2003 Acura MDX clock

Clean the hood latch assembly with a
mild cleaner, then lubricate it with a
multipurpose grease. Lubricate all
the moving parts (as shown),
including the pivot. Follow the time
and distance recommendations in
the Maintenance Schedule. If you
are not sure how to clean and grease
the latch, contact your Acura dealer.Clean off any dirt and oil that have
collected around the ignition coils.
The spark plugs in your vehicle
should be replaced according to the
time and distance recommendations
in the maintenance schedule.
Loosen the two holding clips by
turning the heads one-quarter turn
counterclockwise with a f lat-tipped
screwdriver. Remove the cover by
pulling it straight up.
Disconnect the cable from the
coveronthefrontcylinderbank
by pulling the cable out of the
holder.
1. 2.
3.
CONT INUED
Hood L atch
Spark Plugs
Hood L at ch, Spark Plugs
Maint enance
Replacement
323
LATCH ASSEMBLY
HOLDING CLIP

Torque the spark plug. (If you do
not have a torque wrench, tighten
the spark plug two-thirds of a turn
af ter it contacts the cylinder head.)
Tightening torque:Install the ignition coil. Reinstall
the hexagon socket head cap bolt.
Push the wire connector onto the
ignition coil. Make sure it locks in
place.
Repeat this procedure f or the
other f ive spark plugs.
Reinstall the cover on the front
cylinder bank while putting its
mounting clip in the hole on the
passenger’s side. Secure the cover
by turning the heads of the two
holding clips one-quarter turn
clockwise with a f lat-tipped
screwdriver.NGK:
DENSO:
8. 9.
11.
12.
10. Specif ications:
Spark Plugs
Maint enance325
13 lbf·ft (18 N·m , 1.8 kgf·m) SKJ16DR-M11 IZFR5K-11
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.

Open the hood.
Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustment of the headlights should
be perf ormed by a Acura technician
or other qualif ied mechanic.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Your vehicle has halogen headlight
bulbs, two on each side. When
replacing a bulb, handle it by its steel
base and protect the glass from
contactwithyourskinorhard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
Remove the electrical connector
fromthebulbbysqueezingthe
connector to unlock the tab, then
slide the connector of f the bulb.
1. 2.
3.
CONT INUED
Replacing a Headlight Bulb
Headlight A iming
Lights
Maint enance341
BULB
CONNECTORHalogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.

Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
To remove the f ront turn signal
bulb, push it in slightly and turn it
counterclockwise. To remove the
side marker bulb, pull it straight
out of its socket.Testthelightstomakesurethe
new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Install the new bulb into the
socket.
Push the electrical connector onto
the new bulb.
Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
Turn on the headlights to test the
new bulb. 1.
2.
3.
4.
5.
4.
5.
6. Replacing Front Turn Signal/
Parking and Side Marker Light
Bulbs
Lights
Maint enance342
TAB

Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Your car uses halogen f og light
bulbs. See page f or inf ormation
on replacing a halogen bulb.
Remove the electrical connector
fromthebulbbysqueezingthe
connector to unlock the tab, then
slide the connector of f the bulb.
Push the electrical connector onto
the new bulb.
Use a wrench to loosen the light
assembly’s mounting bolt.
Remove the light assembly f rom
the bumper.
1.
2.
3.
4.
5.
341
CONT INUED
ReplacingaFogLightBulb
Lights
Maint enance343
BOLT
CONNECTOR

Turn on the headlights to test the
new bulb. Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
Put the light assembly into the
bumper. Tighten the mounting
bolt.Remove the socket by turning it
one-quarter turn counterclockwise.
Open the tailgate. Use a
screwdriver protected with a cloth
to pry open the two covers.
Remove the two screws and
remove the rear light assembly
f rom the rear pillar.
Determine which of the f our bulbs
is burned out: brake/taillight, turn
signal/hazard lights, side marker
light, or back-up light. Remove the burned out bulb. To
remove the brake/taillight, back-
up or side marker light bulb, pull
the bulb straight out of its socket.
To remove the turn signal/hazard
light bulb, push it in and turn it
counterclockwise until it unlocks.
1.
2.
3.
4.
8. 6.
7.
5.
Replacing Rear Bulbs
Lights
Maint enance344

Put the socket back into the light
assembly and turn it clockwise to
lock it in place. Test the light to make sure the
new bulb is working. Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Install the new bulb into the
socket.
Push the socket into the light
assembly and turn it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Install the rear light assembly in
the body.Tighten the two screws.
Snap the covers back into position.
Remove the light assembly cover
by prying caref ully with a cloth-
covered screwdriver in the
notches along the top edge.Then
pivot the cover out and down.
Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.Place the cover back into the light
assembly. Push it up until it locks
in place.
1. 4.
5.
6.
2. 3.
6.
7.
8.
9. Replacing a High-mount Brake
Light Bulb
Lights
Maint enance345

Open the tailgate.Take the tools out of the storage
compartment.
Turn the jack’s end bracket
counterclockwise to loosen it, then
remove the jack.
Thetoolsandjackarebehinda
cover in the cargo area on the
driver’s side. Remove the cover by
pushing the top of the cover. The spare tire is stored
underneath the rear cargo area.
Remove the plastic cover on the
cargo area lining to access the
shaft for the spare tire hoist.
3.
4.
5.
6.7.
Changing a Flat T ire
T aking Care of t he Unexpect ed362
COVER
COVER