2002 SUZUKI GRAND VITARA Fluid

YH4
GRAND
VITARA
5-6 BRAKES
ConditionPossible CauseCorrection
Brake warning light
turns on after
engine start
Parking brake applied.

Insufficient amount of brake fluid.

Brake fluid leaking from brake line.

Brake warning light circuit faulty.

Malfunctioning EBD system, if equipped
with ABS.Release parking brake and check
that brake warning light turns off.
Add brake fluid.
Investigate leaky point, correct it and
add brake fluid.
Repair circuit.
Check system referring to
ªDIAGNOSISº of ABS section.
Brake warning light
turns on when
brake is applied
Brake fluid leaking from brake line.

Insufficient amount of brake fluid.Investigate leaky point, correct it and
add brake fluid.
Add brake fluid.
Brake warning light
fails to turn on
even when parking
brake is applied
Bulb burnt out.

Brake warning light circuit open.Replace bulb.
Repair circuit.
ABS warning light
does not turn on
for 2 sec. after
ignition switch has
turned ON
Bulb burnt out.

ABS warning light circuit open, if equipped
with ABS. (including check relay)Replace bulb.
Check system referring to
ªDIAGNOSISº of ABS section.
ABS warning light
remains on after
ignition switch has
turned on for 2 sec.
Malfunctioning ABS, if equipped with ABS.Check system referring to
ªDIAGNOSISº of ABS section.

YH4
GRAND
VITARA
1. 4-way joint / 2-way joint
2. Master cylinder
3. LSPV
4. Right brake caliper
5. Left brake caliper
6. Right wheel cylinder
7. Left wheel cylinder
8. ABS actuator

: Air bleeding point [A]: Without ABS
[B]: With ABS
1. Plug cap2. Vinyl tube (See-through tube)
3. Container
[A]
[B]
BRAKES 5-7
CHECK AND ADJUSTMENT
BLEEDING BRAKES
CAUTION:
Brake fluid is extremely damaging to paint. If fluid should
accidentally touch painted surface, immediately wipe
fluid from paint and clean painted surface.
NOTE:
For vehicle equipped with ABS, make sure that ignition switch
turns off.
Be sure to bleed air of brake system according to following proce-
dure when its oil hydraulic circuit has been disconnected.
Hydraulic lines of brake system consists of two separate lines, one
for front wheel brakes and the other for rear wheel brakes.
Air bleeding is necessary at right and left front wheel brakes, left
rear wheel brake and LSPV (if equipped without ABS), i.e. 4 places
(3 places for vehicle with ABS) in all.
1) Fill master cylinder reservoir with brake fluid and keep at least
one-half full of fluid during bleeding operation.
2) Remove bleeder plug cap.
Attach a vinyl tube to bleeder plug of wheel cylinder, and insert
the other end into container.
3) Depress brake pedal several times, and then while holding it de-
pressed, loosen bleeder plug about one-third to one half turn.

YH4
GRAND
VITARA
5-8 BRAKES
4) When fluid pressure in the cylinder is almost depleted, retigh-
ten bleeder plug.
5) Repeat this operation until there are no more air bubbles in hy-
draulic line.
6) When bubbles stop, depress and hold brake pedal and tighten
bleeder plug.
For tightening torque specification of air bleeder plug, re-
fer to ªTIGHTENING TORQUE SPECIFICATIONº in this
section.
7) Then attach bleeder plug cap.
8) After completing bleeding operation, apply fluid pressure to
pipe line and check for leakage.
9) Replenish fluid into reservoir up to specified level.
10) Check brake pedal for ªsponginessº. If found spongy, repeat
entire procedure of bleeding.

YH4
GRAND
VITARA
5-10 BRAKES
BRAKE PEDAL PLAY CHECK
Pedal play should be within specification. If out of specification,
check brake light switch for proper installation position and adjust
if necessary.
Also check pedal shaft bolt and master cylinder pin installation for
looseness and replace if defective.
Pedal play ªdº: 1 ± 8 mm (0.04 ± 0.32 in.)
BRAKE FLUID LEVEL CHECK
Be sure to use particular brake fluid either as indicated on reservoir
cap of that vehicle or recommended in owner's manual which
comes along with that vehicle.
Use of any other fluid is strictly prohibited.
Fluid level should be between MIN and MAX lines marked on reser-
voir.
When warning light lights sometimes during driving, replenish fluid
to MAX line.
When fluid decreases quickly, inspect brake system for leakage.
Correct leaky points and then refill to specified level.
CAUTION:
Do not use shock absorber fluid or any other fluid which
contains mineral oil. Do not use a container which has been
used for mineral oil or a container which is wet from water.
Mineral oil will cause swelling and distortion of rubber parts
in hydraulic brake system and water mixed into brake fluid
will lower fluid boiling point. Keep all fluid containers
capped to prevent contamination.
BRAKE HOSE AND PIPE CHECK
The brake hose assembly should be checked for road hazard dam-
age, for cracks and chafing of the outer cover, for leaks and blisters.
A light and mirror may be needed for an adequate inspection. If any
of the above conditions are observed on the brake hose, it is neces-
sary to replace it.
Inspect the pipe for damage, cracks, dents and corrosion. If any de-
fect is found, replace it.
MASTER CYLINDER CHECK
Check for a cracked master cylinder casting or brake fluid around
the master cylinder. Leaks are indicated only if there is at least a
drop of fluid. A damp condition is not abnormal.

YH4
GRAND
VITARA
1. Air bleeder plug
2. Weight
3. Attachment2
ªLº
BRAKES 5-13
FLUSHING BRAKE HYDRAULIC SYSTEM
It is recommended that entire hydraulic system be thoroughly
flushed with clean brake fluid whenever new parts are installed in
hydraulic system.
Periodical change of brake fluid is also recommended.
FLUID PRESSURE TEST(if equipped with
LSPV)
Test procedure for LSPV assembly is as follows.
Before testing, confirm the following.

Fuel tank is filled with fuel fully.

Vehicle is equipped with spare tire, tools, jack and jack handle.
1) Stop vehicle on level floor and place approximately about
200 kg (441 lbs) weight on rear housing so that rear axle weight
800 kg (1764 lb).
Rear axle weight ªLº: 800 kg (1764 lb)
2) Install special tool to front and rear brake.
NOTE:
Special tool should be connected to breather of front (driv-
er's side brake) and rear brakes.
Special Tool
Front brake
(A): 09956-02310
(B): 09952-46510 (Attachment for vehicle with SUMITOMO
ELECTRIC brake caliper)
(C): 55473-82030 (Air bleeder plug supplied as a spare part)
Rear brake
(A): 09956-02310
(B): 09952-36310 (Attachment for thread diameter 7 mm of
bleeder plug) or
09952-46510 (Attachment for thread diameter 8 mm of
bleeder plug)
(C): 55473-82030 (Air bleeder plug supplied as a spare part)
NOTE:

Special tool (B) is used instead of thread diameter 10 mm
attachment of special tool (A).
So remove the attachment from (A) and install (B) as
shown in figure.

For vehicle with TOKICO brake caliper, use the attach-
ment included in special tool (A).

For identification of brake caliper type, refer to GENERAL
DESCRIPTION in SECTION 5B.

YH4
GRAND
VITARA
3. LSPV stay
1. Master cylinder
2. Disconnect brake pipe1. LSPV lever
2. LSPV spring
3, ªAº 2
1
2(a)
ªaº
ªbº
5-14 BRAKES
3) Depress brake pedal gradually till fluid pressure of front brake
becomes as specified below and check corresponding pressure
of rear brake then. It should be within specification given below.
Front brake
Rear brake
8,000 kPa
80 kg / cm2
3 Door
6,000 ± 7,300 kPa
60 ± 73 kg / cm2
853 ± 1,038 psi80 kg / cm2
1,138 psi5 Door
4,500 ± 7,300 kPa
45 ± 73 kg / cm2
640 ± 1,038 psi
As done above, apply 100 kg / cm2 pressure to front brake and
check that rear brake pressure then is within specification as giv-
en below.
Front brake
Rear brake
10,000 kPa
100 kg / cm2
3 Door
6,500 ± 8,000 kPa
65 ± 80 kg / cm2
924 ± 1,138 psi100 kg / cm2
1,422 psi5 Door
5,000 ± 8,000 kPa
50 ± 80 kg / cm2
711 ± 1,138 psi
4) If rear brake pressure is not within specification, adjust it by
changing stay ªAº position as follows.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

If rear brake pressure is higher than specification, move stay
ªAº to direction ªaº and if it is lower, to direction ªbº.

Repeat steps 3) and 4) until rear brake pressure is within spec-
ification.

After adjustment, be sure to torque bolt to specification.
5) Disconnect brake pipe (connecting between master cylinder
secondary side and 4-way joint) from master cylinder.
Tighten plug (special tool) to master cylinder.
Depress brake pedal. If rear brake pressure is 95 ± 100 kg / cm
2
when front brake pressure is 100 kg / cm2, it means that front fail-
safe system functions properly.
Front brake
Rear brake
10000 kPa
100 kg / cm2
1422 psi
9500 ± 10000 kPa
95 ± 100 kg / cm2
1350 ± 1422 psi
Special Tool
(A): 09956-02210

YH4
GRAND
VITARA
GOOD
NO GOOD
BRAKES 5-15
6) Upon completion of fluid pressure test, bleed brake system and
perform brake test.
BOOSTER OPERATION CHECK
There are two ways to perform this inspection, with and without a
tester. Ordinarily, it is possible to roughly determine its condition
without using a tester.
NOTE:
For this check, make sure that no air is in hydraulic line.
INSPECTION WITHOUT TESTER
Check Air Tightness
1) Start engine.
2) Stop engine after running for 1 to 2 minutes.
3) Depress brake pedal several times with the same load as in ordi-
nary braking and observe pedal travel. If pedal goes down deep
the first time but its travel decreases as it is depressed the se-
cond and more times, air tightness is obtained.
4) If pedal travel doesn't change, air tightness isn't obtained.
NOTE:
If defective, inspect vacuum lines and sealing parts, and re-
place any faulty part.
When this has been done, repeat the entire test.

YH4
GRAND
VITARA
BRAKES 5-17
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Brake pipe 2-way (or 4-way) joint bolt232.317.0
Brake pipe flare nut161.611.5
Front caliperM88.00.86.0
Brake bleederplug
Front cali erM108.50.856.5Brake bleeder lugWheel cylinder7.50.755.5
LSPV7.50.755.5
LSPV mounting bolt
LSPV stay bolt232.317.0
LSPV spring nut
Wheel nut10010.072.5
Stop light switch lock nut7.50.755.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.