 for the procedure.
z Malfunctioning
water pump
bearing. z
REFER to Section 303 - 03A .
z Malfunctioning or
damaged cooling
system. z
REFER to Section 303 - 03A .
z Malfunctioning or
damaged fuel
system. z
Refer to the appropriate section
in Group 303 for the procedure.
REFER to the Powertrain
Control/Emissions Diagnosis
(PC/ED) manual.
z Loose timing
chain/belt (6268). z
ADJUST or INSTALL a new
timing chain/belt.
z Damaged timing
chain tensioner
(6L266). z
INSTALL a new timing chain
tensioner.
z Excessive main
bearing clearance. z
ADJUST clearance or INSTALL
a new crankshaft main bearing
(6333). Klj . 4 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Engines need oil to lubricate the following internal components:
zcylinder block cylinder walls
z pistons and piston, pin and rings (6102)
z intake and exhaust valve stems
z intake and exhaust valve guides
z all internal engine components
When the pistons move downward, a thin film of oil is left on the cylinder walls. As the vehicle is
operated, some oil is also drawn into the combustion chambers past the intake and exhaust valve
stem seals and burned.
The following is a partial list of conditions that can affect oil consumption rates:
zengine duty cycle
z operator driving habits
z ambient temperature
z quality and viscosity of the oil
Operation under varying conditions can frequently be misleading. A vehicle that has been run for
several thousand miles on short trips or in below- freezing ambient temperatures may have consumed
a "normal" amount of oil. However, when checking the engine oil level, it may measure up to the FULL
or MAX on the oil level dipstick due to dilution (condensation and fuel) in the engine crankcase. The
vehicle might then be driven at high speeds on the highway where the condensation and fuel boil off.
The next time the engine oil is checked, it may appear that a liter (quart) of oil was used in about 160
km (100 miles). This perceived 160 km (100 miles) per liter (quart) oil consumption rate causes
customer concern even though the actual overall oil consumption rate is about 2,400 km (1,500 miles)
per liter (quart).
Make sure the selected engine oil meets the current recommended API performance category with
SAE viscosity grade as shown in the vehicle Owner's Guide. It is also important that the engine oil is
changed at the intervals specified. Refer to the vehicle Owner's Guide.
Oil Pressure Test
1. Disconnect and remove the oil pressure sensor (9278) from the engine.
2. Connect the Oil Pressure Gauge to the oil pressure sender oil galley port.
3. Run the engine until normal operating temperature is reached.
4. Run the engine at the specified rpm and record the gauge reading.
5. The oil pressure should be within specifications; refer to the specification chart in the appropriate engine section.
6. If the pressure is not within specification, check the following possible sources: zinsufficient oil
z oil leakage
z worn or damaged oil pump
z oil pump screen cover and tube (6622)
z excessive main bearing clearance Klj . 13 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. Inspect for normal burning.
zCheck for light tan or gray deposits on the firing tip.
5. Inspect for pre- ignition, identified by melted electrodes and a possibly damaged insulator.
Metallic deposits on the insulator indicate engine damage. This may be caused by incorrect
ignition timing, wrong type of fuel or the unauthorized installation of a heli- coil insert in place of
the spark plug threads.
zInstall a new spark plug.
6. Inspect for overheating, identified by a white or light gray spots and with bluish- burnt
appearance of electrodes. This is caused by engine overheating, wrong type of fuel, loose spark
plugs, spark plugs with an incorrect heat range, low fuel pump pressure or incorrect ignition
timing.
zInstall a new spark plug. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

a
20- 200 seconds to leakdown 3.18 mm (0.125 in) with 225 Newtons (50 pounds) load and tappet filled
with leak- down fluid. —
desired Connecting rod bearing-
to-crankshaft clearance
— allowable 0.022-
0.069 mm (0.00086- 0.0027 in) Connecting rod side clearance 0.11-
0.49 mm (0.0047- 0.0193 in) Balance Shaft
Journal diameter 52.108-
52.082 mm (2.0515- 2.0505 in) Bore inside diameter 55.689-
55.664 mm (2.192- 2.191 in) Maximum runout 0.025 mm (0.001 in)
End play 0.075-
0.200 mm (0.003- 0.008 in)
Torque Specifications Description Nm lb-
ft lb-
in EGR transducer bracket-
to-intake manifold bolts 10 — 89
Ignition coil-
to-intake manifold bolts 6 — 53
Water outlet tube-
to-intake manifold stud bolt 10 — 89
EGR tube-
to-EGR valve nut 40 30 —
Water outlet tube-
to-front water pump bolt 10 — 89
Fuel supply manifold bolts 10 — 89
LH valve cover-
to-cylinder head bolts 10 — 89
LH valve cover-
to-cylinder head stud bolts 10 — 89
EGR tube-
to-exhaust manifold nut 40 30 —
RH valve cover-
to-cylinder head bolts 10 — 89
RH valve cover-
to-cylinder head stud bolts 10 — 89
Coolant recovery reservoir-
to-cylinder head stud bolts 10 — 89
Coolant recovery reservoir-
to-bracket bolts 5 — 44
Crankshaft pulley bolt 160 118 —
Camshaft position sensor bolts 3 — 27
Camshaft synchronizer-
to-front cover bolt 25 18 —
Front cover-
to-cylinder block bolts 25 18 —
Radiator fan shroud-
to-radiator bolts 9 — 80
Camshaft thrust plate-
to-cylinder block bolts 12 9 —
Camshaft synchronizer drive gear-
to-camshaft bolt 45 33 —
Timing chain tensioner-
to-cylinder block bolts 12 9 —
Exhaust manifold-
to-cylinder head nuts 33 24 —
Power steering pump bracket-
to-water pump nuts 20 15 —
Power steering pump bracket-
to-generator bracket bolts 20 15 —
Generator bracket-
to-cylinder head bolts 40 30 —
Exhaust manifold studs 8 — 71
A/C compressor bracket-
to-cylinder head bolts 48 35 —
A/C compressor bracket-
to-cylinder head nut 48 35 — Klj . 4 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
are positioned so that their tips direct fuel just ahead of the engine intake valves.
z are connected in series with the fuel pressure sensor.
z supply fuel from the fuel tank with a fuel pump mounted in the fuel tank.
A constant fuel pressure drop is maintained across the fuel injectors by the fuel pressure sensor. The
fuel pressure sensor:
zis positioned upstream from the fuel injectors on the fuel injection supply manifold.
Valve Train
The valve train operates as follows:
zball- tip hydraulic lash adjusters provide automatic lash adjustment.
z roller followers ride on the camshaft lobes, transferring the up-and- down motion of the
camshafts to the valves in the cylinder heads.
Positive Crankcase Ventilation System
All engines are equipped with a closed- type positive crankcase ventilation system recycling the
crankcase vapors to the upper intake manifold.
Lubrication System
The engine lubrication system operates as follows:
zoil is drawn into the oil pump through the oil pump screen cover and tube in the sump of the oil
pan.
z oil is pumped through the oil bypass filter on the left front side of the cylinder block.
z oil enters the main oil gallery where it is distributed to the crankshaft main journals and to both
cylinder heads.
z From the main journals, the oil is routed through cross- drilled passages in the crankshaft to
lubricate the connecting rod bearings. Controlled leakage through the crankshaft main bearings
and connecting rod bearings is slung radially outward to cool and lubricate the cylinder walls as
well as the entire connecting rod, piston and piston rings assembly.
z The left cylinder head is fed from a drilling into the supply passage feeding the main gallery at
the front of the cylinder block. The right cylinder head is fed from a drilling into the rear of the
main gallery. Main gallery pressure is reduced as it enters the cylinder head galleries through
fixed serviceable orifices located at the upper part of the feed passages. It is this reduced
pressure in the cylinder head galleries which feeds the camshaft journals, the hydraulic lash
adjusters and the primary and secondary timing chain tensioners.
z The camshaft lobe and roller followers are lubricated by splash created through valve train
operation.
Oil Pump
The lubrication system of the 4.6L (4V) engine is designed to provide optimum oil flow to critical
components of the engine through its entire operating range. The heart of the system is a positive
displacement internal gear oil pump using top seal rotors. Generically this design is known as a gerotor
pump, which operates as follows.
zThe oil pump is mounted on the front face of the cylinder block. Klj . 2 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
are connected in series with the fuel pressure sensor.
z supply fuel from the fuel tank with a fuel pump mounted in the fuel tank.
A constant fuel pressure drop is maintained across the fuel injectors by the fuel pressure sensor. The
fuel pressure sensor:
zis positioned upstream from the fuel injectors on the fuel injection supply manifold.
Valve Train
The valve train operates as follows:
zball- tip hydraulic lash adjusters provide automatic lash adjustment.
z roller followers ride on the camshaft lobes, transferring the up-and- down motion of the
camshafts to the valves in the cylinder heads.
Positive Crankcase Ventilation System
All engines are equipped with a closed- type positive crankcase ventilation system recycling the
crankcase vapors to the upper intake manifold.
Lubrication System
The engine lubrication system operates as follows:
zoil is drawn into the oil pump through the oil pump screen cover and tube in the sump of the oil
pan.
z oil is pumped through the oil bypass filter on the left front side of the cylinder block.
z oil enters the main oil gallery where it is distributed to the crankshaft main journals and to both
cylinder heads.
z From the main journals, the oil is routed through cross- drilled passages in the crankshaft to
lubricate the connecting rod bearings. Controlled leakage through the crankshaft main bearings
and connecting rod bearings is slung radially outward to cool and lubricate the cylinder walls as
well as the entire connecting rod, piston and piston rings assembly.
z The left cylinder head is fed from a drilling into the supply passage feeding the main gallery at
the front of the cylinder block. The right cylinder head is fed from a drilling into the rear of the
main gallery. Main gallery pressure is reduced as it enters the cylinder head galleries through
fixed serviceable orifices located at the upper part of the feed passages. It is this reduced
pressure in the cylinder head galleries which feeds the camshaft journals, the hydraulic lash
adjusters and the primary and secondary timing chain tensioners.
z The camshaft lobe and roller followers are lubricated by splash created through valve train
operation.
Oil Pump
The lubrication system of the 4.6L (4V) engine is designed to provide optimum oil flow to critical
components of the engine through its entire operating range. The heart of the system is a positive
displacement internal gear oil pump using top seal rotors. Generically this design is known as a gerotor
pump, which operates as follows.
zThe oil pump is mounted on the front face of the cylinder block.
z The inner rotor is piloted on the crankshaft post and is driven through flats on the crankshaft. Klj . 2 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. Inspect for gap bridged.
zThis can be identified by deposit build up closing the gap between electrodes.
z This may be caused by oil or carbon fouling.
z Clean the spark plug.
5. Inspect for oil fouling. zThis can be identified by wet black deposits on the insulator shell bore electrodes.
z This may be caused by excessive oil entering the combustion chamber through worn
rings and pistons, excessive clearance between valve guides and stems, or worn or
loose bearings. Correct the oil problem.
z Install a new spark plug.
6. Inspect for carbon fouling. zThis can be identified by black, dry, fluffy carbon deposits on the insulator tips, exposed
shell surfaces and electrodes.
z This may be caused by too cold a plug, dirty air cleaner, damaged fuel pump, too rich a
fuel mixture or excessive idling.
z Clean the spark plug. Klj . 2 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...