2003 Acura MDX buttons

If the seat belt touches or crosses
your neck, or if it crosses your arm
instead of your shoulder, you need to
adjust the seat belt anchor height.To adjust the height of a f ront seat
belt anchor, squeeze the two release
buttons and slide the anchor up or
down as needed (it has f our
positions).
If necessary, pull up on the shoulder
belt again to remove any slack from
the shoulder belt, then check that
the belt rests across the center of
your chest and over your shoulder.
This spreads the f orces of a crash
over the strongest bones in your
upper body.
Driver and Passenger Saf ety
Protecting Adults
16
RELEASE
BUTTON
Improperly positioning the seat
belts can cause serious injury
or death in a crash.
Make sure all seat belts are
properly positioned before
driving.

Turn of f the engine.
Press and hold the select and reset
buttons on the instrument panel,
then turn the ignition switch ON
(II).
Hold the buttons for
approximately ten seconds until
the indicator resets.
1.
2.
3.
Gauges
Inst rument s and Cont rols77
SELECT BUTTON
RESET BUTTON

Theremotetransmitterswillalso
activate the Driving Position
Memory System (see page ).
When you open the driver’s door
after unlocking it with the remote
transmitter, you will hear a beep.
The driver’s seat and outside mirrors
move to the positions stored in that
memory location. You will hear two
beeps when the movement iscomplete.
If the seat and mirrors are already in
the proper positions, you will hear
three beeps when you open the door.
The driving position memory
activated (Memory 1, Memory 2) is
shownonthebackof each
transmitter. Make sure you store
your desired driving position in the
memory that is activated by the
transmitter you normally carry.
To turn it back on, repeat this
procedure. The LED will come on
f or one second to indicate the
f eature has been turned on. You can turn the driving position
memory activation off and on. To
turn it of f , press and hold the LOCK
and UNLOCK buttons at the same
time f or about one second. The LED
in the remote transmitter will blink
twice. Then release the buttons.
118
On Touring Model
Recalling a Memorized Driving
Position
Keys and Locks
Inst rument s and Cont rols98
With Memory 1 With Memory 2

Use the ignition key to release the
seat belt from the detachable
anchor.
To create more cargo space, you can
fold the third seat forward.
To fold the third seat:
Remove the head restraints by
pushing the release buttons and
pulling the restraints out. Store the head restraints in the
storage compartment. Make sure
the head restraints are f ace up
(storing them face down can
damage the compartment or the
headrests), then insert the shaf ts
into the holes in the sides of the
storage compartment.
1. 2.
3.
CONT INUED
Folding the T hird Seat
Seats
Inst rument s and Cont rols107
RELEASE BUTTON

Turn the ignition switch ON (II).
You cannot add a new driving
position in the memory unless the
ignition switch is ON (II). You can
recall a memorized position with
the ignition switch in any position.
Seat and outside mirror positions, f or
two dif f erent drivers or driving
conditions,canbestoredinseparate
memories. You select a memorized
position by pushing the appropriate
button or using the appropriate
remote transmitter (Memory 1 or
Memory 2). Store a driving position as explained
in this section only when the vehicle
is parked.
Adjust the seat to a comfortable
position (see page ). Press and release the MEMO
buttononthecontrolpanel.You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator light in the
memory button will come on. The
current positions of the driver’s
seat and outside mirrors are now
stored.
Your Acura has a memory f eature
f or the driver’s seat and outside
mirror positions.
Adjust the outside mirrors f or best
visibility (see page ).3.
1.
2.
116
101
Touring Model
St oring a Driving Posit ion in Memory
Driving Posit ion Memory Syst em
Inst rument s and Cont rols118
MEMO BUTTON

Doing any of the f ollowing af ter
pressing the MEMO button will
cancel the storing procedure.Not pressing a memory button
within 5 seconds.
You can select memorized positions
as f ollows.Make sure the parking brake is set
and the shif t lever is in Park.
Readjusting the seat position.
Readjusting the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button. Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.The system will move the seat and
outside mirrors to the memorized
positions. The indicator light in the
selected memory button will f lash
during movement. When the
adjustments are complete, you will
hear two beeps and the indicator
light will remain on.
All stored driving positions will be
lost if your vehicle’s battery goes
dead or is disconnected. 1.
2.
CONT INUED
Select ing a Memorized Posit ion
Driving Posit ion Memory Syst em
Inst rument s and Cont rols119
MEMORY BUTTONS

CONT INUED
When you turn the A/C of f , the
system cannot regulate the inside
temperature if you set it below the
outside temperature. With the A/C
on, use the temperature buttons to
adjust the temperature of the air
flow to a comfortable setting. Pressing the A/C button or touching
the A/C icon turns the air
conditioningonandoff.Youwillsee
A/C ON or A/C OFF displayed. You can manually select various
f unctions of the Climate Control
system when it is in FULL AUTO.
All other f eatures remain auto-
matically controlled. Some of these
f unctions appear in the Trip
Computer/Navigation System
display. With the Navigation System,
press the A/C-Trip button next to
the display to show these functions.
Climat e Cont rol Syst em
Comf ort and Convenience Feat ures
Semi-automatic Operation
A ir Condit ioning (A /C) But t ons
137
RECIRCULATION BUTTONTEMPERATURE BUTTONS
(without Navigation System) (with Navigation System)
AIR CONDITIONING (A/C) BUTTON/ICON

This button controls the source of
the air going into the system. When
the indicator above this button is lit,
air f rom the vehicle’s interior is sent
through the system again (Recircula-
tion mode). When the indicator is off,
air is brought in f rom outside the
vehicle (Fresh Air mode).
You can, f or example, manually put
the system in recirculation mode
when driving through an area of
smoke or f umes.
You can manually select the f an
speed with the fan speed button/fan
speed icon. Pressing the button or
touching the icon repeatedly makes
the fan run faster. The fan speed is
shownbybarsinthedisplay.If the
f an is at its highest speed, pressing
the button or touching the icon again
takes it to its lowest speed.
Climat e Cont rol Syst em
Comf ort and Convenience Feat ures
Recirculat ion But t onFan Speed Icon/Fan Speed But t on
138
RECIRCULATION BUTTON TEMPERATURE BUTTONS
FAN SPEED BUTTON
MODE BUTTON MODE ICON FAN SPEED ICONS