2003 FORD MUSTANG differential

REMOVAL AND INSTALLATION
Axle Housing
Removal
1. CAUTION: The vehicle must be on level ground and at curb height.
Mark the rear shock absorbers relative to their protective sleeve. zDuring installation, raise the suspension to this reference mark before tightening the
suspension component fasteners.
SECTION 205-
02C: Rear Drive Axle/Differential — Ford 8.8-Inch IRS 2003 Mustang Workshop Manual Special Tool(s)
Plug Set, Differential
205-
294 (T89P-4850- B) Protector, Differential Seal
(Pair)
205-
461 Remover, Halfshaft
205-
475 Remover, Steering Arm
211-
003 (T64P-3590- F) Klj . 1 ba
142003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

17.
NOTE: Mark the new cam bolt in the same position as the old one for assembly reference
before discarding the old bolt.
Disconnect the knuckle from upper suspension arm and bushing. 1. Remove and discard the nut and bolt.
2. Disconnect the knuckle from the upper suspension arm and bushing.
18. CAUTION: The crown on the tool forks must face away from the differential
housing. Position the special tool correctly between the CV joint and the differential
housing so as not to damage the differential seal.
Using the special tool, exert enough pressure to overcome the circlip and separate the CV joint
from the differential side gear.
19. Install the special tool.
20. Remove the halfshaft and knuckle assembly from the vehicle. Klj . 5 ba
142003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

21. Insert the special tool into the housing bore.
22. Remove the other halfshaft and knuckle assembly as described in the previous steps.
23. Support the differential housing (4010) with a transmission jack.
24. Remove the bolts.
25. Remove the nuts and bolts. Klj . 6 ba
142003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

8.
CAUTION: Differential seal damage will occur if installing the halfshaft without the
special tool.
Install the special tool.
9. Position the halfshaft for installation.
10. Seat the CV joint stub shaft in the differential side gear. 1. Slide the stub shaft into the differential housing until the shaft splines are past the differential seal.
2. Remove the special tool.
3. Align the stub shaft splines and the side gear splines, and slide the stub shaft into the gear until it seats.
„When seated, the axle circlip will lock the stub shaft in the differential side gear.
Check the circlip engagement by attempting to pull the inboard CV joint out of the
differential side gear. If the circlip has not seated, push the CV joint inward until
the circlip is fully engaged in the differential side gear. Klj . 9 ba
142003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DISASSEMBLY AND ASSEMBLY
Axle
SECTION 205-
02C: Rear Drive Axle/Differential — Ford 8.8-Inch IRS 2003 Mustang Workshop Manual Special Tool(s)
2-
Jaw Puller
205- D072 (D97L-4221- A) or
equivalent Adapter for 205-
S127
205- 105 (T76P-4020- A3) Bearing Preload Tool
205-
395 (T93P-4220- A) Plate, Bearing/Oil Seal
205-
090 (T75L-1165- B) Gauge, Clutch Housing
308-
021 (T75L-4201- A) Holding Fixture, Drive Pinion
Flange
205-
126 (T78P-4851- A) Installer, Drive Pinion Flange
205-
002 (TOOL- 4858-E) or
equivalent Dial Indicator Gauge
100-
D005 (D78P-4201- G) or
equivalent Klj . 1 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Dial Indicator Gauge with
Holding Fixture
100-
002 (TOOL- 4201-C) or
equivalent Spreader, Differential Carrier
205-
001 (TOOL- 4000-E) or
equivalent Installer, Differential Side
Bearing
205-
010 (T57L-4221- A2) Adapter for 205-
S127
205- 110 (T76P-4020- A10) Adapter for 205-
S127
205- 129 (T79P-4020- A18) Gauge Tube, Drive Pinion
205-
336 (T93P-4020- A) Adapter for 205-
S127
205- 111 (T76P-4020- A11) Spreader, Differential Housing
(Plate)
205-
335 (T93P-4000- A) Klj . 2 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Gauge, Differential Bearing
205-
338 (T93P-4222- A) Installer, Drive Pinion Bearing
Cone
205-
005 (T53T-4621- C) Installer, Drive Pinion Bearing
Cup
205-
024 (T67P-4616- A) Protector, Drive Pinion Thread
205-
460 Installer, Drive Pinion Oil Seal
205-
133 (T79P-4676- A) Gauge, Differential Bearing
205-
339 (T93P-4222- B) Adapter for 205-
S127
205- 109 (T76P-4020- A9) Step Plate
205-
D061 (D83T-4205- C2) or
equivalent Klj . 3 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Disassembly
Initial disassembly
1. Remove the differential housing cover (4033) and drain the lubricant into a suitable container.
2. Wipe the lubricant from the internal working parts and inspect the parts for wear and damage.
3. Using the special tool, measure and note the differential ring gear backface runout. zRemove the special tool. Gauge, Differential Clutch
205-
135 (T80P-4946- A) Gauge, Differential Clutch
Torque
205-
013 (T59L-4204- A) Remover, Bearing
205-
055 (T71P-4621- B) Holding Fixture, Transmission
307-
003 (T57L- 500-B) Klj . 4 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...