2003 DAEWOO MATIZ Ignition

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–73
DAEWOO M-150 BL2
D110B009A
3. Install the floor console. Refer to Section 9G, Interior
Trim.
4. Connect the negative battery cable.
5. Check for proper operation of the system.

Turn the ignition ON while watching the supple-
mental inflatable restraints warning lamp.

The warning lamp should turn ON for about 4 sec-
onds, and then turn OFF.

DAEWOO M-150 BL2
SECTION 9A
BODY WIRING SYSTEM
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9A-2. . . . . . . . . . . . . . . . . .
How to Read Electrical Wiring Diagram 9A-2. . . . . . .
How to Check Terminal Number of Connector 9A-4.
Special Tools and Equipment 9A-5. . . . . . . . . . . . . . .
Special Tools Table 9A-5. . . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 9A-6. . . . . . . . . . .
Wire Color Chart 9A-6. . . . . . . . . . . . . . . . . . . . . . . . . .
Power Distribution Schematic 9A-7. . . . . . . . . . . . . . .
Relay & Fuse Box Locator (Engine Room) 9A-8. . . .
Fuse Box Locator
(Passenger Compartment) 9A-9. . . . . . . . . . . . . . . . Fuse Chart 9A-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Harness Routing 9A-11. . . . . . . . . . . . . . . . . . . .
Engine Harness Routing 9A-12. . . . . . . . . . . . . . . . . . .
Instrument Harness Routing 9A-14. . . . . . . . . . . . . . .
Airbag Harness Routing 9A-16. . . . . . . . . . . . . . . . . . .
Body Harness Routing 9A-17. . . . . . . . . . . . . . . . . . . .
Front Door Harness Routing 9A-19. . . . . . . . . . . . . . .
Rear Door Harness Routing 9A-20. . . . . . . . . . . . . . . .
Tailgate Harness Routing 9A-21. . . . . . . . . . . . . . . . . .

9A–10 BODY WIRING SYSTEM
DAEWOO M-150 BL2
FUSE CHART
FuseRating/ SourceCircuit
Ef1 (Engine Fuse)50ABATABS
Ef240ABATIgnition Switch, Instrument Panel Fuse Block
(F5, F11 ~ F13)
Ef310ABATFuel cut-off Switch (Inertia Switch)
Ef410AIGN 1Fuel, EBCM, Generator, VSS, Fuel Pump Relay, Main Relay,
Ignition Coil
Ef5––Not Used
Ef620ABATBlower Motor
Ef715ABATRear Window Defogger
Ef810ABATHeadlamp Hi Beam, Right Side
Ef910ABATHeadlamp Hi Beam, Left Side
Ef1010ABATHeadlamp Lo Beam, Right Side
Ef1110ABATHeadlamp Lo Beam, Left Side
Ef1210A58Tail and Illumination Lamps, Right Side
Ef1310A58Tail and Illumination Lamps, Left Side
Ef1410ABATA/C Compressor
Ef1530ABATRadiator Fan
Ef1610A–Spare
Ef1710ABATHorn
Ef1820ABATHeadlamp Relay, Hi Beam Passing, DRL Module
Ef1915ABATECM, Main Relay
Ef2015ABATFront Fog Lamp
Ef2115A–Spare
F1 (Fuse)10AIGN 1Cluster, Clock, IMMO, Anti-Theft Control Unit,
DRL Relay
F210AIGN 1SDM
F325AIGN 1Hazard Switch, DRL Module
F410AIGN 1Turn Signal Lamp
F515ABATStop Lamp
F610AACCAudio
F720AACCCigar Light
F815AIGN 2Wiper
F915AIGN 2Rear Wiper Motor, Front & Rear Washer, Backup Lamp
F1010AIGN 2Auto Miror Switch
F1110AEf2IMMO, Audio, Room Lamp
F1215AEf2Hazard, Clock
F1320AEf2Anti-Theft Control Unit, Door Lock
F1420ASTStarter Motor

DAEWOO M-150 BL2
SECTION 9B
LIGHTING SYSTEMS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9B-2. . . . . . . . . . . . . . . . . .
Headlamps and Parking Lamps 9B-2. . . . . . . . . . . . .
Front Turn Signal Lamps 9B-2. . . . . . . . . . . . . . . . . . .
Rear Fog Lamp 9B-2. . . . . . . . . . . . . . . . . . . . . . . . . . .
Taillamps 9B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
License Plate Lamp 9B-2. . . . . . . . . . . . . . . . . . . . . . . .
Interior Courtesy Lamp 9B-2. . . . . . . . . . . . . . . . . . . . .
Backup Lamp(s) 9B-2. . . . . . . . . . . . . . . . . . . . . . . . . . .
Daytime Running Lamps (DRL)
(W/Europe Only) 9B-2. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedures 9B-3. . . . .
Headlamps 9B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal Lamps and Hazard Lamps 9B-4. . . . . . .
Stoplamps and Interior Courtesy Lamp 9B-5. . . . . . .
Rear Fog Lamp 9B-6. . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9B-7. . . . . . . . . . . . . . . . . . . . . . . . .
Headlamps 9B-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal Lamps 9B-8. . . . . . . . . . . . . . . . . . . . . . . .
Side Turn Signal Lamps 9B-8. . . . . . . . . . . . . . . . . . . .
Taillamps Assembly 9B-9. . . . . . . . . . . . . . . . . . . . . . . .
Front Fog Lamp 9B-9. . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog/Backup Lamp(s) 9B-10. . . . . . . . . . . . . . . . .
Center High-Mounted Stoplamp 9B-11. . . . . . . . . . . . CHMSL Mounting Bracket 9B-12. . . . . . . . . . . . . . . . .
License Plate Lamps 9B-12. . . . . . . . . . . . . . . . . . . . . .
Door Jamb Switch 9B-13. . . . . . . . . . . . . . . . . . . . . . . .
Interior Courtesy Lamp 9B-13. . . . . . . . . . . . . . . . . . . .
Daytime Running Lamp Module
(W/Europe Only) 9B-14. . . . . . . . . . . . . . . . . . . . . . .
Ashtray Lamp 9B-14. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage Room Lamp 9B-15. . . . . . . . . . . . . . . . . . . . .
Specifications 9B-16. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bulb Usage Chart 9B-16. . . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 9B-17. . . . . . . . . .
Backup Lamp(s) Circuit 9B-17. . . . . . . . . . . . . . . . . . .
Headlamps Circuit 9B-18. . . . . . . . . . . . . . . . . . . . . . . .
Headlamp Leveling Circuit 9B-19. . . . . . . . . . . . . . . . .
Tail and Licence Plate Lamps Circuit 9B-20. . . . . . . .
Stoplamps Circuit 9B-21. . . . . . . . . . . . . . . . . . . . . . . .
Turn and Hazard Lamps Circuit 9B-22. . . . . . . . . . . .
Interior Courtesy Lamp Circuit 9B-23. . . . . . . . . . . . . .
Front Fog Lamp Circuit 9B-24. . . . . . . . . . . . . . . . . . . .
Rear Fog Lamp Circuit 9B-25. . . . . . . . . . . . . . . . . . . .
Dimmer Control Circuit (Except W/Europe) 9B-26. .
Daytime Running Lamps Circuit
(W/Europe Only) 9B-27. . . . . . . . . . . . . . . . . . . . . . .

9B – 2 LIGHTING SYSTEMS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
HEADLAMPS AND PARKING LAMPS
The headlamps are controlled by the multifunction lever
located on the left side of the steering column. They will
come on with the ignition switch in any position. Turning
the headlamp switch to the first position turns on the
parking lamps, the license plate lamps and the instru-
ment panel illumination. Turning the switch to the sec-
ond position turns on all of the previous lamps and the
headlamps. Turning the switch to the off position turns
off all the lamps.
The parking lamps can be turned on by turning the light-
ing switch to the first position. The parking lamps can be
turned off by turning the switch to the OFF position.
Headlamp high beam and low beam are also controlled
by this lever. When the headlamps are on, pushing the
lever away from the driver until the switch clicks
changes the lamp from low beam to high beam. An indi-
cator lamp on the instrument cluster assembly will come
on when the high beam headlamps are on. To return the
headlamps to low beam, pull the lever toward the driver.
The headlamps must be aimed for proper illumination of
the road. Headlamp aim should be checked whenever a
new headlamp assembly is installed or service repairs to
the front end area may have disturbed the headlamp as-
sembly or its mountings.
FRONT TURN SIGNAL LAMPS
When the turn signals are activated, the side turn signal
lamps flash to signal a turn. The turn signal works only
when the ignition switch is on.
The turn signals are controlled by the light switch on the
left side of the steering column. Moving the lever all the
way up or down (past the detent) will turn on the turn sig-
nals. When the turn is completed, the lever will return to
horizontal and the turn signals will stop flashing.
For changing lanes or shallow turns where the steering
wheel does not turn far enough to cancel the signal,
move the signal only to the first detent and hold it there.
When the lever is released, it will return to horizontal and
the turn signal will cancel.
REAR FOG LAMP
The rear fog lamp is incorporated in the drive side tail-
lamp assembly and are controlled by the rear fog lamp
switch on the instrument panel. The rear fog lamp can
be turned on only when headlamps are on.
TAILLAMPS
The taillamps, stoplamps, backup lamp(s), rear fog lamp
(if equipped with) and turn signal lamps are one assem-
bly.
Turning on either the headlamps or the parking lamps
will also turn on the taillamps. When the brake pedal is
pushed, the taillamps will glow brighter to serve as sto-
plamps.
The center high-mounted stoplamp is located in the rear
window and will come on when the brake pedal is
pressed.
LICENSE PLATE LAMPS
The license plate lamps will come on when the head-
lamps or the parking lamps are on. The license plate
lamps are mounted on the rear bumper, above the li-
cense plate.
INTERIOR COURTESY LAMP
The courtesy lamp is located on the headliner just be-
fore the front seats. The lamp switch has three posi-
tions. If the switch is in the center position, the lamp will
go on whenever a door is opened and go off when it is
closed. In the ON position, the lamp will stay on until it is
turned off. In the OFF position, the lamp will not come
on, even when a door is opened.
BACKUP LAMP(S)
The backup lamps are located in the rear combination
lamps. They will come on when the transaxle is shifted
into REVERSE. On a vehicle with a manual transaxle,
they are activated by a reverse switch which is part of
the transaxle.
DAYTIME RUNNING LAMPS (DRL)
(W/Europe Only)
The daytime running lamps (DRL) work in conjunction
with the exterior lamps system. When the ignition switch
is turned to the ”II” position with the light switch off, park-
ing, tail, license plate and instrument panel lights illumi-
nate. And, when the engine is started, the headlamps
(low beam) also come on.
They remain on until the ignition switch is turned off or
the light switch is turned on. They revert to normal op-
eration when the light switch is on.
The daytime running lamps (DRL) is optional.

DAEWOO M-150 BL2
SECTION 9C
HORNS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9C-2. . . . . . . . . . . . . . . . . .
Horn 9C-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9C-3. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 9C-3. . . . . . . . . . . . . . . . . . . . . . . . . . Horn 9C-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 9C-4. . . . . . . . . . .
Horn Wiring System 9C-4. . . . . . . . . . . . . . . . . . . . . . .

DAEWOO M-150 BL2
SECTION 9D
WIPERS / WASHER SYSTEMS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9D-2. . . . . . . . . . . . . . . . . .
Windshield Wiper System 9D-2. . . . . . . . . . . . . . . . . .
Windshield Washer System 9D-2. . . . . . . . . . . . . . . . .
Rear Window Wiper/Washer System 9D-2. . . . . . . . .
Diagnostic Information and Procedures 9D-3. . . . .
Windshield/Rear Window Wiper and Washer
System 9D-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9D-6. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 9D-6. . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield Wiper Arm 9D-6. . . . . . . . . . . . . . . . . . . . .
Rear Window Wiper Arm 9D-6. . . . . . . . . . . . . . . . . . .
Windshield Wiper Motor 9D-7. . . . . . . . . . . . . . . . . . . .
Rear Window Wiper Motor 9D-8. . . . . . . . . . . . . . . . . . Windshield Wiper Linkage 9D-9. . . . . . . . . . . . . . . . . .
Windshield Wiper Blade 9D-10. . . . . . . . . . . . . . . . . . .
Washer Reservoir 9D-10. . . . . . . . . . . . . . . . . . . . . . . .
Washer Pump 9D-11. . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield Washer Nozzle 9D-12. . . . . . . . . . . . . . . .
Rear Window Washer Nozzle 9D-12. . . . . . . . . . . . . .
Washer Hose 9D-13. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 9D-15. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 9D-15. . . . . . . . . .
Schematic and Routing Diagrams 9D-16. . . . . . . . . .
Windshield/Rear Window Wiper/Washer
System 9D-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DAEWOO M-150 BL2
SECTION 9E
INSTRUMENTATION/DRIVER INFORMATION
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9E-2. . . . . . . . . . . . . . . . . .
Cigar Lighter 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ashtray 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Vents 9E-2. . . . . . . . . . . . . . . . . . . .
Glove Box 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Clock 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster 9E-2. . . . . . . . . . . . . . . . . . . . . . . .
Speedometer/Odometer/Trip Odometer 9E-2. . . . . .
Fuel Gauge 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature Gauge 9E-2. . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster Indicator Lamps 9E-2. . . . . . . . . .
Component Locator 9E-3. . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Assembly 9E-3. . . . . . . . . . . . . . . . .
Instrument Cluster 9E-4. . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedures 9E-5. . . . .
Cigar Lighter 9E-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HVAC Panel Illumination 9E-6. . . . . . . . . . . . . . . . . . .
Digital Clock 9E-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9E-8. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 9E-8. . . . . . . . . . . . . . . . . . . . . . . . . .
Cigar Lighter 9E-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ashtray 9E-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster Trim Panel Vents 9E-9. . . . . . . . .
Digital Clock 9E-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glove Box 9E-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster 9E-11. . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel 9E-12. . . . . . . . . . . . . . . . . . . . . . . . .
Tie–Bar 9E-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster Trim Panel 9E-16. . . . . . . . . . . . . .
Instrument Trim Panel Assembly 9E-16. . . . . . . . . . .
Instrument Cluster Indicator Lamps 9E-19. . . . . . . . .
Speedometer/Odometer/Trip Odometer 9E-19. . . . .
Fuel Gauge/Temperature Gauge 9E-20. . . . . . . . . . .
Specifications 9E-22. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 9E-22. . . . . . . . . .
Instrument Cluster Indicator Lamps
Specifications 9E-22. . . . . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 9E-23. . . . . . . . . .
Instrument Cluster 9E-23. . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Illumination 9E-25. . . . . . . . . . . . . .
Digital Clock 9E-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . .