2002 SUBARU IMPREZA WRX warning

Instruments and controls
3-15
– CONTINUED –
Light control switch
The light switch operates only when the ignition
switch is in the “ON” position.
WARNING
To prevent battery discharge resulting from
accidentally leaving your lights on when your
vehicle is parked, the light switch operatesonly when the ignition switch is in the “ON”
position. In any other position, the vehicle ’s
lights will be out.
If you park your vehicle on a roadside at night,use the hazard warning flasher to alert theother drivers.
Headlights
HB2007BA
To turn on the headlights, turn the knob on the end
of the turn signal lever.
first position
Parking lights, instrument panel illumination, tail
lights and license plate light are on.
second position
Headlights, parking lights, instrument panel illumina-
tion, tail lights, and license plate light are on.

Instruments and controls
3-17
– CONTINUED –
Daytime running light system
WARNING
The tail lights, parking lights, and side marker
lights are not turned on by the daytime run-ning light system. The light switch must al- ways be turned to the “a ” position when it
is dark outside.
The low beam headlights will automatically come on
at reduced brightness when the engine has started,
under the following conditions: The parking brake is fully released.
The light switch is in the “OFF” or “p ” position.
The automatic transmission selector lever is set at
other than the “P” position. Turn signal lever
HB2015BC
1) Right turn
2) Left turn
3) Lane change for right
4) Lane change for left
To activate the right turn signal, push the turn signal
lever up. To activate the left turn signal, push the
turn signal lever down. When the turn is finished, the
lever will return automatically. If the lever does not
return after cornering, return the lever to the neutralposition by hand.
To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane
change. The turn signal indicator lights will flash in

Instruments and controls
3-20
Wiper and washer
WARNING
In freezing weather, do not use the windshield
washer until the windshield is sufficiently
warmed by the defroster.Otherwise the washer fluid can freeze on the
windshield, blocking your view.
CAUTION
Do not operate the washer continuously for
more than ten seconds, or when the washer
fluid tank is empty. This may cause overheat-
ing of the washer motor. Check the washer
fluid level frequently, such as at fuel stops. Do not operate the wipers when the wind-
shield or rear window is dry. This may scratchthe glass, damage the wiper blades and causethe wiper motor to burn out. Before operating
the wiper on a dry windshield or rear window,
always use the windshield washer. In freezing weather, be sure that the wiper
blades are not frozen to the windshield or rear window before switching on the wipers.Attempting to operate the wiper with the
blades frozen to the window glass could
cause not only the wiper blades to be dam-aged but also the wiper motor to burn out. Ifthe wiper blade is frozen to the window glass,
be sure to operate the defroster, windshield wiper deicer (if equipped) or rear window
defogger before turning on the wiper.
If the wipers stop during operation because
of ice or some other obstruction on the win-
dow, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turnthe ignition switch to the “LOCK” position and
clean the window glass to allow proper wiperoperation. Use clean water if windshield washer fluid is
unavailable. In areas where water freezes in
winter, use SUBARU Windshield Washer Fluidor the equivalent. (See the “Windshield wash-
er fluid ” section in chapter 11.)
Also, when driving the vehicle when there are
freezing temperatures, use non-freezing type wiper blades. Do not clean the wiper blades with gasoline
or a solvent, such as paint thinner or benzene.

Instruments and controls
3-28
4. Releasing the button for 3 seconds will exit the zone setting mode. Outside mirrors
HS0065
Convex mirror (passenger side)
WARNING
Objects look smaller in a convex mirror and
farther away than when viewed in a flat mirror. Do not use the convex mirror to judge the dis-tance of vehicles behind you when changinglanes. Use the inside mirror (or glance back-wards) to determine the actual size and dis- tance of objects that you view in convex mir-
ror.
Remote control mirror switch
The remote control mirrors operate only when the
ignition switch is in the “ON” or “ACC” position.
HG3012BB
1) Selection switch
2) Direction control switch
1. Press either end of the selection switch, “L” for
the left, “R” for the right.
2. Move the direction control switch in the direction
you want to move the mirror.
3. Return the selection switch to the neutral position
to prevent unintentional operation.

Instruments and controls
3-30
Tilt steering wheel
HB4002BA
1. Adjust the seat position. Refer to the “Front seat ”
section (chapter 1).
2. Pull the tilt lock lever down.
3. Move the steering wheel to the desired level.
4. Push the lever up to lock the steering wheel inplace.
5. Make sure that the steering wheel is securely locked by moving it up and down.
WARNING
Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle
control and result in personal injury.

Climate control
4-5
– CONTINUED –
Air conditioner button (if equipped)
HB5010BB
1) Push
The air conditioner operates only when the engine is running. Push the air conditioner button while the fan is in op-
eration to turn on the air conditioner. The indicator
light will come on.
Push it again to turn off the air conditioner. Air inlet selection lever
: Interior air is recirculated inside the vehicle.: Outside air is drawn into the passenger
compartment.
WARNING
Continued operation in the position may
fog up the windows. Switch to the posi-
tion as soon as the outside dusty condition clears.
Heater operation
Defrosting or defogging the windshield
HG4023AA
To direct warm air to the windshield and front door windows:
1. Set the air inlet selection lever to the “
”
position.

Climate control
4-8
Ventilation
HG4027AA
To force outside air through the instrument panel outlets:
1. Set the air inlet selection lever to the “
”
position.
2. Set the air flow control dial to the “
” position.
3. Set the temperature control dial all the way left.
4. Set the fan speed control dial to the desiredspeed.
When driving on a dusty road, set the air inlet con-
trol lever to the “ON” position.
WARNING
Continued operation in the “” position
may fog up the windows. Switch to the “
” position as soon as the outside dusty
condition clears.
Air conditioner operation
Cooling or dehumidifying
HG4028BB
1) ON position
For cooling and dehumidification of the passenger
compartment, air flows through the instrument paneloutlets:

Interior equipment
6-10
WARNING
To avoid being burned, never grasp the lighter
by the end with the heating element. Doing so
could result in injury and could also damagethe heating element.
CAUTION
Do not hold the lighter pushed in, because it will overheat.Ashtray
Fully close the ashtray after using it to help reduce
residual smoke.
HG6006CB
1) Push 2) Pull
To open the ashtray, pull the lid out.
To remove the ashtray for cleaning, open it and pull it out while pushing the inner plate down.
CAUTION
Do not use ashtrays as waste receptacles or
leave a lighted cigarette in an ashtray. This could cause a fire.