2003 DAEWOO MATIZ Oil

1A–10 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
GENERAL DIAGNOSIS (Cont’d)
 Condition Probable cause Correction
Low Oil PressureMalfunction of
Lubrication
Lowered function of the oil
pump.
Replace the pump.
System
Abrasion or damage of the
oil pump relief valve.
Replace the valve.
Engine NoiseValve Noise
Inadequate valve clearance.
Adjust the valve clearance.

Abrasion of valve stem or
guide.
Replace the valve stem or
the guide.

Weak valve spring.
Replace the spring.
Piston, Ring,
Cylinder Noise
Abrasion of the piston, the
ring or the cylinder.
Boring the cylinder or
replace the piston, the ring
or the cylinder.
Connecting Rod
Noise
Abrasion of the connecting
rod bearing.
Replace the bearing.

Loosened the connecting rod
nut.
Tighten to the specified
torque.
Crankshaft
Noise
Abrasion of the crankshaft
bearing.
Replace the bearing.

Abrasion of the crankshaft
journal.
Grind or replace the
crankshaft journal.

Loosened bearing cap bolt.
Tighten to the specified
torque.

Excessive clearance of the
crankshaft thrust bearing.
Adjust or replace.

Low oil pressure.
Refer to “Low Oil Pressure”
in this section.

GENERAL ENGINE INFORMATION 1A–11
DAEWOO M-150 BL2
CHECKING ENGINE FLUID LEVEL
Check the engine fluid level or condition. If needed, refill
or replace the oil.
Check the engine oil level within engine normal operat-
ing temperature as follows ;
1. After stopping the engine, wait for a few minutes to
accumulate oil into the oil pan.
2. After pulling out the oil level gauge (a), check the oil
level.
3. Clean the oil level gauge and insert the gauge into
guide.
4. After pulling out the oil level gauge again, recheck the
oil level and insert the gauge into guide again.
Important: Oil level should be between “MIN” mark and
“MAX” mark.
5. If oil level is below the “MIN” mark, refill engine oil as
much as the demanded quantify.
Important: If checking oil level under the engine cold
condition, oil is not accumulated into oil pan quickly and
correct level checking can not be performed. Therefore,
wait until temperature reaches the normal operating
condition and check the engine oil level.
D102A301
CHANGING ENGINE OIL OR OIL
FILTER
Tools Required
09915–47341 Oil Filter Wrench.
When checking engine oil level or condition, if needed,
change engine oil (including the filter) as follows ;
1. After stopping the engine, wait for a few minutes to
accumulate oil into the oil pan.
2. Remove the oil filter cap (b).3. Remove the oil drain plug (c) and draw oil off.
D102A302
4. After drawing oil completely, tighten the oil drain plug
to 30–40 Nm (22–30 lb-ft).
5. Replace the oil filter using the oil filter wrench
09915–47341 (d).

Remove the air cleaner/resonator/snorkel as-
sembly.

After removing the bolts, remove the heat
shield.

Loosen the power steering pump cap screw and
pull the power steering hose into the front.

Remove the oil filter.
Important: Whenever changing engine oil, replace the
oil filter. When replacing new oil filter, apply engine oil on
oil filter sealing.
D102A303

1A–14 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS
 Application Description
  Maximum Speed 144 km/h (90 mph)
 Vehicle Capacity Gradeability 0.420 tan θ
 
Vehicle Capacity
 Minimum Turning Radius 4.5 m (14.8 ft)
  Bore × Stroke 68.5 × 72.0 mm (2.70 × 2.83 inch)
  Displacement 796 cm3 (48.6 in3)
  Compression Ratio 9.3 : 1
  Maximum Power 37.5 KW (6,000 rpm)
 
Engine Information
 Maximum Torque 68.6 Nm (50.59 lb-ft) (at 4,600 rpm)
Ignition Timing (Ignition Sequence)5 BTDC (1–3–2) / 10 BTDC (1–3–2)   
Air Conditioning System (ON)
 
1,000 ± 50 rpm  Idle Speed Air Conditioning System (OFF) 950 rpm  Engine Overhead Cam L–3 
 
 
 Ignition Type
 
 Direct Ignition System (DIS) /
High Energy Ignition (HEI)
  Distributor Optical Sensor Type
  Starter SD 80
   Unleaded BPR5EY–11, RN9YC4, WR8DCX
  Spark–Plug Leaded BPR5EY, RN9YC, WR8DC
  Fuel Injection Type MPI
  Fuel Pump Electric Motor Pump
Engine Part TypeFuel FilterCartridge Engine Part Type 
Lubricating Type
 
Forced Feed Type  Oil Pump Rotary Pump Type  Cooling Type Forced Water Circulation  Radiator Cross – Flow  Water Pump Centrifugal  Thermostat Pellet Type
  Air Cleaner Element Non Woven Fablic
  Muffler Catalytic Converter, Closed Circuit
  Battery MF
Engine PartEngine OilSJ Grade
SAE 5W30, SAE 10W30, SAE 15W40
CapacityRefrigerantFour Seasons   
Engine Disassembly
 
3.0 L (3.17 qt)   Oil Change (Including filter) 2.7 L (2.85 qt)  Engine Oil Oil Change (Not including filter) 2.5 L (2.64 qt)   Oil Level Gauge 1 L (1.06 qt) (MIN to MAX)  Coolant 3.8 L (4.02 qt) Engine Information Battery 12V–35 AH, 246 CCA
 Engine Information  

Generator

65 A
  Starter 0.8 kW
   Output Capacity 90 – 133 Lph
  Fuel Pump Output Pressure 380 kPa (55.1 Psi)
  Fuel Tank Capacity 35 L (9.2 gal), 38 L (10 gal)

DAEWOO M-150 BL2
SECTION 1B
SOHC ENGINE MECHANICAL
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 1B-2. . . . . . . . . . . . . . . . . .
Engine Type 1B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Lubrication 1B-2. . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Valve Train 1B-2. . . . . . . . . . . . . .
Engine Block 1B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crankshaft 1B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Rod 1B-3. . . . . . . . . . . . . . . . . . . . . . . . . . .
Piston, Piston Ring and Piston Pin 1B-3. . . . . . . . . . .
Timing Belt and Pulley 1B-4. . . . . . . . . . . . . . . . . . . . .
Engine Mount 1B-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component Locator 1B-5. . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head 1B-5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Block 1B-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manifold & Air Flow System 1B-7. . . . . . . . . . . . . . . . .
Timing Belt & Engine Mount 1B-8. . . . . . . . . . . . . . . .
Diagnostic Information and Procedure 1B-9. . . . . . .
Compression Pressure Check 1B-9. . . . . . . . . . . . . . .
Oil Pressure Check 1B-9. . . . . . . . . . . . . . . . . . . . . . . .
Adjustment of Valve Clearance 1B-10. . . . . . . . . . . . .
Ignition Timing Check and Adjustment
(Typical) 1B-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valve Timing Check and Adjustment 1B-12. . . . . . . .
Repair Instructions 1B-14. . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 1B-14. . . . . . . . . . . . . . . . . . . . . . . . . Air Filter Assembly 1B-14. . . . . . . . . . . . . . . . . . . . . . .
Air Filter Element 1B-15. . . . . . . . . . . . . . . . . . . . . . . . .
Positive Crankcase Ventilation (PCV) Hose
and Valve 1B-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intake Manifold 1B-16. . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold (Typical) 1B-18. . . . . . . . . . . . . . . . .
Exhaust Manifold (Euro III) 1B-20. . . . . . . . . . . . . . . .
Timing Belt 1B-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pan 1B-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump 1B-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distributor Case 1B-26. . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Gasket 1B-28. . . . . . . . . . . . . . . . .
Engine Mount Damping Block 1B-32. . . . . . . . . . . . . .
Engine Mount Front Damping Bush 1B-34. . . . . . . . .
Engine Assembly 1B-35. . . . . . . . . . . . . . . . . . . . . . . . .
Unit Repair 1B-47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Valve Train
Components 1B-47. . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Block Components 1B-59. . . . . . . . . . . . . . . . .
Specifications 1B-71. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Specifications 1B-71. . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 1B-73. . . . . . . . . .
Special Tools 1B-75. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools Table 1B-75. . . . . . . . . . . . . . . . . . . . . . .

1B – 2 SOHC ENGINE MECANICAL
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
ENGINE TYPE
The engine is 4-cycle, water-cooled, in-line 3 cylinders
with displacement of 796cc (68.5×72.0mm) (2.70×
2.83 in.).
Engine model
(Specifications)F8C Type SOHC /
2 Valve (MPI)
Maximum power (kw/rpm)37.5 / 6,000
Maximum torque (N
m/rpm)68.6 / 4,600
Compression ratio9.3 : 1
D102B001
ENGINE LUBRICATION
The engine lubrication is of the wetsump method to draw
up the oil forced by the oil pump. The oil pump is of a
trochoid type, and mounted on crankshaft at crankshaft
pulley side (a). Oil is drawn up through oil pump pickup
tube (b) and passed through pump (c) to oil filter (d). The
filtered oil flows into two paths in engine block. In one
path (e), oil reaches crankshaft journal bearings. Oil
from crankshaft journal bearings is supplied to connect-
ing rod bearings by means of intersecting passages
drilled in crankshaft, and then injected from a small hole
provided on big end of connecting rod to lubricate piston
(f), rings, and cylinder wall. In another path (g), oil goes
up to cylinder head and lubricates rocker arm (i), valve
(j), camshaft (k), etc. through the oil hole provided on the
rocker arm shaft (h).
D102B002
CYLINDER HEAD AND VALVE TRAIN
The cylinder head is made of cast aluminum alloy for
better strength in hardness with lightweight, and cam-
shaft (k) and rocker arm shaft (h) arranged in-line sup-
port.
D102B003
The combustion chambers are formed into the manifold
combustion chambers with increased squish parts for
better combustion efficiency and its intake and exhaust

SOHC ENGINE MECANICAL 1B–3
DAEWOO M-150 BL2
parts are installed in the cross flow arrangement. The
rocker arm (i) operates in seesaw motion to close and
open the intake and exhaust valves (j) with camshaft by
turning the rocker arm shaft of each intake and exhaust
part.
ENGINE BLOCK
As the largest part of the engine components. the block
(l) has all the necessary parts attached to outer surface
of it.
On the inside surface of block, there are bore surfaces
by horning, which are cylinders, and on the periphery of
the cylinders, there are the passages to prevent the
over-heated and to lubricate the engine block.
CRANKSHAFT
The crankshaft (m) is to convert the rectilinear motion
into the rotation motion through the connecting rod (n)
which transmits the power generated by combustion.
On the one side of it, oil pump, crankshaft pulley and
timing belt pulley are attached, and oil seal housing and
flywheel are on the other side.
A special steel of high grade cast iron is used for the ma-
terial to stand the bending load and distortion. The mate-
rial of the main bearing (o) is aluminum alloy. The split
thrust bearings (p) are inserted in the journal bearing
part (No.3).
D102B004
CONNECTING ROD
The connecting rods (n) are made of forged steel, and
its section is typed “I” with its big end connected tocrankshaft (m) and its small end to piston pin to transmit
the power.
The big end is detachable, and its upper and lower parts
are fastened by bolting after the metal bearings (q) are
inserted.
PISTON, PISTON RING AND PISTON
PIN
Piston
The piston (r) is of the open skirt type and its crown is
exposed in the combustion chamber to generate power.
Its land and skirt parts are made of coat aluminum alloy
which is light and has excellent heat conductivity in order
to meet its continuous and high speed reciprocation
movement.
Piston Ring
It is composed of two compression rings (s) and one oil
ring (t) and installed between the grooves of the piston
to make the high speed reciprocating movement main-
taining a remarkable air tightness as well as cylinders. It
is a critical parts to affect the compression pressure, oil
consumption, compression, blow by pressure and en-
gine performance.
Piston Pin
The pin (u) is not fixed to the piston or connecting rod
and its both ends are assembled by the circlip (v) in the
full floating type. The pin is used to transmit the power
from the crown part of piston to connecting rod.
D102B005

SOHC ENGINE MECANICAL 1B–5
DAEWOO M-150 BL2
COMPONENT LOCATOR
CYLINDER HEAD
D12B4011
1 Oil Filler Cap
2 Cylinder Head Cover
3 Cylinder Head Cover (Euro III)
4 Distributor Case
5 Camshaft
6 Exhaust Rocker Arm7 Cylinder Head Gasket
8 Cylinder Head
9 Intake Rocker Arm
10 Exhaust Valve
11 Intake Valve

1B –6 SOHC ENGINE MECANICAL
DAEWOO M-150 BL2
ENGINE BLOCK
D21B0011
1 Oil Level Gauge Stick
2Piston
3 Connecting Rod
4 Engine Block
5 Oil Filter6 Flywheel
7 Crankshaft
8 Oil Pan
9 Oil Pump Strainer
10 Oil Pump Assembly