Page 65 of 86
6-34
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU04189
Replacing the headlight bulb
Headlight bulb, replacing
This motorcycle is equipped with a
quartz bulb headlight. If the headlight
bulb burns out, replace it as follows.
1. Remove the headlight unit by
removing the screws.2. Disconnect the headlight cou-
pler, and then remove the bulb
cover.
1
2
1
1. Headlight unit
2. Screw (×2)1. Headlight coupler
EC000103
cCDo not use a fuse of a higher
amperage rating than recommend-
ed to avoid causing extensive
damage to the electrical system
and possibly a fire.3. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 64
Page 66 of 86
6-35
PERIODIC MAINTENANCE AND MINOR REPAIR
6 3. Unhook the headlight bulb hold-
er, and then remove the defec-
tive bulb.
EW000119
wHeadlight bulbs get very hot.
Therefore, keep flammable prod-
ucts away from a lit headlight bulb,
and do not touch the bulb until it
has cooled down.4. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
EC000105
cCDo not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the
bulb, and the bulb life will be
adversely affected. Thoroughly
clean off any dirt and fingerprints
on the headlight bulb using a cloth
moistened with alcohol or thinner.5. Install the headlight bulb cover,
and then connect the coupler.
1
a
1. Headlight bulb holder a. Do not touch this area.
1
1. Bulb cover
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 65
Page 67 of 86
6-36
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU03218
Replacing a turn signal light
bulb1. Remove the turn signal lens by
removing the screws.2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
cCDo not overtighten the screws,
otherwise the lens may break.
2
1
1
1. Lens
2. Screw (×2)1. Bulb
6. Install the headlight unit by
installing the screws.
7. Have a Yamaha dealer adjust
the headlight beam if necessary.
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 66
Page 68 of 86
6-37
PERIODIC MAINTENANCE AND MINOR REPAIR
6 2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
cCDo not overtighten the screws,
otherwise the lens may break.
EAU01579
Supporting the motorcycle
Supporting the motorcycle
Since this model is not equipped with
a centerstand, follow these precau-
tions when removing the front and
rear wheel or performing other main-
tenance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed
under the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcy-
cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing
a jack under the frame in front of
the rear wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand.
1
1. Bulb
EAU01623
Replacing the tail/brake light
bulb
Tail/brake light bulb, replacing
1. Remove the tail/brake light lens
by removing the screws.
2
1
1. Lens
2 Screw (×2)
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 67
Page 69 of 86
6-38
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU03239
Front wheel
Front wheel
To remove the front wheel
Removing
EW000122
w8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so that there is no danger
of it falling over.1. Disconnect the speedometer
cable from the front wheel.2. Loosen the front wheel axle
pinch bolt, then the wheel axle.
3. Lift the front wheel off the ground
according to the procedure on
page 6-37.
4. Pull the wheel axle out, and then
remove the wheel.
ECA00048
cCDo not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
1
1 2
1. Speedometer cable 1. Front wheel axle pinch bolt
2. Wheel axle
To service the rear wheel
Raise the rear wheel off the ground
by using a motorcycle stand or, if a
motorcycle stand is not available, by
placing a jack either under each side
of the frame in front of the rear wheel
or under each side of the swingarm.
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 68
Page 70 of 86
6-39
PERIODIC MAINTENANCE AND MINOR REPAIR
6
NOTE:
Make sure that there is enough
space between the brake pads
before inserting the brake disc and
that the slot in the speedometer gear
unit fits over the retainer on the fork
leg.3. Insert the wheel axle.
4. Lower the front wheel so that it is
on the ground.5. Tighten the wheel axle to the
specified torque.
6. Tighten the front wheel axle
pinch bolt to the specified torque.
7. Push down hard on the handle-
bar several times to check for
proper fork operation.
8. Connect the speedometer cable.
1
1. Retainer
EAU04423
To install the front wheel
1. Install the speedometer gear unit
into the wheel hub so that the
projections mesh with the slots.
2. Lift the wheel up between the
fork legs.
1
1. Speedometer gear unit
Tightening torque:
Wheel axle:
59 Nm (5.9 m0kgf)Tightening torque:
Front wheel axle pinch bolt:
20 Nm (2.0 m0kgf)
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 69
Page 71 of 86
6-40
PERIODIC MAINTENANCE AND MINOR REPAIR
62. Lift the rear wheel off the ground
according to the procedure on
page 6-37.
3. Disconnect the brake torque rod
from the brake shoe plate by
removing the nut and the bolt.
4. Remove the brake pedal free
play adjusting nut, and then dis-
connect the brake rod at the
brake camshaft lever.5. Loosen the locknut and the drive
chain adjusting nut on both ends
of the swingarm.
6. Remove the axle nut, and then
pull the wheel axle out.
7. Push the wheel forward, and
then remove the drive chain from
the rear sprocket.
NOTE:
The drive chain does not need to be
disassembled in order to remove and
install the wheel.8. Remove the wheel.
2
14
3
5
1
32
1. Brake torque rod nut
2. Brake torque rod
3. Brake pedal free play adjusting nut
4. Brake rod
5. Brake camshaft lever1. Locknut
2. Drive chain adjusting nut
3. Wheel axle
EAU03189
Rear wheel
Wheel (rear)
To remove the rear wheel
Removing
EW000122
w8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so that there is no danger
of it falling over.1. Loosen the axle nut and the
brake torque rod nut at the brake
shoe plate.
1
1. Axle nut
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 70
Page 72 of 86
6-41
PERIODIC MAINTENANCE AND MINOR REPAIR
6 6. Tighten the axle nut to the speci-
fied torque.
7. Adjust the brake pedal position
and free play. (See page 6-20 for
brake pedal position and free
play adjustment procedures.)
EW000103
wAfter adjusting the brake pedal
free play, check the operation of
the brake light.
EAU01008
Troubleshooting
Troubleshooting
Although Yamaha motorcycles
receive a thorough inspection before
shipment from the factory, trouble
may occur during operation. Any
problem in the fuel, compression, or
ignition systems, for example, can
cause poor starting and loss of
power.
The following troubleshooting chart
represents a quick and easy proce-
dure for checking these vital systems
yourself. However, should your
motorcycle require any repair, take it
to a Yamaha dealer, whose skilled
technicians have the necessary tools,
experience, and know-how to service
the motorcycle properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life
and can lead to expensive repair
bills. Tightening torque:
Axle nut:
104 Nm (10.4 m0kgf)
EAU03190
To install the rear wheel
Installing
1. Insert the wheel axle from the
left-hand side, and then install
the drive chain onto the rear
sprocket.
2. Install the axle nut, and then
lower the rear wheel so that it is
on the ground.
3. Install the brake rod onto the
brake camshaft lever, and then
install the brake pedal free play
adjusting nut onto the brake rod.
4. Connect the brake torque rod to
the brake shoe plate by installing
the bolt and the nut, and then
tighten the bolt to the specified
torque.
5. Adjust the drive chain slack.
(See page 6-25 for drive chain
slack adjustment procedures.) Tightening torque:
Brake torque rod bolt:
23 Nm (2.3 m0kgf)
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 71
