2003 FORD MUSTANG differential

4.
CAUTION: Do not damage the aluminum differential housing (4010) while carrying
out these procedures.
Using the special tools, mount the differential housing to a work bench. 1. Attach the special tools to the differential housing with four bolts that retain the differential housing cover to the differential housing.
2. Attach the special tools together with two 3/8 inch x 1- 1/2 inch bolts.
5. Install the special tool by placing the spreader pins in the hole in the Housing Spreader Adapters.
6. Assemble the special tool. 1. Install the special tool.
2. Attach the special tool and position the tip in the Housing Spreader Adapter hole.
7. CAUTION: Overspreading can damage the differential housing.
NOTE: Tighten and loosen the Differential Carrier Spreader screw to normalize the Housing
Spreader Adapters prior to taking the final Dial Indicator reading.
Spread the differential housing to the specification. Klj . 5 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

1. Adjust the special tool to zero.
2. Tighten the screw until the differential housing is spread to the specification.
3. Remove the special tools.
8. CAUTION: Mark the position and location of the differential bearing caps as the
arrows may not be visible. Always install the differential bearing caps in their identical
location and position.
Remove the differential bearing caps. 1. Remove the bolts.
2. Remove the differential bearing caps.
9. CAUTION: Use wood blocks to avoid damaging the differential housing.
Remove the differential assembly. 1. Position wood blocks at the top and bottom of the differential case (4204).
2. Pry the differential assembly and the differential bearing shims (4067) out of the
differential housing.
3. Remove the special tool.
10. CAUTION: Record the torque necessary to maintain rotation of the drive pinion gear Klj . 6 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

through several revolutions prior to removing the rear axle pinion flange (4851).
Remove the rear axle pinion flange. For additional information, refer to
Drive Pinion Flange in
this section.
11. Using a screwdriver, force the rear axle drive pinion seal metal flange up and strike it with a hammer.
12. Using gripping pliers and a hammer, remove the rear axle drive pinion seal (4676).
13. Remove the rear axle drive pinion shaft oil slinger (4670).
14. Using the special tool and a soft- faced hammer, drive the drive pinion gear out of the front
pinion bearing (4621) and remove it through the rear of the differential housing.
15. Remove and discard the differential drive pinion collapsible spacer (4662). Klj . 7 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

16. Using the special tool and a suitable press, remove the pinion bearing (4630).
1. Position the special tool under the pinion bearing.
2. Using a press, remove the pinion bearing.
17. NOTE: Using a micrometer, measure the drive pinion bearing adjustment shim thickness. Use
this measurement as a reference to compare to the shim gauge reading taken prior to installing
the pinion bearing.
Remove the drive pinion bearing adjustment shim (4663).
18. Using a brass drift and a hammer, remove any damaged differential drive pinion bearing cup (4616) (4628) from the differential housing. Tap alternately on each side of the cup to prevent it
from cocking in the bore. Klj . 8 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

19. If the differential ring gear backface runout measurement, taken at the beginning of this
procedure, did not exceed the specification, proceed to Final disassembly in this procedure. If
the differential ring gear backface runout measurement, taken at the beginning of this
procedure, exceeded the specification, the cause may be a warped differential ring gear, a
damaged differential case, or loss of differential bearing preload. Proceed to Excessive
differential ring gear backface runout in this procedure to verify the cause of the excessive
runout.
Excessive differential ring gear backface runout 20. Place the differential assembly with the differential bearings (4221) and the differential bearing cups (4222) in the differential housing.
21. Install a differential bearing shim of the thickness shown on the LH side of the differential case.
22. Install the LH differential bearing cap finger- tight. Klj . 9 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

23.
NOTE: Apply pressure toward the left side to fully seat the differential bearing cup.
Install progressively larger differential bearing shims on the RH side until the largest differential
bearing shim selected can be assembled with a slight drag feel.
24. Install the RH differential bearing cap. zTighten both bearing caps to specification.
25. Rotate the differential assembly to make sure it turns freely. Klj . 10 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

26. Using the special tool, measure and record the differential ring gear backface runout.
zIf the runout does not exceed the specification, the cause of the original excessive runout
was due to a loss of differential bearing preload. Proceed to Final disassembly in this
procedure.
z If the runout exceeds the specification, proceed as follows.
„Remove the special tool.
27. Remove the differential assembly.
28. Remove the bolts.
29. CAUTION: Do not damage the bolt hole threads.
Insert a punch in the bolt holes and drive off the differential ring gear. Klj . 11 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

30. Install the differential case. Rotate the differential case to seat the differential bearings.
31. Using the special tool, measure the differential case flange runout.
zIf the runout does not exceed the specification, the cause of the original excessive runout
is the differential ring gear. Remove the differential case. Discard the differential ring gear
and the drive pinion gear. Proceed to Final disassembly in this procedure.
z If the runout exceeds the specification, the differential ring gear is true and the concern is
due to either differential case/differential bearing damage. Remove the differential case.
Discard the differential bearings/differential case. Proceed to Final disassembly in this
procedure.
„Remove the special tool.
Final disassembly 32. If not done previously, remove the bolts. Klj . 12 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...