2003 ASTON MARTIN DB AR1 Q ECU

F - Owner Maintenance
1-F-7
Engine Oil Level Check
When checking engine oil level, the car should be on level ground. If the
engine has been running immediately prior to the check, wait several
minutes after stopping the engine for the oil to drain back into the sump. The
dipstick (1) (which should be wiped clean before checking the oil level) is
located on the left-hand side of the engine. The oil level should be
maintained at the 'Max' dipstick mark.
Approximately one litre is required to bring the level from Min to Max. The
recommended engine oil should be added through the oil filler (3). Do not
overfill. Replace the filler cap securely.
WARNING: Running the engine with insufficient oil can cause serious damage.
To avoid personal injury and before working in or near the engine compartment,
switch off the engine and let it cool. Engine components are hot and may cause
severe burns. See also the warnings given in SERVICING PRECAUTIONS.

F - Owner Maintenance
1-F-11
Brake Fluid Reservoir
The brake fluid reservoir (5) is fitted to the driver's side of the engine
compartment on top of the brake master cylinder assembly.
Before removing the cap, clean the cap and the surrounding area thoroughly
to prevent ingress of dirt and foreign matter. Top up to the indicated level
on the reservoir with the recommended brake fluid (see 'Specifications') and
refit the cap securely.
Brake fluid will absorb water vapour and must be replaced every two years
in order to maintain the efficiency of the hydraulic system.
WARNINGS: Do not drive the vehicle if the brake fluid level is low. Use only new
DOT4 brake fluid from air tight containers.
Avoid touching the sides of the engine when working in the engine compartment.
The exhaust system will be hot if the engine has recently been run.
Caution: Take care that hydraulic fluid does not contact the paint work during the
topping up operation. Serious paint work damage can result. If a spillage does occur,
immediately flush the hydraulic fluid from the paint work with clean, fresh water and
then wipe with a clean damp cloth.

F - Owner Maintenance
1-F-14
Tyre Pressures
In the interest of safety and tyre life it is important that correct tyre pressures
are carefully maintained (See 'Specifications').
Road holding, steering and braking are especially vulnerable to incorrect
tyre pressures.
Pressures increase slightly when tyres are hot and, for an accurate reading,
pressures should be checked when the tyres are cold.
After checking the pressures ensure that the valve caps are securely replaced
to provide an additional air seal and to prevent the ingress of dirt.
Running-In New Tyres
When new tyres have been fitted, speed should be limited, particularly
during the first 80 km (50 miles) or so of driving. Fast cornering, hard braking,
and harsh acceleration should also be avoided during this period.
Tyre Service
Tyres should be examined at regular intervals for wear and damage. Stones
or other objects which have become lodged in the tyre treads should be
carefully removed.
When new tyres are required, it is advisable to consult an Aston Martin
dealer who will be able to supply tyres to the correct specification.

F - Owner Maintenance
1-F-22
Jacking and Wheel Changing
WARNINGS:
The front road wheels must be in the straight ahead position before removal. The
front tyre will catch on the wheel arch during removal if not in the "straight
ahead" position.
Check that the temporarily repaired tyre is inflated to the specified pressure.
Never exceed 50 km/h (30 mph) when a temporarily repaired wheel is fitted.
Ensure that no persons are in the vehicle before jacking commences.
Ensure that the handbrake (parking brake) is set and that the car is in 'Park' (Auto)
or 1st Gear (Manual).
Ensure that the vehicle is parked on firm and level ground to ensure a secure base
for the jack.
Do not run the engine while the car is on the jack and never let anyone work
under the car whilst it is on the jack.
Spare Wheel Access (where fitted)
On vehicles with the space saver spare
wheel, the spare wheel is stored in a
well in the boot floor.
Lift out the boot floor and toolkit.
Remove the spare wheel retaining screw
and lift out the spare wheel.

F - Owner Maintenance
1-F-23
Jacking and Wheel Changing
1. Place the vehicle on firm and level ground and secure the handbrake.
Place the chock from the toolkit under the wheel diagonally opposite to
the one to be removed. If parked on an incline, chock the 'downhill' side
of the wheel.
2. Remove the locking wheel nut
cap from the special nut using the
extractor tube from the toolkit.
Assemble the wheel nut wrench.
3. Using the wheel nut wrench from the tool kit, slightly loosen the four
normal wheel nuts in turn so that the nuts may be removed easily when
the wheel is raised from the ground.
4. Using the special socket from the toolkit, slightly loosen the fifth special
wheelnut.

F - Owner Maintenance
1-F-24
5. Using the handwheel (A) on the jack screwshaft, raise the jack until the
jack top plate (B) fits to the jacking point stud under the sill at the affected
wheel. Ensure that the jack baseplate is squarely seated on solid ground.
Note: In the following step, the jack handle extension (D) must be used to prevent
damage to the vehicle paintwork as the jack handle (C) is rotated.
6. Ensure the safety of any persons in the vicinity and the security of the
wheel chock. Raise the vehicle as necessary using the jack ratchet handle
(C) and extension (D) to lift the deflated wheel clear of the ground.
Remove the wheel nuts and remove the deflated wheel.
7. Mount the spare wheel on the hub. Reverse the jack ratchet handle on
the extension and partially tighten the wheel nuts.
8. Lower the vehicle to the ground. Tighten the wheel nuts alternately.
Remove the wheel chock.
9. Repack the tools into their location in the boot. Place the defective wheel
into the bag provided and place on the rear seats.
10. When the spare wheel is correctly fitted and secured, drive conservatively
(80 km/h (50 mph) maximum) and have the wheel nuts torque tightened
to 88-102 Nm (65-75 lbs/ft) at the earliest opportunity.
WARNINGS:
Follow the wheel label warnings. Failure to comply can be dangerous. Drive
cautiously and refit a serviceable standard wheel and tyre as soon as possible.
Never fit more than one temporary spare wheel at a time.
Check that the temporary spare tyre is inflated to the specified pressure.
Never exceed 80 km/h (50 mph) when the spare wheel is fitted.

F - Owner Maintenance
1-F-27 The DB AR1 may then be winched onto a transporter or towed to a safe
location using a rope, provided that the following precautions are observed:
Transporting
If the vehicle is to be transported on a trailer or flat bed transporter, the
handbrake must be applied and the wheels chocked. Vehicles fitted with
Touchtronic transmission must have the gear selector lever moved to N or
D but NEVER in P. The parking lock may be damaged if the vehicle is
transported with the gear selector lever in P.
Four tie-down brackets are provided, two on each axle. These are NOT
suitable for solid bar towing.
Front Axle Tie-Down Rear Axle Tie Down
Vehicles with Defective Touchtronic Transmission
The vehicle must be carried on a transporter or towed with the rear wheels
clear of the ground (see suspended towing) or towed with the propeller shaft
disconnected at the final drive input flange. If the propeller shaft is
disconnected, it must be firmly secured away from the final drive flange.

F - Owner Maintenance
1-F-28
Suspended Towing
Do NOT tow with sling-type equipment since damage to the bodywork may
result.
Take care when using 'spectacle frame' type towing equipment that the
towing device is well clear of the front or rear apron. Body damage may
occur if the vehicles pass over uneven road surfaces.
Adhere to Towing Regulations
In certain countries the registration number of the towing vehicle and an ON
TOW sign or warning triangle must be displayed in a prominent position at
the rear of the vehicle being towed.
Front Suspended Tow
Caution: To prevent body damage ensure an adequate clearance is
maintained between the car body and (1) the ground and (2) the 'spectacle
frame' of the towing vehicle while your car is being towed.
1. Remove the ignition key from the ignition.
2. Vehicles with manual transmission: Place the gear lever in neutral.
Vehicles with automatic transmission:
Disconnect the propeller shaft at the final drive input flange.
Ensure that the propeller shaft is firmly secured away from the final drive
input flange.