2003 DAEWOO MATIZ light

ENGINE CONTROLS 1F–27
DAEWOO M-150 BL2
Engine Cranks But Will Not Run (Cont’d)
StepActionValue(s)YesNo
21
1. Check for any damages or poor connection in
ignition wires and repair as needed.
2. Connect the Ei system ignition coil connector and
ECM connector.
3. Check for the presence of spark from all of the
ignition wires.
Is the spark present from all of the ignition wires?
–
Go to Step 2Go to Step 22
22Replace ECM
Is the repair complete?–Go to Step 2–
23
1. Turn the ignition OFF.
2. Connect a fuel pressure gauge.
3. Crank the engine.
Is any fuel pressure present?
–
Go to Step 26Go to Step 24
24
1. Turn the ignition OFF.
2. Disconnect the electrical connector at the fuel
pump.
3. Connect a test light between the fuel pump
terminals 2 and 3.
4. Turn the ignition ON.
5. With the ignition ON, the test light should light for
the time specified.
Is the test light on?
2 sec.Go to Step 25Go to Step 32
25Replace the fuel pump.
Is the repair complete?–Go to Step 2–
26
Is the fuel pressure within the value specified?
380 kPa
(55 psi)
Go to Step 27Go to Step 29
27Check the fuel for contamination.
Is the fuel contaminated?–Go to Step 28Go to Step 41
28
1. Remove the contaminated fuel from the fuel tank.
2. Clean the fuel tank as needed.
Is the repair complete?
–
Go to Step 2
–
29
1. Check the fuel filter for restriction.
2. Inspect the fuel lines for kinks and restrictions.
3. Repair or replace as needed.
4. Measure the fuel pressure.
Is the fuel pressure within the value specified?
380 kPa
(55 psi)
Go to Step 2Go to Step 30
30
1. Disconnect vacuum line from the fuel pressure
regulator.
2. Inspect the vacuum line for the presence of fuel.
3. Inspect the fuel pressure regulator vacuum port
for the presence of fuel.
Is any fuel present?
–
Go to Step 31Go to Step 32
31Replace the fuel pressure regulator.
Is the repair complete?–Go to Step 2–
32
1. Remove the fuel pump assembly from the fuel
tank.
2. Inspect the fuel pump sender and the fuel
coupling hoses for a restriction.
3. Inspect the in-tank fuel filter for restriction.
Is the problem found?
–
Go to Step 33Go to Step 25

1F–28 ENGINE CONTROLS
DAEWOO M-150 BL2
Engine Cranks But Will Not Run (Cont’d)
StepActionValue(s)YesNo
33
Replace the fuel pump sender, the in-tank fuel filter,
and/or the fuel coupling hoses as needed.
Is the repair complete?
–
Go to Step 2
–
34
1. Turn the ignition OFF.
2. Disconnect the electric connector at the fuel
pump.
3. Connect a test light between fuel pump connector
terminal 3 and ground.
4. Turn the ignition ON.
5. With the ignition ON, the test light should
illuminate for the time specified.
Is the test light on?
2 secGo to Step 35Go to Step 36
35
Repair the open circuit between the fuel pump
connector terminal 2 and ground.
Is the repair complete?
–
Go to Step 2
–
36
1. Turn the ignition OFF.
2. Disconnect the fuel pump relay.
3. Turn the ignition ON.
4. Measure the voltage at terminal 30 and 85 of fuel
pump relay.
Is the voltage within the value specified?
11 – 14 VGo to Step 38Go to Step 37
37Repair open or short circuit for power supply.
Is the repair complete?–Go to Step 2–
38
1. Turn the ignition OFF.
2. Disconnect ECM connector.
3. Using an ohmmeter, measure the resistance
between following terminals.

Terminal 10 of ECM and terminal 85 of fuel
pump relay.

Terminal 87 of fuel pump relay and terminal 3
of fuel pump.
Does the resistance within the value specified?
0 ΩGo to Step 40Go to Step 39
39
1. Check for open circuit and fuel cut–off switch.
2. Reset fuel cut-off switch or repair open circuit as
needed.
Is the repair complete?
–
Go to Step 2
–
40Replace the fuel pump relay.
Is the repair complete?–Go to Step 2–
41
1. Turn the ignition OFF.
2. Disconnect the fuel inject harness connectors
from all of the fuel injectors.
3. Turn the ignition ON.
4. Connect test light between fuel injector harness
connector 1 and ground.
5. Repeat step 4 for each of the remaining fuel
injectors.
Does the test light on at all of the fuel injectors?
–
Go to Step 42Go to Step 45

ENGINE CONTROLS 1F–29
DAEWOO M-150 BL2
Engine Cranks But Will Not Run (Cont’d)
StepActionValue(s)YesNo
42
1. Turn the ignition OFF.
2. Connect test light between fuel injector harness
connector 2 and battery positive.
3. Crank the engine.
4. Repeat step 2 and 3 for each of the remaining
fuel injectors.
Does the test light flash for all of the fuel injectors?
–
Go to Step 43Go to Step 46
43
Measure the resistance of each fuel injectors.
Is the resistance within the value specified.
Note: the resistance will increase slightly at higher
temperature.
13.75–15.25
ΩSystem OKGo to Step 44
44
Replace any of the fuel injectors with a resistance
out of specification.
Is the repair complete?
–
Go to Step 2
–
45
1. Inspect the fuse EF19 in engine fuse block.
2. Check for an open between the circuit from
terminal 2 of the three fuel injectors and terminal
87 of main relay.
Is the problem found?
–
Go to Step 48
Go to “Main
Relay Circuit
Check”
46
Measure the resistance between following terminals.

Terminal 1 of injector 1 connector and terminal 30
of ECM connector.

Terminal 1 of injector 2 connector and terminal 58
of ECM connector.

Terminal 1 of injector 3 connector and terminal 89
of ECM connector.
Does the resistance within the specified value?
0 ΩGo to Step 49Go to Step 47
47Repair the open fuel injector harness wire(s).
Is the repair complete?–Go to Step 2–
48Replace the fuse or repair the wiring as needed.
Is the repair complete?–Go to Step 2–
49Replace the ECM.
Is the repair complete?–Go to Step 2–

ENGINE CONTROLS 1F–31
DAEWOO M-150 BL2
No Malfunction Indicator Lamp
StepActionValue(s)YesNo
1
Attempt to start the engine.
Does the engine start?
–
Go to Step 2
Go to “Engine
Cranks But
Will Not Run”
2
1. Turn the ignition OFF.
2. Disconnect the engine control module (ECM)
connector.
3. Turn the ignition ON.
4. Connect a test light between terminal 68 of ECM
connector and ground.
Is the test light on?
–
Go to Step 3Go to Step 6
3Check terminals for damage or poor connection.
Does any problem found?–Go to Step 5Go to Step 4
4
Replace ECM
Is the repair complete?
–
Go to “On
Board
Diagnostic
System Check”
–
5
Repair any damaged terminals or poor connection.
Is the repair complete?
–
Go to “On
Board
Diagnostic
System Check”
–
6Check the fuse F1.
Is the fuse blown?–Go to Step 7Go to Step 8
7
1. Check for a short to ground in the circuit and
repair as needed.
2. Replace the blown fuse.
Is the repair complete?
–
Go to “On
Board
Diagnostic
System Check”
–
8
1. Check for an open circuit between fuse F16 and
terminal 68 of ECM connector and repair as
needed.
2. Check the MIL bulb and replace if blown.
Is the repair complete?
–
Go to “On
Board
Diagnostic
System Check”
–

ENGINE CONTROLS 1F–37
DAEWOO M-150 BL2
Fuel Pump Relay Circuit Check (Cont’d)
StepActionValue(s)YesNo
3
1. Check for an open circuit between fuel pump test
connector and ground G401, and repair as
needed.
2. Check for the fuel cut-off switch and reset or
replace the fuel cut off switch.
Is the repair complete?
–
System OKGo to Step 4
4
1. Turn the ignition OFF.
2. Disconnect the fuel pump relay.
3. Connect a test light between the fuel pump relay
connector terminal 66 and battery positive.
4. Turn the ignition ON.
Is the test light on?
–
Go to Step 6Go to Step 5
5
Check for an open circuit between terminal 66 of fuel
pump relay and battery positive and repair as
needed.
Is the repair complete?
–
System OK
–
6
1. Turn the ignition OFF.
2. Connect a test light between the fuel pump relay
connector terminal 85 and ground.
3. Turn the ignition ON.
Is the test light on?
2 secGo to Step 8Go to Step 7
7
Check for an open circuit between terminal 85 of fuel
pump relay and terminal 10 of ECM, and repair as
needed.
Is the repair complete?
–
System OK
–
8
1. Turn the ignition OFF.
2. Connect a test light between the fuel pump relay
connector terminal 30 and ground.
Is the test light on?
–
Go to Step 10Go to Step 9
9
1. Check the fuse EF19, if blown, repair short circuit
between fuel pump relay 30 terminal.
2. Replace the fuse as needed.
3. Repair an open circuit as needed.
Is the repair complete?
–
System OK
–
10
1. Turn the ignition OFF.
2. Measure the resistance between following
terminals:

Terminal 87 of fuel pump relay and terminal 1
of the fuel cut-off switch(or terminal 1 of
connector C201).
Does the resistance within the value specified.
0 ΩGo to Step 12Go to Step 11
11Repair an open circuit as needed.
Is the repair complete?–System OK–
12Replace the fuel pump relay.
Is the repair complete?–System OKGo to Step 13
13Replace the ECM.
Is the repair complete?–System OK–

ENGINE CONTROLS 1F–39
DAEWOO M-150 BL2
Main Relay Circuit Check
StepActionValue(s)YesNo
1
1. Turn the ignition OFF.
2. Disconnect the engine fuse block fuse EF26.
3. Turn the ignition ON.
4. With a test light connected to the ground, probe
the fuse terminals nearest the main relay for fuse
EF19.
Is the light on at both terminal?
–
System OKGo to Step 2
2Is the light on at only one terminal?–Go to Step 3Go to Step 4
3
Repair the open in the wiring between the main relay
connector terminal 30 and the fuse EF19 as needed.
Is the repair complete?
–
System OK
–
4
1. Turn the ignition OFF.
2. Remove the main relay.
3. Turn the ignition ON.
4. With a test light connected to the ground, probe
the main relay terminals 85 and 30.
Is the light on at both terminals.
–
Go to Step 8Go to Step 5
5
1. Turn the ignition OFF.
2. Check engine fuse block fuse EF19.
Is one or both fuse blown?
–
Go to Step 6Go to Step 7
6
1. Repair short circuit between terminal 87 of main
relay and heated oxygen sensor
2. Replace fuse EF19.
Is the repair complete?
–
System OK
–
7
Repair open circuit between terminal 30 of main
relay and fuse EF19.
Is the repair complete?
–
System OKGo to Step 8
8
1. Turn the ignition OFF.
2. Measure the resistance between following
terminals.

Terminal 86 of main relay and ground.

Terminal 87 of main relay and ground.
Is the resistance within the specified value
0 ΩGo to Step 10Go to Step 9
9Repair open circuit.
Is the repair complete?–System OK–
10Replace the main relay.
Is the repair complete?–System OK–

ENGINE CONTROLS 1F–47
DAEWOO M-150 BL2
Ignition System Check (Cont’d)
StepActionValue(s)YesNo
21
Measure the voltage between the CKP sensor
connector terminal 2 and ground.
Is the voltage within the value specified?
0.95–1.10 VGo to Step 18Go to Step 22
22
Check the wire between the CKP sensor connector
terminal 2 and the ECM connector terminal 24 for an
open or short.
Is the problem found?
–
Go to Step 23Go to Step 11
23
Repair the wire between the CKP sensor connector
terminal 2 and the ECM connector terminal 24.
Is the repair complete?
–
System OK
–
24
1. Turn the ignition OFF.
2. Connect a test light between the EI system
ignition coil connector terminal 2 and ground.
3. Turn the ignition ON.
Is the test light on?
–
Go to Step 27Go to Step 25
25
Check for an open in the wiring between the EI
system ignition coil connector, terminal 1 and the
main relay connector terminal 87.
Is the problem found?
–
Go to Step 26
Go to “Main
Relay Circuit
Check”
26
Repair the open in the wiring between the EI system
ignition coil connector terminal 1 and the main relay
connector terminal 87.
Is the repair complete?
–
System OK
–
27
Check for a damage in the terminal of the EI system
ignition coil connector and repair as needed.
Is the repair complete?
–
System OK
–

ENGINE CONTROLS 1F–49
DAEWOO M-150 BL2
Engine Cooling Fan Circuit Check
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Was the check performed?
–
Go to Step 2
Go to “Euro
On-Board
Diagnostic
System Check.
2
1. Check the fuses EF3 and EF10 in engine fuse
block.
2. Replace the fuse(s) as needed.
Is the fuse(s) OK?
–
Go to Step 3
Go to
“Diagnostic
Aids”
3
1. Turn the ignition OFF.
2. Turn the A/C switch OFF. If equipped.
3. Connect a scan tool to the Data Link Connector
(DLC).
4. Start the engine.
5. The main cooling fan should run at low speed
when the coolant temperature reaches 96C
(205F).
Does the cooling fan run at low speed?
–
Go to Step 4Go to Step 8
4
The cooling fans should run at high speed when the
coolant temperature reaches 100C (212F).
Do the cooling fans run at high speed?
–
Go to Step 5Go to Step 19
5
1. Turn the ignition OFF.
2. Start the engine.
3. Turn the A/C switch ON.
Does the cooling fan runs at low speed?
–
Go to Step 7Go to Step 6
6
1. Diagnose the A/C compressor clutch circuit.
2. Repair the A/C compressor clutch circuit as
needed.
Is the repair complete?
–
System OK
–
7
1. Turn the ignition OFF.
2. Start the engine.
3. Turn the A/C switch ON and raise the rpm.
4. The cooling fan should run at high speed when
the high side A/C pressure reaches 2068 kPa
(300 psi).
Do the cooling fans run at high speed?
–
System OK
–
8
1. Turn the ignition OFF.
2. Disconnect the cooling fan connector.
3. Turn the ignition ON.
4. Connect a test light between terminal 1 of cooling
fan connector and ground.
Is the test light on?
–
Go to Step 9Go to Step 12
9
Connect a test light between terminal 2 of cooling
fan connector and battery positive.
Is the test light on?
–
Go to Step 11Go to Step 10
10
Repair open circuit between terminal 2 of cooling fan
connector and ground.
Is the repair complete?
–
System OK
–
11
Check for a damaged terminals in main cooling fan
connector and repair it or replace the main cooling
fan.
Is the repair complete?
–
System OK
–