2003 DAEWOO MATIZ Electric window

GLASS AND MIRRORS 9L–7
DAEWOO M-150 BL2
D19E508A
9. Check for waterleaks by pouring water on the wind-
shield. If a leak is found, dry the windshield and fill
the area that leaks with adhesive. If the leak per-
sists, remove the windshield and repeat the entire
procedure.
10. Install the inside rearview mirror. Refer to “Inside
Rearview Mirror” in this section.
11. Install the cowl vent grille. Refer to Section 9R, Body
Front End.
D19E509
REAR WINDOW GLASS
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the rear window defogger electrical con-
nectors.
D19E510
3. Using the glass sealant remover J–24402, cut the
adhesive around the rear window glass.
D19E503
4. Remove the rear window glass from the vehicle.
5. Using a knife, remove the adhesive from the rear win-
dow glass.
6. Using a knife, remove the adhesive from the rear win-
dow frame.

9L –8 GLASS AND MIRRORS
DAEWOO M-150 BL2
D109E511
Installation Procedure
1. Apply tape to the new weatherstrip and the rear win-
dow to hold the weatherstrip in place.
2. Apply adhesive primer to the rear window frame and
the perimeter of the rear window.
D109E512
3. Apply glass adhesive to the rear window frame.
D19E513A
4. Install the rear window into the rear window frame.
5. Reposition the tape over the weatherstrip, the rear
window and the rear window frame to hold the rear
window in place.
6. Let the adhesive dry for 24 hours.
7. Remove the tape.
D19E514A
8. Check for waterleaks by pouring water on the rear
window. If a leak is found, dry the window and fill the
area that leaks with adhesive. If the leak persists,
remove the rear window and repeat the entire pro-
cedure.
9. Connect the rear window defogger electrical con-
nector.
10. Connect the negative battery cable.

GLASS AND MIRRORS 9L–9
DAEWOO M-150 BL2
D19E509
REAR WINDOW DEFOGGER GRID
LINE REPAIR
1. Disconnect the negative battery cable.
2. Disconnect the rear window defogger electrical con-
nector.
D19E515
3. Inspect the rear window defogger grid lines.
4. Use steel wool to buff the grid lines that are to be
repaired. Wipe the lines clean using a cloth damp-
ened with alcohol. Buff and clean about 6 mm (0.25
inch) beyond each side of the break in the grid line.
D19E516
5. Attach a grid line repair decal or two strips of tape
above and below the repair areas.

A repair decal or tape must be used in order to
control the width of the repair areas.

If a decal is used, the die–cut metered slot must
be the same width as the grid line.
6. Apply the grid repair material to the repair area using
a small wooden stick or a spatula. The grid repair
material should be at room temperature.
7. Carefully remove the decal or the tape.
D19E517
Notice: The grid line repair material must be cured with
heat. In order to avoid heat damage to the interior trim,
protect the trim near the repair area where heat will be
applied.
8. Heat the repair area for 1 to 2 minutes.
9. Hold the heat gun nozzle 25 mm (1 inch) from the
surface. A minimum temperature of 149C (300F)
is required.

DAEWOO M-150 BL2
SECTION 9P
DOORS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9P-2. . . . . . . . . . . . . . . . . .
Door Lock Striker 9P-2. . . . . . . . . . . . . . . . . . . . . . . . . .
Childproof Rear Door Lock 9P-2. . . . . . . . . . . . . . . . . .
Power Door Locks 9P-2. . . . . . . . . . . . . . . . . . . . . . . . .
Power Windows 9P-2. . . . . . . . . . . . . . . . . . . . . . . . . . .
Tailgate Strut 9P-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component Locator 9P-3. . . . . . . . . . . . . . . . . . . . . . . .
Front Door 9P-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Door 9P-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9P-7. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 9P-7. . . . . . . . . . . . . . . . . . . . . . . . . .
Front Door Glass Run 9P-7. . . . . . . . . . . . . . . . . . . . . .
Rear Door Glass Run 9P-8. . . . . . . . . . . . . . . . . . . . . .
Door Lock Striker 9P-9. . . . . . . . . . . . . . . . . . . . . . . . . .
Tailgate Lock Striker 9P-9. . . . . . . . . . . . . . . . . . . . . . .
Door Lock Striker Adjustment 9P-10. . . . . . . . . . . . . .
Tailgate Lock Striker Adjustment 9P-11. . . . . . . . . . . .
Front Door Lock 9P-13. . . . . . . . . . . . . . . . . . . . . . . . . .
Childproof Rear Door Lock 9P-14. . . . . . . . . . . . . . . . .
Central Door Lock Actuator 9P-16. . . . . . . . . . . . . . . .
Tailgate Lock 9P-16. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inside Door Handle 9P-17. . . . . . . . . . . . . . . . . . . . . . . Outside Front Door Handle 9P-17. . . . . . . . . . . . . . . .
Outside Rear Door Handle 9P-18. . . . . . . . . . . . . . . . .
Door Lock Cylinder 9P-18. . . . . . . . . . . . . . . . . . . . . . .
Manual Window Regulator 9P-19. . . . . . . . . . . . . . . . .
Power Front Window Regulator 9P-19. . . . . . . . . . . .
Front Door Assembly 9P-20. . . . . . . . . . . . . . . . . . . . .
Rear Door Assembly 9P-21. . . . . . . . . . . . . . . . . . . . . .
Tailgate 9P-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tailgate Lock Cylinder 9P-23. . . . . . . . . . . . . . . . . . . . .
Door Hinge 9P-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Door Hold Open Link 9P-24. . . . . . . . . . . . . . . . . . . . .
Inside Channel Weatherstrip (Standard) 9P-24. . . . .
Inside Channel Weatherstrip (Deluxe) 9P-25. . . . . . .
Door Outside Channel Weatherstrip 9P-25. . . . . . . . .
Door Weatherstrip 9P-26. . . . . . . . . . . . . . . . . . . . . . . .
Door Seal Trim 9P-27. . . . . . . . . . . . . . . . . . . . . . . . . . .
Door Opening Weatherstrip 9P-27. . . . . . . . . . . . . . . .
Manual Window Regulator Handle 9P-28. . . . . . . . . .
Tailgate Strut 9P-28. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 9P-30. . . . . . . . . .
Power Door Locks 9P-30. . . . . . . . . . . . . . . . . . . . . . . .
Power Windows (Front Only) 9P-34. . . . . . . . . . . . . . .

9P – 2 DOORS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
DOOR LOCK STRIKER
The front and the rear door lock strikers each consist of
a striker with two screws threaded into a floating cage
plate in the B-pillars and C-pillars. The door is secured in
the closed position when the door lock fork snaps over
and engages the striker.
CHILDPROOF REAR DOOR LOCK
The childproof rear door locks help prevent passengers,
especially children, from opening the rear doors of the
vehicle from the inside.
In order to activate these locks, move the levers of both
rear doors to the lock position. Then, close both doors.
Rear passengers will be unable to open the doors from
the inside of the vehicle.
In order to deactivate the childproof rear door lock, un-
lock the door from the inside of the vehicle and open the
door from the outside. Move the lever to the unlock posi-
tion. The rear door will now work normally.
POWER DOOR LOCKS
The power door locks use a solenoid that is contained in
each door lock assembly. The door locks are activatedby the actuator on the inside door handle or by the lock
cylinder on the driver door only. When the driver door is
locked or unlocked by the actuator or lock cylinder, all
doors are locked or unlocked accordingly.
POWER WINDOWS
The power windows are controlled by electrical switches
on the front door tirm and operated by a motor at each
window regulator. The windows are lowered by pressing
the switch and raised by pulling up on the switch. The
window will stop movement when the switch is released
or when the window is completely open or closed.
TAILGATE STRUT
This vehicle is equipped with the gas struts. The struts
support the tailgate suitably when opening the tailgate.
The strut contained the high pressure compressed gas.
Therefore, be careful not to take apart, puncture, apply
heat or fire bacause the strut may explode.

DOORS 9P–19
DAEWOO M-150 BL2
D109C600
Installation Procedure
1. Install the door lock cylinder with the clip.
2. Install the outside door handle. Refer to “Outside
Front Door Handle” in this section.
3. Connect the negative battery cable.
D109C601
MANUAL WINDOW REGULATOR
Removal Procedure
1. Remove the glass. Refer to Section 9L, Glass and
Mirrors.
2. Remove the window regulator.

Remove the screws (1).

Remove the regulator (2).
D109C602
Installation Procedure
1. Install the regulator with the screws.
2. Install the glass. Refer to Section 9L, Glass and Mir-
rors.
D109C603
POWER FRONT WINDOW
REGULATOR
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the glass. Refer to Section 9L, Glass and
Mirrors.
3. Remove the window regulator assembly.

Disconnect the window motor electrical connector
(1).

Remove the screws (2).

Remove the window regulator assembly (3).

9P –20 DOORS
DAEWOO M-150 BL2
D109C604
4. Remove the window motor from the window regula-
tor.

Remove the screws (1).

Remove the window regulator (2).
Caution: Be careful what you are doing when sepa-
rating the window motor and the window regulator.
You may be hurt.
D109C605
Installation Procedure
1. Install the window motor to the window regulator with
the screws.
2. Install the window regulator assembly with the screws.
3. Connect the window motor electrical connector.
4. Install the glass. Refer to Section 9L, Glass and Mir-
rors.
5. Connect the negative battery cable.
D109C606
FRONT DOOR ASSEMBLY
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the electrical connector under the instru-
ment panel.
Important: In case of the front passenger door, remove
the glove box in advance.
D109C607
3. Remove the fender. Refer to Section 9R, Body Front
End.
4. Remove the front door assembly.

Remove the door hinge bolts (1).

Remove the door hold open bolt (2).

Disconnect the body–to–door rubber grommet (3).

Remove the front door assembly (4).

DOORS 9P–23
DAEWOO M-150 BL2
D19C614A
Installation Procedure
Notice: Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use the correct
fastener to prevent premature corrosion.
1. Connect the body–to–tailgate rubber grommet.
2. With the aid of another technician, lightly secure the
tailgate with the bolts.
3. Adjust the tailgate for proper fit.
4. Install the tailgate strut. Refer to “Tailgate Strut” in this
section.
5. Connect the tailgate electrical connector.
6. Install the luggage compartment wheelhouse trim pan-
el. Refer to Section 9G, Interior Trim.
7. Connect the negative battery cable.
D209B113
TAILGATE LOCK CYLINDER
Removal Procedure
1. Disconnect the negative battery cable.
2. Open the tailgate.
3. Remove the rear window wiper motor assembly. Re-
fer to Section 9D, Wipers/Washer Systems.
4. Remove the tailgate lock cylinder.

Disconnect the tailgate lock rod (1).

Remove the nuts from the tailgate lock cylinder (2).

Remove the tailgate lock cylinder (3).
D209B114
Installation Procedure
1. Install the tailgate lock cylinder.
2. Install the rear window wiper motor assembly. Refer
to Section 9D, Wipers/Washer Systems.
3. Connect the negative battery cable.
D109C615
DOOR HINGE
Removal Procedure
1. With the aid of another technician, remove the door
hinge.

Remove the hinge–to–body bolts (1).

Remove the hinge–to–door bolts (2).

Remove the door hinge (3).