2002 SUZUKI GRAND VITARA 550

YH4
GRAND
VITARA
3B1-18 POWER STEERING (P / S) SYSTEM
ªAº
1
1
1. Mark
1. Tie-rod lock washer
(A)
INSTALLATION
1) Install new tie-rod lock washer and tie-rod to rack.
2) Tighten tie-rod ball nut to specified torque.
Tightening Torque
(a): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
3) Bend lock washer 2 place at the flat part of tie-rod ball nut.
4) Apply grease to ªAº indicated in figure.
5) Position boot properly in grooves of gear case and tie-rod.
Check to ensure that boot is free from twist and dent.
6) Fasten boot with new clamp and clip securely.
Special Tool
(A): 09943-55010
7) Install tie-rod end lock nut and tie-rod end to tie-rod.
Position lock nut to marking made in removal.
NOTE:
When tie-rod was replaced, measure length ªAº on re-
moved tie-rod and use it on new replacement tie-rod so as
to position lock nut properly.
8) Install steering gear case. Refer to ªPOWER STEERING GEAR
BOX ASSEMBLY INSTALLATIONº in this section.

YH4
GRAND
VITARA
3B1-26 POWER STEERING (P / S) SYSTEM
09915-77420
Oil pressure gauge
attachment and hose set09915-77410
Oil pressure gauge09943-55010
Boot clamp plier
TIGHTENING TORQUE SPECIFICATION
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Gear box mounting bolts555.540.0
Gear box cylinder pipe flare nuts292.921.0
Gear box low pressure pipe union bolt404.029.0
Gear box high pressure pipe union bolt353.525.5
Tie-rod end lock nut656.547.0
G16 Type engine555.540.0
Pump bracket boltJ20 Type engine252.518.5
H25 Type engine454.532.5
Pump union bolt606.043.5
Oil pump mount bolts252.518.5
Pipe clamp bolt / Reservoir bracket bolt111.18.0
Steering shaft joint bolt252.518.0
High pressure flare nuts404.029.0
Pump cover bolts232.317.0
Plug606.043.5
Pressure switch (Terminal)282.820
Suction connector bolt101.07.5
Tie-rod end nut484.835.0
Tie-rod (for canvas top LH model only)858.561.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUPER GREASE (A)
(99000-25010)
Oil seal lip of P / S pump pulley shaft
Power steering fluidAn equivalent of DEXRON
-III or
DEXRON
-II

To fill P / S fluid reservoir

Parts lubrication when installing
SPECIAL TOOL

YH4
GRAND
VITARA
Hole to hole distance
ªa ± gº : 276 mm (10.87 in.)
ªa ± kº : 1000 mm (39.37 in.)
ªb ± b'º : 1302 mm (51.26 in.)
ªb ± gº : 730 mm (28.74 in.)
ªc ± c'º : 668 mm (26.30 in.)
ªc ± eº : 414 mm (16.30 in.)
ªc ± gº : 406 mm (15.98 in.)
ªc ± jº : 1029 mm (40.51 in.)
ªc ± kº : 1000 mm (39.37 in.)
ªd ± d'º : 1302 mm (51.26 in.)
ªd ± eº : 189 mm (7.44 in.)
ªd ± c'º : 1016 mm (40.00 in.)
ªd ± gº : 672 mm (26.46 in.)
ªd ± kº : 968 mm (38.11 in.)
ªe ± e'º : 1456 mm (57.32 in.)ªf ± f'º : 1550 mm (61.02 in.)
ªf ± hº : 299 mm (11.77 in.)
ªf ± jº : 811 mm (31.93 in.)
ªg ± kº : 854 mm (33.62 in.)
ªh ± h'º : 1339 mm (52.72 in.)
ªh ± j'º : 1504 mm (59.21 in.)
ªh ± jº : 677 mm (26.65 in.)
ªh ± kº : 927 mm (36.50 in.)
ªi ± i'º : 1344 mm (52.91 in.)
ªi ± jº : 391 mm (15.39 in.)
ªi ± kº : 760 mm (29.92 in.)
ªj ± j'º : 1348 mm (53.07 in.)
ªj ± kº : 676 mm (26.61 in.)
ªl ± jº : 961 mm (37.83 in.)
ªl ± kº : 1018 mm (40.08 in.)
a. Front bumper installation clip hole
b (b'). Front bumper installation hole
c (c'). Headlight installation hole
d (d'). Headlight installation resin nut hole
e (e'). Headlight installation hole
f (f'). Front fender installation hole
g. Center member installation hole
h (h'). Fender installation reference hole
i (i'). Fender installation hole
j (j'). Fender installation reference hole
k. Garnish installation clip hole
l. Mounting installation hole
9-26 BODY SERVICE
BODY DIMENSIONS
4 door model, 2 door model