2003 DAEWOO MATIZ cooling
[x] Cancel search: coolingPage 791 of 1184
MANUAL CONTROL HEATING, VENTILATION, AND AIR CONDITIONING SYSTEM 7B–9
DAEWOO M-150 BL2
Insufficient Cooling Diagnosis (Cont’d)
Step Action Value(s) Yes No
12
Repair the electrical circuit to the A/C compressor
clutch coil.
Does the A/C clutch engage?
–
Go to Step 20Go to Step 13
13Replace the A/C compressor clutch coil.
Does the A/C clutch engage?–Go to Step 9Go to Step 10
14
Important: Perform this test under garage condi-
tions; 21-32C (70-90F) and no sun load. Follow
this test carefully for accurate results.
1. Close all of the windows and the doors of the
vehicle.
2. Set the A/C controls to the following positions:
The A/C switch to the ON position.
The fresh air control switch to fresh air.
The blower motor to 4.
The temperature to full cold.
3. Start the engine and follow it to run at idle for
5 minutes.
4. Feel the evaporator inlet and outlet pipes.
Is there a noticeable difference in the temperature of
the evaporator inlet and outlet pipes?
–
Go to Step 16Go to Step 15
15
1. Recover the A/C system refrigerant.
2. Replace the expansion valve as needed.
3. Evacuate and recharge the A/C system.
4. Check the A/C system for leaks.
5. Note the discharge air temperature with the A/C
ON.
Is the discharge temperature normal?
–
Go to Step16Go to Step 18
16
Feel the liquid pipe between the condenser and the
expansion valve.
Is the pipe cold?
–
Go to Step 19Go to Step 17
17
1. Remove the restriction of the high pressure side.
2. Check the A/C system for leaks.
Is the repair complete?
–
System OK
–
18
1. Recover the A/C system refrigerant.
2. Evacuate and recharge the A/C system.
3. Check the A/C system for leaks.
Is the repair complete?
–
System OK
–
19
1. Run the engine at 3,000 rpm.
2. Close all of the windows and doors of the vehicle.
3. Set the A/C controls to the following positions:
The A/C switch to the ON position.
The fresh air control switch to fresh air.
The blower motor to 4.
The temperature to full cold.
4. Turn the A/C switch ON and OFF every
20 seconds for 3 minutes.
Are the A/C compressor high and the low side
pressures within the specified value of each other?
Low Side
Pressure:
200 kPa
(29 psi)
High Side
Pressure:
1,500 kPa
(217.5 psi)
System OKGo to Step 22
Page 792 of 1184
7B–10 MANUAL CONTROL HEATING, VENTILATION, AND AIR CONDITIONING SYSTEM
DAEWOO M-150 BL2
Insufficient Cooling Diagnosis (Cont’d)
Step Action Value(s) Yes No
20
1. Turn the ignition switch OFF.
2. Turn the A/C switch to the OFF position.
3. Attempt to turn the clutch driver (not the pulley).
Can you turn the clutch driver freely by hand?
–
Go to Step 23Go to Step 21
21
1. Recover the A/C system refrigerant.
2. Replace the A/C compressor.
3. Evacuate and recharge the A/C system.
Is the repair complete?
–
System OK
–
221. Add the refrigerant R–134a.
Does the cooling performance improve?–System OKGo to Step 23
23
1. Recover the A/C system refrigerant.
2. Replace the compressor.
3. Evacuate and recharge the A/C system.
4. Check the A/C system for leaks.
Is the repair complete?
–
System OK
–
Page 794 of 1184
7B–12 MANUAL CONTROL HEATING, VENTILATION, AND AIR CONDITIONING SYSTEM
DAEWOO M-150 BL2
Pressure Test Chart (R-134a System) (Cont’d)
Condition Related Symptons Probable Cause Correction
Suction Pressure
Abnormally High
Low pressure hose and
check joint are cooler
The expansion valve is
opened for too long.
Replace the expansion
valve.
Abnormally High
check joint are cooler
than the temperature
around the evaporator.
opened for too long.
valve.
Suction pressure is
lowered when the con-
denser is cooled by
water.
There is excessive
refrigerant in the system.
Recover, evacuate, and
recharge the system.
Suction and Dis-
charge Pressure Reduced airflow
through the condenser. The condenser or the
radiator fins are clogged. Clean the condenser and
the radiator.
Abnormally High
The radiator cooling fans
are not working properly.
Check the voltage and
the radiator cooling fan
rpm.
Check the fan direction.
Condenser is
excessively hot.
There is excessive
refrigerant in the system.
Recover, evacuate, and
recharge the system.
Suction and Dis-
charge Pressure
Abnormally Low
Low pressure hose and
metal end areas are
cooler than the
evaporator.
Clogged or kinked low
pressure hose.
Repair or replace the low
pressure hose.
Temperature around the
expansion valve is low
compared to that
around the
receiver/drier.
The high pressure line is
clogged.
Repair or replace the
high pressure line.
Refrigerant Leaks
The compressor clutch
is dirty.
The compressor shaft seal
is leaking.
Repair or replace the
compressor.
The compressor bolts
are dirty. Leaking around a
compressor housing bolt. Tighten the bolt(s) or
replace the compressor.
The compressor gasket
is wet with oil.
The compressor gasket is
leaking.
Repair or replace the
compressor.
–
Poor tightening in the
system.
Retighten the connection
(coupling, bolt etc.)
– O–ring is faulty. Replace the O–ring.
Page 799 of 1184
MANUAL CONTROL HEATING, VENTILATION, AND AIR CONDITIONING SYSTEM 7B–17
DAEWOO M-150 BL2
SERVICEABLE
COMPONENTS
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
CONTROL ASSEMBLY AND
CONTROL CABLES
To remove the control assembly and control cables, re-
fer to Section 7A, Heating and Ventilation System (With-
out Air Conditioning).
BLOWER MOTOR AND COOLING
HOSE
To remove the blower motor and cooling hose, refer to
Section 7A, Heating and Ventilation System (Without Air
Conditioning).
BLOWER RESISTOR
To remove the blower resistor, refer to Section 7A, Heat-
ing and Ventilation System (Without Air Conditioning).
BLOWER MOTOR SWITCH
To remove the blower motor switch, refer to Section 7A,
Heating and Ventilation System (Without Air Condition-
ing).
Page 812 of 1184
7B -- 30 MANUAL CONTROL HEATING, VENTILATION, AND AIR CONDITIONING SYSTEM
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application
Unit
Description
Compressor
--
SP--10.4PK
Receiver--Dryer
--
AL R/DRIER
Refrigerant
Type
--
R--134a System
Refrigerant
Capacity
g
500 (RHD : 530)
RefrigerantOilinA/CSystem
Type
--
RL 244 PAG OIL RefrigerantOilinA/CSystem
Capacity
cc
150
A/C Cooling Capacity (Airflow rate 8.7 kg/min)
Kcal/h
5,500
Refrigerant Pressure in A/C Sys-
tem(Engine Idle, Fresh Air 30_C
(86_F)AmbientTemperature
Low Pressure Side
kPa (psi)
200 (2.9)
(86_F),AmbientTemperature
25_C--35_C(77_F--95_F), Tempera-
ture to Full Cold)
High Pressure Side
kPa (psi)
1,500 (217.5)
A/C Compressor ON/OFF Condition
(Refer toSection 1F, Engine Controls
AbouttheA/CCompressorON/OFF
Evaporator Therm-
istor Temperature
_C(_F)
2.45(36.81)
1.0 (34.2)
ON
OFF
About theA/CCompressorON/OFF
Condition According to Engine Oper-
ating Status)
Dual Cut Switch
Pressure
kPa
205--245
180--220
ON
OFF300--400
240--280
FASTENER TIGHTENING SPECIFICATIONS
Application
NSm
Lb-Ft
Lb-In
Compressor Upper Bracket Bolts
20
15
--
Compressor Front Head-to-Rear Head Through-Bolt
22
16
--
High Pressure Pipe Line (Compressor→Condenser) Bolt
23
17
--
High Pressure Pipe Line (Compressor→Condenser) Fitting
23
17
--
High Pressure Pipe Line (Compressor→Condenser) Clamp Nut
5
--
44
Receiver--Dryer Flange Nut
14
10.5
--
High Pressure Pipe Line (Condenser→Receiver--Dryer) Fitting Nut
14
10.5
--
High Pressure Pipe Line (Receiver--Dryer→Evaporator) Fitting Nut
14
10.5
--
High Pressure Pipe Line(Receiver--Dryer→Evaporator) Clamp Nut
5
--
44
Low Pressure Pipe Line (Evaporator→Compressor) Fitting Nut
14
10.5
--
Low Pressure Pipe Line (Evaporator→Compressor) Clamp Nut
5
--
44
Low Pressure Pipe Line(Evaporator→Compressor) Compressor Bolt
23
17
--
Dual Cut Switch
13
--
11 5
Receive--Dryer Bracket--to--Body Bolts
5
--
44
Receive--Dryer Bracket Bolt
5
--
44
Expansion Valve Coupling (Receiver--Dryer→Expansion Valve)
17
13
--
Expansion Valve Coupling (Expansion Valve→Evaporator)
22
16
--
Compressor Shaft Bolt
13
--
11 5
Condenser Mounting Nuts
4
--
36