2003 CADILLAC CTS buttons

2-75
HomeLink
Transmitter
(If Equipped)
A. HomeLink
Transmitter
Buttons
B. Travel Note
Recorder Buttons
(If Equipped)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS
-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference, including interference
that may cause undesired operation of the device.Changes and modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
Programming the HomeLink Transmitter
Do not use the HomeLink Transmitter with any garage
door opener that does not have the ªstop and reverseº
feature. This includes any garage door opener model
manufactured before April 1, 1982.
Be sure that people and objects are clear of the garage
door you are programming.
It is recommended that a new battery be installed in
your hand
-held transmitter for quicker and more
accurate transmission of the radio frequency.
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. Decide which one of the three channels (one of the
HomeLink buttons) you want to program.
2. Press and hold the desired button on HomeLink
through Step 3.

2-76
3. When the HomeLink indicator light begins to blink
slowly (this may take up to 30 seconds), hold the
hand
-held transmitter about 1 to 3 inches (3 to 8 cm)
away from HomeLink and then press and hold the
transmit button on the hand
-held transmitter.
Continue to hold both buttons until the indicator
light on HomeLink begins to flash rapidly (this may
take up to 90 seconds).
If you have trouble programming HomeLink, make sure
that you have followed the directions exactly as
described and that the battery in the hand
-held
transmitter is not weak. If you still cannot program it,
move the hand
-held transmitter to the left or right or
forward or backward or flip it upside down. HomeLink
may not work with older garage door openers that do
not meet current Federal Consumer Safety Standards.
If you cannot program the transmitter after repeated
attempts, refer to ªTraining a Garage Door Opener with
a `Rolling Code' Featureº next in this section or contact
the manufacturer of HomeLink at 1
-800-355-3515, or
on the internet at www.homelink.com.
Be sure to keep the original hand
-held transmitter in
case you need to erase and reprogram HomeLink.
Training a Garage Door Opener with a
ªRolling Codeº Feature (If Equipped)
If you have not previously programmed the hand-held
transmitter to HomeLink, see ªProgramming the
HomeLink Transmitterº listed previously. If you have
completed this programming already, you now need to
train the garage door opener motor head unit to
recognize HomeLink.
1. Find the ªLearnº or ªSmartº button on the garage
door opener motor head unit. The exact location and
color will vary by garage door opener brand. If you
have difficulty finding the Learn or Smart button,
refer to your garage door opener owner's manual or
contact the manufacturer of HomeLink at
1
-800-355-3515, or on the internet at
www.homelink.com.
Because of the steps involved, it may be helpful to
have another person assist in programming the
transmitter.

2-77
2. Press the Learn or Smart button on the garage
door opener motor head unit. An indicator light will
begin to flash when the motor head unit enters the
training mode.
Following this step, you have 30 seconds to
start Step 3.
3. Return to HomeLink in your vehicle and firmly
press and release the programmed HomeLink button
three times.
The rolling
-code garage door opener should now
recognize HomeLink. You may either use HomeLink or
the hand
-held transmitter to open the garage door.
If after following these instructions, you still have
problems training the garage door opener, contact the
manufacturer of HomeLink at 1
-800-355-3515, or on
the internet at www.homelink.com.
Canadian Programming
Canadian Owners: During programming, the hand-held
transmitter may automatically stop transmitting after
two seconds. In this case, you should press and hold
the HomeLink button (see Steps 2 and 3 under
ªProgramming the HomeLink Transmitterº) while you
press and re
-press (cycle) your hand-held transmitter
every two seconds until HomeLink is trained.
Operating the HomeLink Transmitter
Press and hold the appropriate button on HomeLink for
at least half of a second. The indicator light will come
on while the signal is being transmitted.
Erasing Channels
To erase all three programmed channels, hold down the
two outside buttons until the indicator light begins to
flash (approximately 20 seconds). Release both buttons.

2-78
Resetting Defaults
To reset HomeLink to default settings, hold down the
two outside buttons until the indicator light begins to
flash (approximately 20 seconds). Continue to hold both
buttons until the HomeLink indicator light turns off and
then release both buttons.
Accessories
Accessories for the HomeLink Transmitter are available
from the manufacturer of the unit. If you would like
additional information, please contact the manufacturer
of HomeLink at 1
-800-355-3515, or on the internet
at www.homelink.com.
Travel Note Recorder (If Equipped)
The HomeLink transmitter module may also have a
travel note recorder that allows you to record short
messages for later review. You can record approximately
80 messages or four minutes of continuous recorded
information, whichever comes first.
A. HomeLink
Transmitter
Buttons
B. Travel Note
Recorder Buttons
The buttons that operate this feature are located on the
driver's side sun visor.

2-79

(Record): To record a message, press this button and
begin speaking. Press the button again to stop recording.
If you prefer, you can press and hold this button while
you record a message. The unit will begin recording
when you press the button and stop recording when you
release the button.
While a message is being recorded, the red light on the
travel note recorder will be lit. The light will go out
when recording has stopped.
(Play): Press this button to play back a recorded
message.
To listen to all the recorded messages, press and hold the
button for at least one second.
To skip a message, press the play button while a
message is playing. This will advance the recorder to the
next recorded message and begin playing it.
The green light on the unit will be lit while the messages
are playing.
(Delete): Press this button to delete recorded
messages.
To delete an individual message, press the delete button
while a message is playing or within five seconds after a
message has ended.
To delete all stored messages on the travel note recorder,
press the record and play buttons at the same time.
If you exceed the space limit, an error tone will sound
when you try to record another message, the light on the
unit will come on, and the message will not be recorded.
To remedy this, delete all unnecessary messages to free
some space for new messages.
If your vehicle has the optional Navigation System,
there is a memo recorder built into the system. See
ªVoice Memoº in the Index of the Navigation
Supplement for more information.

2-81
The main components of the instrument panel are the following:
A. Air Outlets
B. Turn Signal/Multifunction Lever
C. Reconfigurable Steering Wheel Controls
D. Instrument Panel Cluster
E. Cruise Control Buttons
F. Audio Mute Button (Base Radio) or Voice
Recognition Button (Navigation System)
G. Audio Volume Knob and Source Button
H. Windshield Wiper LeverI. Storage Compartment or Ashtray (Option)
J. Hazard Warning Flasher Button
K. Transmission Shift Lever
L. Accessory Power Outlet or Cigarette
Lighter (Option)
M. Climate Control System
N. Audio/Navigation System (Option)
O. Glove Box

2-131
Navigation System
1. Turn the ignition to ON without the engine running.
Make sure an automatic transmission is in PARK (P)
or a manual transmission has the parking brake set.
2. Turn on the Navigation/audio system by pressing the
PWR/VOL knob located to the lower left of the
display once.
3. Access the DIC main menu by pressing the MAIN
button located to the lower left of the display.
4. Press the multi
-function button next to Feat Prog to
access the Feature Programming menu.
5. Press the TUNE/SEL knob to turn on the
Personalization features. An X will appear in the box
to the left when Personalization is turned on.
Personalization Features
The following choices are available for programming
using both the Base audio and Navigation systems
unless otherwise indicated.
Personalization Name
This feature allows you to type in a name that will
appear on the DIC display whenever the corresponding
remote keyless entry transmitter is used or one of the
buttons on the driver's door armrest (1 or 2) is pressed.
If a customized name is not programmed, the system
will show Driver 1 or Driver 2 to correspond with the
numbers on the back of the remote keyless entry
transmitters.
To program a name, use one of the following
procedures:

3-12

SCAN: Press the SCAN button to enter scan mode.
SCAN will appear on the display. Press the up arrow to
scan to the next station. The radio will go to a station,
play for 5 seconds, then go on to the next station.
Press this button again to stop scanning.
To scan preset stations, press and hold SCAN for more
than two seconds until you hear a beep and PSCAN
appears on the display. The radio will go to the first
preset station stored on your pushbuttons, play for
5 seconds, then go on to the next preset station.
Press SCAN again to stop scanning presets.
The radio will scan only to stations that are in the
selected band and only to those with a strong signal.LOCAL/DISTANCE Selection: With this feature you
can set the radio to search for local stations or stations
that are further away for a larger selection. To set this
feature to LOCAL or DISTANCE, perform the
following steps:
1. Press the TUNE/SEL knob to enter the main menu.
2. Turn the TUNE/SEL knob until SEEK LOCAL or
SEEK DISTANCE appears on the display.
3. Press the TUNE/SEL knob to select either LOCAL
or DISTANCE.
4. Press the BACK button to exit the display. To return
to the original display repeatedly press the BACK
button or wait for the display to time out.
To search for stations, press the SEEK up or down
arrows. If the system is set to LOCAL, SEEK will
appear in the display. If the system is set to DISTANCE,
D
-SEEK will appear in the display. The radio will seek
to stations with a strong signal only.