2002 SUZUKI GRAND VITARA hazard switch

YH4
GRAND
VITARA
5-10 BRAKES
BRAKE PEDAL PLAY CHECK
Pedal play should be within specification. If out of specification,
check brake light switch for proper installation position and adjust
if necessary.
Also check pedal shaft bolt and master cylinder pin installation for
looseness and replace if defective.
Pedal play ªdº: 1 ± 8 mm (0.04 ± 0.32 in.)
BRAKE FLUID LEVEL CHECK
Be sure to use particular brake fluid either as indicated on reservoir
cap of that vehicle or recommended in owner's manual which
comes along with that vehicle.
Use of any other fluid is strictly prohibited.
Fluid level should be between MIN and MAX lines marked on reser-
voir.
When warning light lights sometimes during driving, replenish fluid
to MAX line.
When fluid decreases quickly, inspect brake system for leakage.
Correct leaky points and then refill to specified level.
CAUTION:
Do not use shock absorber fluid or any other fluid which
contains mineral oil. Do not use a container which has been
used for mineral oil or a container which is wet from water.
Mineral oil will cause swelling and distortion of rubber parts
in hydraulic brake system and water mixed into brake fluid
will lower fluid boiling point. Keep all fluid containers
capped to prevent contamination.
BRAKE HOSE AND PIPE CHECK
The brake hose assembly should be checked for road hazard dam-
age, for cracks and chafing of the outer cover, for leaks and blisters.
A light and mirror may be needed for an adequate inspection. If any
of the above conditions are observed on the brake hose, it is neces-
sary to replace it.
Inspect the pipe for damage, cracks, dents and corrosion. If any de-
fect is found, replace it.
MASTER CYLINDER CHECK
Check for a cracked master cylinder casting or brake fluid around
the master cylinder. Leaks are indicated only if there is at least a
drop of fluid. A damp condition is not abnormal.

YH4
GRAND
VITARA
8B
LIGHTING SYSTEM 8B-1
SECTION 8B
LIGHTING SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
GENERAL DESCRIPTION8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight with Leveling System (If Equipped) 8B- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearance, Tail and License Plate Lights 8B- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back-up Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
8B-4 LIGHTING SYSTEM
DIAGNOSIS
NOTE:
Fuse name (ª º) in the table below is shown on the fuse box cover (Hard Top Model) or the junction box
(Canvas Top Model).
HEADLIGHTS
TroublePossible causeCorrection
Only one light does not
light
Bulb blown

Headlight L or R fuse blown

Socket, wiring or grounding faultyReplace bulb
Replace fuse to check for short
Repair
Headlights do not light
Headlight L and R fuses blown

Lighting and dimmer switch faulty

Defective light relay

Wiring or grounding faultyReplace fuses to check for short
Replace switches
Replace light relay
Repair
Only one beam (ªHiº or
ªLoº) does not light
Bulb blown

Lighting or dimmer switch faultyReplace bulb
Replace switch
HEADLIGHTS WITH LEVELING SYSTEM (IF EQUIPPED)
TroublePossible causeCorrection
Both headlights do not
move
ªTURN / BACKº fuse blown (Hard Top Model)
ªTRNº fuse blown (Canvas Top Model)

Leveling switch faulty

Supply voltage too lowReplace fuse to check for short
Replace switch
Recharge or replace battery
One of headlights (either
Right or Left) does not
move
Socket, wiring or grounding faulty

Actuator faulty

Vehicle body around headlight deformed

Headlight ass'y itself deformedRepair
Replace actuator
Repair body
Replace headlight ass'y
TURN SIGNAL AND HAZARD WARNING LIGHTS
TroublePossible causeCorrection
Flash rate high or one side
only flashes
Incorrect bulb

One of light bulbs burnt out

Turn signal / hazard warning relay faulty

Open circuit or high resistance existing
Replace bulb
Replace
Replace relay
Repair
Oen circuit or high resistance existing
between turn signal / hazard warning
switch and lights on one side

Wiring or grounding faulty
Re air
Repair
No flashing
ªTURN / BACKº and / or ªHAZARDº fuse(s)
blown (Hard Top Model)
ªTRNº and / or ªHAZº fuse(s) blown
(Canvas Top Model)

Open circuit or high resistance existing
between battery and switch

Turn signal / hazard relay faulty

Combination switch or hazard switch faulty

Wiring or grounding faultyReplace fuse(s) to check for
short
Check bulb and check circuit
Replace relay
Replace switch
Repair
Flash rate low
Supply voltage too low

Turn signal / hazard relay faultyCheck charging system
Replace relay

YH4
GRAND
VITARA
1. Meter cluster
2. Hazard switch
Terminal
Wire ColorSwitch Position
LH steering vehicle shown
LIGHTING SYSTEM 8B-9
TURN SIGNAL AND HAZARD WARNING
LIGHTS
TURN SIGNAL SWITCH (IN COMBINATION SWITCH)
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace switch.
TLTBTR
G/RGG/Y
L
N
R
REMOVAL AND INSTALLATION
Refer to Section 3C COMBINATION SWITCH for vehicle without air
bag system and Section 3C1 CONTACT COIL AND COMBINA-
TION SWITCH ASSEMBLY for vehicle with air bag system.
HAZARD SWITCH
REMOVAL
1) Remove meter cluster.
2) Pull hazard switch out of instrument panel.
3) Disconnect coupler from hazard switch.
4) Remove hazard switch.
INSTALLATION
Reverse removal procedure.
INSPECTION
Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace siwtch.

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-7
POWER DOOR LOCK AND KEYLESS ENTRY SYSTEM (IF KEYLESS ENTRY IS
EQUIPPED)
TroublePossible causeCorrection

All power doors are not
locked / unlocked by
both driver side door key
switch and power door
lock switch. But all
power doors are locked /
unlocked by keyless
entry transmitter

All power doors are not
locked / unlocked by
driver side door key
switch, power door lock
switch and keyless entry
transmitter

When power doors are
locked / unlocked by
keyless entry
transmitter, hazard
warning lights do not
flash
ªDOOR LOCKº fuse blown

Power door lock and keyless entry system
faultyReplace fuse to check for short
Refer to SYSTEM INSPECTION
of POWER DOOR LOCK AND
KEYLESS ENTRY SYSTEM
(IF KEYLESS ENTRY IS
EQUIPPED) in this section
All power doors are not
locked / unlocked by only
power door lock switch
Power door lock switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
driver side door key
switch
Driver side door key switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
keyless entry transmitter
Code registration error

Transmitter battery dead

Transmitter faulty

Power door lock and keyless entry system
faultyRegister code
Replace battery
Replace transmitter
Refer to SYSTEM INSPECTION
of POWER DOOR LOCK AND
KEYLESS ENTRY SYSTEM
(IF KEYLESS ENTRY IS
EQUIPPED) in this section
Although any door is
opened within 30 seconds
after power door(s)
unlocked by keyless entry
transmitter, all power
doors are locked again
automatically
Door switch faulty

Wiring harness connected to door switch
brakesReplace switch
Repair
Only one power door is not
locked / unlocked
Wiring or coupler faulty

Actuator (door lock motor) faultyRepair
Replace actuator
Operation distance of
keyless entry is unstable
Transmitter battery dead

Transmitter faultyReplace battery
Replace transmitter

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-23
POWER DOOR LOCK AND KEYLESS ENTRY SYSTEM (IF KEYLESS ENTRY IS
EQUIPPED)
SYSTEM INSPECTION
STEPACTIONYESNO
1Check power door lock operation referring to its
INSPECTION in this section.
Is this operation OK?Go to Step 2.Go to Step 3.
2Check keyless entry operation referring to its
INSPECTION in this section.
Is this operation OK?Go to Step 4.Go to Step 6.
3Check keyless entry operation referring to its
INSPECTION in this section.
Is this operation OK?Go to Step 5.Go to Step 7.
4Check hazard warning lights operation referring to
its INSPECTION in this section.
Is this operation OK?This system is OK.Go to Step 10.
5Check door lock key and power door lock switch
circuit referring to its INSPECTION in this section.
Is this circuit OK?Replace controller and
recheck.
And go to Step 4.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
And go to Step 4.
6Check ignition switch and door switch circuit
referring to its INSPECTION in this section.
Is this circuit OK?Replace controller and
recheck.
And go to Step 4.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
And go to Step 4.
7Check power door lock actuator circuit referring to
its INSPECTION in this section.
Is this circuit OK?Go to Step 8.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
If OK, go to Step 4.
If not OK, go to next
Step 8.
8Check power supply and grounding circuit
referring to its INSPECTION in this section.
Is this circuit OK?Go to Step 9.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
If OK, go to Step 4.
If not OK, go to next
Step 9.
91) Check door lock key and power door lock
switch circuit referring to its INSPECTION in
this section.
2) Check ignition switch and door switch circuit
referring to its INSPECTION in this section.
Are these circuits OK?Replace controller and
recheck.
And go to Step 4.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
And go to Step 4.

YH4
GRAND
VITARA
8D-24 WINDOWS, MIRRORS, SECURITY AND LOCKS
STEPACTIONYESNO
10Check that hazard warning lights flash with hazard
switch ON.
Is check result OK?Go to Step 11.Refer to ªTurn Signal
and Hazard Warning
Lightsº in DIAGNOSIS
and repair.
And go to Step 4.
11Check door knob switch and turn signal relay
circuit referring to its INSPECTION in this section.
Is this circuit OK?Replace controller and
recheck.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
POWER DOOR LOCK OPERATION
INSPECTION
1) With the driver side door key turned LOCK, check all power
doors are locked.
2) With the driver side door key turned UNLOCK, check only the
driver side power door is unlocked.
Turn the driver side door key to UNLOCK again within 5 se-
conds, check all power doors are unlocked.
If check result of Step 1) and Step 2) is satisfactory, this operation
is OK.
KEYLESS ENTRY OPERATION
INSPECTION
1) With the IG switch OFF and all doors closed, push LOCK button
on transmitter. Check all power doors are locked.
2) Push UNLOCK button on transmitter. Check only driver side
power door is unlocked.
3) Push UNLOCK button on transmitter again within 5 seconds.
Check all power doors are unlocked.
But if any door is not opened within 30 seconds after power
door(s) unlocked, all power doors are locked again automatical-
ly.
If check result of Step 1) to Step 3) is satisfactory, this operation is
OK.
HAZARD WARNING LIGHTS OPERATION
INSPECTION
1) Check that hazard warning lights flash one time when power
doors are locked by pushing LOCK button on transmitter.
2) Check that hazard warning lights flash two times when power
door(s) is (are) unlocked by pushing UNLOCK button on trans-
mitter.
If check result of Step 1) and Step 2) is satisfactory, this operation
is OK.