2003 FORD MUSTANG ESP

10. Using the special tools, remove the inner rear axle pinion bearing cup (4628).
Installation
Using special tool 205- 024
NOTE: This is the preferred method for installing the pinion bearing cups. If necessary, proceed to
Using special tools 205- 153, 205-024, 205-231, and 205- D055 in this procedure for an alternate
method.
1. Position the special tools and the inner and outer pinion bearing cups in their respective bores. 1. After placing the inner and outer bearing cups in their bores, place the special tool on the
inner bearing cup.
2. Place the special tool on the outer bearing cup.
3. Install the special tool.
2. Tighten the special tool to seat the pinion bearing cups in their bores.
3. CAUTION: Always install new differential pinion bearings when installing new
pinion bearing cups. NOTE: If the feeler gauge can fit between a cup and the bottom of its bore at any point around Klj . 5 ba
132003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9.
CAUTION: Do not use acids or solvents when cleaning the differential clutch pack.
Wipe components only with a clean, lint- free cloth.
Clean and inspect the differential clutch packs for wear and damage and install new parts as
necessary.
Assembly
1. CAUTION: 118 ml (4 oz) of the specified Ford Friction Modifier must be used in the
axle.
Lubricate each steel clutch plate and soak all friction plates for no less than 15 minutes.
zUse Additive Friction Modifier C8AZ- 19B546-A or equivalent meeting Ford specification
EST- M2C118- A
2. CAUTION: Do not mix the differential clutch packs or shims from one side with the
other.
Assemble the differential clutch packs (without the shims) on their respective differential side
gears. Klj . 4 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

new pinion bearings in the Specifications portion of this section.
z For used pinion bearings, if the preload recorded prior to disassembly is lower than the
specification for used bearings, then tighten the nut to specification. Refer to torque
specifications for used pinion bearings in the Specifications portion of this section.
z For used pinion bearings, if the preload recorded prior to disassembly is higher than the
specification for used bearings, then tighten the nut to the original reading as recorded.
18. CAUTION: 118 ml (4 oz) of Additive Friction Modifier C8AZ- 19B546-A or equivalent
meeting Ford specification EST- M2C118-A must be used in the axle.
Lubricate each steel clutch plate and soak all friction plates for no less than 15 minutes. zUse Additive Friction Modifier C8AZ- 19B546-A or equivalent meeting Ford specification
EST- M2C118- A.
19. CAUTION: Do not mix the clutch plates, clutch discs or shim from one side with the
other.
Assemble the differential clutch packs (without the shims) on their respective differential side gear. Klj . 20 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

3. If the concern remains after the inspection, connect the scan tool to the data link connector
(DLC) located beneath the instrument panel and select the vehicle to be tested from the scan
tool menu. If the scan tool does not communicate with the vehicle: 1. Check that the program card is correctly installed.
2. Check the connections to the vehicle.
3. Check the ignition switch position.
4. If the scan tool still does not communicate with the vehicle, refer to the scan tool Manual.
5. Carry out the DATA LINK DIAGNOSTIC TEST. If the scan tool responds with: 1. CKT914, CKT915 or CKT70 = ALL ECUS NO RESP/NOT EQUIP, refer to Section 418-00.
2. NO RESP/NOT EQUIP for the anti- lock brake control module, Go To Pinpoint Test A .
3. SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and carry out self- test diagnostics for the anti-lock brake
control module.
6. If the DTCs retrieved are related to the concern, go to the Anti- Lock Brake Control Module
Diagnostic Trouble Code (DTC) Reference Chart to continue diagnostics.
7. If no DTCs related to the concern are retrieved, GO to Symptom Chart to continue diagnostics.
Anti-Lock Brake Control Module Diagnostic Trouble Code (DTC) Index
NOTE: If a wheel speed signal fault or a pump motor fault is detected, the yellow ABS warning
indicator cannot be reset with the key OFF and key ON method. The vehicle must be driven over 12
km/h (8 mph) for the anti- lock brake control module to carry out a re- check of the system before the
yellow ABS warning indicator is turned OFF. Visual Inspection Chart Mechanical Electrical
z
Low brake fluid
z Anti- lock brake sensor
z Anti- lock brake sensor indicator
z Base brake system z
Central junction box (CJB)Fuse:
„15 (10A)
„ 29 (15A)
„ 33 (15A)
„ 35 (15A)
z Battery junction box (BJB) Fuse:
„ABS 1 (50A)
„ ABS 2 (20A)
z Circuitry
z Damaged or corroded connectors
z Yellow ABS warning indicator
z Loose grounds
Anti-Lock Brake Control Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action
B1318 Battery Voltage Low ABS Go To Pinpoint Test C .
B1342 ECU Is Defective ABS INSTALL a new anti-
lock brake control module;
REFER to Module . REPEAT the self-
test. B1484 Brake Pedal Input Open Circuit ABS Go To Pinpoint Test D . Klj . 2 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Inspection and Verification
1. Verify the customer concern by operating the system.
2. Visually inspect for obvious signs of mechanical and electrical damage.
3. If the concern remains after the inspection, connect the scan tool to the data link connector (DLC) located beneath the instrument panel and select the vehicle to be tested from the scan
tool menu. If the scan tool does not communicate with the vehicle: 1. Check that the program card is correctly installed.
2. Check the connections to the vehicle.
3. Check the ignition switch position.
4. If the scan tool still does not communicate with the vehicle, refer to the scan tool manual.
5. Carry out the DATA LINK DIAGNOSTIC TEST. If the scan tool responds with: 1. CKT914, CKT915 or CKT70 = ALL ECUS NO RESP/NOT EQUIP, refer to Section 418-00.
2. NO RESP/NOT EQUIP for the anti- lock brake control module, Go To Pinpoint Test A .
3. SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs),
erase the continuous DTCs and carry out self- test diagnostics for the anti-lock brake
control module.
6. If the DTCs retrieved are related to the concern, go to the Anti- Lock Brake Control Module
Diagnostic Trouble Code (DTC) Index to continue diagnostics.
7. If no DTCs related to the concern are retrieved, GO to Symptom Chart to continue diagnostics.
Anti-Lock Brake Control Module Diagnostic Trouble Code (DTC) Index
NOTE: If a wheel speed signal fault or a pump motor fault is detected, the yellow ABS warning
indicator cannot be reset with the key OFF and key ON method. The vehicle must be driven over 12
km/h (8 mph) for the anti- lock brake control module to do a re- check of the system before the yellow
ABS warning indicator is turned OFF. Visual Inspection Chart Mechanical Electrical
z
Low brake fluid
z Anti- lock brake sensor
z Anti- lock brake sensor indicator
z Base brake system
z Wheel bearings z
Central junction box (CJB) Fuse:
„5 (15A)
„ 15 (10A)
„ 29 (15A)
„ 33 (15A)
„ 35 (15A)
z Battery junction box (BJB) Fuse:
„ABS 1 (50A)
„ ABS 2 (20A)
z Circuitry
z Damaged or corroded connectors
z ABS warning indicator
z Loose grounds Klj . 2 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
check the connections to the vehicle.
z check the ignition switch position.
4. If the scan tool still does not communicate with the vehicle, refer to the scan tool manual.
5. Carry out the DATA LINK DIAGNOSTIC TEST. If the scan tool responds with: zCKT914, CKT915 or CKT70 =ALL ECUS NO RESP/NOT EQUIP, refer to Section 418 -
00 .
z NO RESP/NOT EQUIP for GEM, go to Pinpoint Test A.
z SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs),
erase the continuous DTCs and carry out self- test diagnostics for the GEM.
6. If the DTCs retrieved are related to the concern, go to the GEM Diagnostic Trouble Code (DTC) Index to continue diagnostics.
7. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart to continue diagnostics.
GEM Diagnostic Trouble Code (DTC) Index GEM Diagnostic Trouble Code (DTC) Index DTC Description Source Action
B1217 Horn Relay Coil Circuit Failure GEM REFER to
Section 413 - 06 .
B1218 Horn Relay Coil Circuit Short to
Vbatt GEM REFER to
Section 413 - 06 .
B1312 Lamp Headlamp Input Circuit
Short to Battery GEM REFER to
Section 417 - 01 .
B1317 Battery Voltage High GEM REFER to
Section 414 - 00 .
B1318 Battery Voltage Low GEM REFER to
Section 414 - 00 .
B1322 Driver Door Ajar Circuit Short to
Ground GEM REFER to
Section 417 - 02 .
B1330 Passenger Door Ajar Circuit
Short to Ground GEM REFER to
Section 417 - 02 .
B1334 Decklid Ajar Rear Door Circuit
Short to Ground GEM REFER to
Section 417 - 02 .
B1339 Chime Input Request Circuit
Short to Battery GEM REFER to
Section 413 - 09 .
B1340 Chime Input Request Circuit
Short to Ground GEM REFER to
Section 413 - 09 .
B1342 ECU Is Defective GEM CLEAR the DTC. Retrieve the DTCs. If DTC
B1342 is retrieved, INSTALL a new GEM. REFER to Section 419 - 10 .
B1353 Ignition Key-
In Circuit Open GEM REFER to
Section 413 - 09 .
B1359 Ignition Run/Acc Circuit Failure GEM GO to
Pinpoint Test E .
B1396 Power Door Lock Circuit Short
to Battery GEM REFER to
Section 501 - 14B .
B1397 Power Door Unlock Circuit
Short to Battery GEM REFER to
Section 501 - 14B . Klj . 2 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

required to obtain the highest reading.
5. Repeat the test on each cylinder, cranking the engine approximately the same number of compression strokes.
Compression Test— Test Results
The indicated compression pressures are considered within specification if the lowest reading cylinder
is at least 75 percent of the highest reading. Refer to the Compression Pressure Limit Chart.
If one or more cylinders reads low, squirt approximately one tablespoon of engine oil on top of the
pistons in the low- reading cylinders. Repeat the compression pressure check on these cylinders. Compression Test — Interpreting Compression Readings Compression Pressure Limit Chart
Maximum
Pressure Minimum
Pressure Maximum
Pressure Minimum
Pressure Maximum
Pressure Minimum
Pressure Maximum
Pressure Minimum
Pressure 924 kPa
(134 psi) 696 kPa
(101 psi) 1131 kPa
(164 psi) 848 kPa
(123 psi) 1338 kPa
(194 psi) 1000 kPa
(146 psi) 1544 kPa
(224 psi) 1158 kPa
(168 psi) 938 kPa
(136 psi) 703 kPa
(102 psi) 1145 kPa
(166 psi) 855 kPa
(124 psi) 1351 kPa
(196 psi) 1014 kPa
(147 psi) 1558 kPa
(226 psi) 1165 kPa
(169 psi) 952 kPa
(138 psi) 717 kPa
(104 psi) 1158 kPa
(168 psi) 869 kPa
(126 psi) 1365 kPa
(198 psi) 1020 kPa
(148 psi) 1572 kPa
(228 psi) 1179 kPa
(171 psi) 965 kPa
(140 psi) 724 kPa
(106 psi) 1172 kPa
(170 psi) 876 kPa
(127 psi) 1379 kPa
(200 psi) 1034 kPa
(150 psi) 1586 kPa
(230 psi) 1186 kPa
(172 psi) 979 kPa
(142 psi) 738 kPa
(107 psi) 1186 kPa
(172 psi) 889 kPa
(129 psi) 1303 kPa
(202 psi) 1041 kPa
(151 psi) 1600 kPa
(232 psi) 1200 kPa
(174 psi) 933 kPa
(144 psi) 745 kPa
(109 psi) 1200 kPa
(174 psi) 903 kPa
(131 psi) 1407 kPa
(204 psi) 1055 kPa
(153 psi) 1055 kPa
(153 psi) 1207 kPa
(175 psi) 1007 kPa
(146 psi) 758 kPa
(110 psi) 1214 kPa
(176 psi) 910 kPa
(132 psi) 1420 kPa
(206 psi) 1062 kPa
(154 psi) 1627 kPa
(154 psi) 1220 kPa
(177 psi) 1020 kPa
(148 psi) 765 kPa
(111 psi) 1227 kPa
(178 psi) 917 kPa
(133 psi) 1434 kPa
(208 psi) 1075 kPa
(156 psi) 1641 kPa
(238 psi) 1227 kPa
(178 psi) 1034 kPa
(150 psi) 779 kPa
(113 psi) 1241 kPa
(180 psi) 931 kPa
(135 psi) 1448 kPa
(210 psi) 1083 kPa
(157 psi) 1655 kPa
(240 psi) 1241 kPa
(180 psi) 1048 kPa
(152 psi) 786 kPa
(114 psi) 1255 kPa
(182 psi) 936 kPa
(136 psi) 1462 kPa
(212 psi) 1089 kPa
(158 psi) 1669 kPa
(242 psi) 1248 kPa
(181 psi) 1062 kPa
(154 psi) 793 kPa
(115 psi) 1269 kPa
(184 psi) 952 kPa
(138 psi) 1476 kPa
(214 psi) 1103 kPa
(160 psi) 1682 kPa
(244 psi) 1262 kPa
(183 psi) 1076 kPa
(156 psi) 807 kPa
(117 psi) 1282 kPa
(186 psi) 965 kPa
(140 psi) 1489 kPa
(216 psi) 1117 kPa
(162 psi) 1696 kPa
(246 psi) 1269 kPa
(184 psi) 1089 kPa
(158 psi) 814 kPa
(118 psi) 1296 kPa
(188 psi) 972 kPa
(141 psi) 1503 kPa
(218 psi) 1124 kPa
(163 psi) 1710 kPa
(248 psi) 1202 kPa
(186 psi) 1103 kPa
(160 psi) 827 kPa
(120 psi) 1310 kPa
(190 psi) 979 kPa
(142 psi) 1517 kPa
(220 psi) 1138 kPa
(165 psi) 1724 kPa
(250 psi) 1289 kPa
(187 psi) 1110 kPa
(161 psi) 834 kPa
(121 psi) 1324 kPa
(192 psi) 993 kPa
(144 psi) 1631 kPa
(222 psi) 1145 kPa
(166 psi) — —Klj . 8 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. WORN RINGS OR DILUTED OIL: When the engine is accelerated (dotted needle), the needle
drops to 0 kPa (0 in- Hg). Upon deceleration, the needle runs slightly above 74 kPa (22 in- Hg).
5. STICKING VALVES: When the needle (dotted) remains steady at a normal vacuum but occasionally flicks (sharp, fast movement) down and back about 13 kPa (4 in- Hg), one or more
valves may be sticking.
6. BURNED OR WARPED VALVES: A regular, evenly- spaced, downscale flicking of the needle
indicates one or more burned or warped valves. Insufficient hydraulic lash adjuster or hydraulic
lash adjuster (HLA) clearance will also cause this reaction.
7. POOR VALVE SEATING: A small but regular downscale flicking can mean one or more valves are not seating.
8. WORN VALVE GUIDES: When the needle oscillates over about a 13 kPa (4 in- Hg) range at idle
speed, the valve guides could be worn. As engine speed increases, the needle will become
steady if guides are responsible.
9. WEAK VALVE SPRINGS: When the needle oscillation becomes more violent as engine rpm is increased, weak valve springs are indicated. The reading at idle could be relatively steady.
10. LATE VALVE TIMING: A steady but low reading could be caused by late valve timing.
11. IGNITION TIMING RETARDING: Retarded ignition timing will produce a steady but somewhat low reading.
12. INSUFFICIENT SPARK PLUG GAP: When spark plugs are gapped too close, a regular, small pulsation of the needle can occur.
13. INTAKE LEAK: A low, steady reading can be caused by an intake manifold or throttle body gasket leak.
14. BLOWN HEAD GASKET: A regular drop of fair magnitude can be caused by a blown head gasket or warped cylinder head- to-cylinder block surface.
15. RESTRICTED EXHAUST SYSTEM: When the engine is first started and is idled, the reading may be normal, but as the engine rpm is increased, the back pressure caused by a clogged
muffler (5230), kinked tail pipe or other concerns will cause the needle to slowly drop to 0 kPa
(0 in-Hg). The needle then may slowly rise. Excessive exhaust clogging will cause the needle to
drop to a low point even if the engine is only idling.
16. When vacuum leaks are indicated, search out and correct the cause. Excess air leaking into the system will upset the fuel mixture and cause concerns such as rough idle, missing on
acceleration or burned valves. If the leak exists in an accessory unit such as the power brake
booster (2005), the unit will not function correctly. Always fix vacuum leaks.
Excessive Engine Oil Consumption
The amount of oil an engine uses will vary with the way the vehicle is driven in addition to normal
engine- to-engine variation. This is especially true during the first 16,100 km (10,000 miles) when a new
engine is being broken in or until certain internal engine components become conditioned. Vehicles
used in heavy- duty operation may use more oil. The following are examples of heavy- duty operation:
z trailer towing applications
z severe loading applications
z sustained high speed operation Klj . 12 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...