2003 Acura MDX clock

µ´
CONT INUED
All models of MDX have a trip
computer. The f ollowing pages
explain the trip computer on the
model without the navigation system.
To operate the trip computer on the
model with the navigation system,
ref er to the navigation manual.
The Trip Computer displays the
f ollowing inf ormation. The ignition
switch must be in Accessory or ON.Clock
Direction of travel
Trip Computer
Comf ort and Convenience Feat ures
(Without Navigation System)
219
INSTANTANEOUS
FUEL MILEAGE
CLOCK
BUTTON
TRIP
BUTTON
RESET
BUTTON
DISPLAY BRIGHTNESS
CONTROL /CALIBRATE BUTTON
/ZONE BUTTONRESET, SET BUTTONCOMPASS
OUTSIDE
TEMPERATURE

The temperature sensor is located
in the f ront bumper. Theref ore,
the temperature reading can be
affected by heat reflection from
the road surf ace, engine heat, and
the exhaust f rom the surrounding
traf f ic. Because of these
conditions, it may take a while f or
the temperature to read correctly.
Instantaneous f uel mileage
The Range, or estimated distance
you can travel on the fuel
remaining in the tank. This
distance is estimated from the fuel
economy you have gotten over the
last several miles, so it will vary
with changes in speed, traf f ic, etc. Outside temperature
Trip Computer
Comf ort and Convenience Feat ures220
ELAPSED TIMERANGEINSTANTANEOUS FUEL MILEAGE
CLOCK COMPASS
AVERAGE FUEL
ECONOMY TRIP METER
OUTSIDE TEMPERATURE

To set the clock:Push the CLOCK button. The
hours digits will start blinking. If
you want to only set the minutes,
go to step 4. To change the hours to a lower
number, press and hold the
MODE button. To change the
hours to a higher number, press
andholdtheA/Cbutton.
To set the minutes, press the
CLOCK button again. The
minutes digits will start blinking.
When the hours reach the desired
number, release the button. Use the MODE or A/C button to
set the minutes to the desired
number.
Press the CLOCK button again.
The clock will return to its normal
display.
1.
2.
3.4.
5.
6.
Setting the Clock
Trip Computer
Comf ort and Convenience Feat ures222

µµ
You can also quickly set the time to
the nearest hour. Press the CLOCK
button, then press the RESET button.
If the displayed time is before the
half hour, it will reset back to the
previous hour. If the displayed time
is af ter the half hour, it will reset
f orward to the next hour.
For example:
1:06 will reset to 1:00
1:52 will reset to 2:00
The compass shows your direction
of travel. It indicates eight directions.
Compass operation can be af f ected
by driving near power lines or
stations, across bridges, through
tunnels, over railroad crossings, past
large vehicles, or driving near large
objects that can cause a magnetic
disturbance.
It can also be af f ected by accessories
such as antennas and roof racks that
are mounted by magnets.The compass may need to be
manually calibrated af ter exposure to
a strong magnetic field. If the
compassseemstobecontinually
showing the wrong direction and is
not self -calibrating, do the f ollowing.
NOTE: You should do this procedure
in an open area, away from buildings,
power lines, and other vehicles.
The compass is self -calibrating. If
you see ‘‘ ’’ in the direction
display and ‘‘Calibrate’’ is blinking,
the compass is self -calibrating.
CONT INUED
Trip Computer
Compass Operation
Compass Calibration
Comf ort and Convenience Feat ures223

µµ
Press and hold the CLOCK and
TRIP buttons until the display
changes (about 1 second).
Press the Calibrate (MODE)
button.
Press the Set (FAN) button.
‘‘Calibrate’’ will start blinking, and
the direction display will change to
‘‘ ’’.
1.
2.
Trip Computer
Comf ort and Convenience Feat ures224

µµ
Drivethevehicleslowlyintwo
complete circles. In most areas, there is a variation
between magnetic north and true
north. Zone selection is required so
the compass can compensate f or this
variation. To check and select the
zone set into the compass, do the
f ollowing.
Press and hold the CLOCK and
TRIP buttons until the display
changes (about 1 second).
When the display goes f rom
‘‘ ’’ to an actual heading, the
unit is calibrated.
Press the CLOCK, TRIP, or
RESET button to complete the
calibration and return the display
to normal. 1.
CONT INUED
Trip Computer
Comf ort and Convenience Feat ures
Compass Zone Select ion
225

If the zone is incorrect, press and
hold the MODE button to get the
number to count down, or the A/C
button to get the number to count
up. If the zone is correct, continue
to step 5.
Press the Set (FAN) button to set
the zone selection.
Press the CLOCK, TRIP or
RESET button to exit the zone
selection and return display to
normal.
Press the Zone (A/C) button. The
zone the compass is currently set
to is displayed.
Find the zone f or your area on the
map.
2.
3. 4.
5.
6.
Trip Computer
Comf ort and Convenience Feat ures226

Make sure the engine and radiator
are cool.
Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
Remove the radiator cap by
pushing down and turning
counterclockwise.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Pourthecoolantslowlyand
caref ully so you do not spill. Clean
up any spills immediately. Spilled
coolant could damage components
in the engine compartment.
Put the radiator cap back on.
Tighten it f ully.
3. 4.
5. 6.
1.
2.
Cooling Syst em
Maint enance312
RESERVE TANK