2002 PEUGEOT 807 reset

26
PETROL / DIESEL CONTROL MODULE
1 Dipped beam headlamps indi
cator light.
2 Main beam headlamps indicator
light.
3 Lefthand direction indicator.
4 Service indicator, oil level
indicator, automatic gearbox
indicator* and total distance
recorder.
5 Front fog lamps indicator light. 6
Righthand direction indicator.
7 Dynamic stability control
ASR/ESP indicator light.
8 Rear fog lamps indicator light.
9 ABS system warning light.
10 Engine diagnostics warning
light.
11 Cruise control indicator light.
12 Lighting rheostat. 13
Handbrake, brake fluid level
and electronic brake force
distribution warning light.
14 Engine oil pressure warning
light.
15 Central (STOP) warning light.
16 Battery charge warning light.
17 Diesel engine preheating
indicator light.
18 Trip recorder zero reset.
19 Driver's seat belt warning light.
20 Passenger air bag disarming
indicator light.
21 Front, side and curtain air bags
warning light.
* According to specification.
INSTRUMENTS AND CONTROLS
18-11-2002

Maximum
Minimum
Check the level with
the dipstick and top it
up.
The figure shown is
only correct if the vehicle has been
on stable, level ground, with the
engine stopped, for 10 minutes.
No oil
The message "Top
up the oil" appears
on the multifunction
display, accompa
nied by an audible signal.
It is essential to top up the oil to the
correct level, otherwise the engine
may be damaged.
Oil gauge fault
Flashing of the seg
ments indicates a
fault.
Check the level
using the dipstick.
Consult a PEUGEOT dealer. Control module display
After switching on the ignition, three
functions are shown in succession:
– service indicator (see correspond ing section),
– engine oil level indicator,
– total distance recorder (total and trip distances).
Note: the total and trip distances are
displayed for thirty seconds, when
the ignition is switched off, on open
ing the driver's door as well as on
locking and unlocking the vehicle.
It also displays the automatic gear
box positions and programmes
selected (see corresponding sec
tion).
Engine oil level
When the ignition is switched on, the
engine oil level is indicated for
approximately 10 seconds, after the
service information. Lighting rheostat
With the lights on,
press the button to
vary the intensity of
the lighting of the
control module, the
instrument panel, the
air conditioning dis
play and the multi–function display.
When the lighting reaches the mini
mum (or maximum) setting, release
it then press again to increase (or
reduce) the brightness.
As soon as the lighting is of the
brightness required, release the
button.
Trip recorder
zero reset
With the ignition on,
press the button.
INSTRUMENTS AND CONTROLS
34
18-11-2002

YOUR 807 IN DETAIL
66
Inputting the PIN code Input your PIN code using the alphanumeric keypad and validate by pressing knobGor button #
to access the network. Connection to the network is validated by the appearance of a symbol on
the screen.
Warning: if you make three errors in succession when inputting your PIN code, your SIM card
will be blocked. To unblock it, you will need to input t he PUK code. The PUK code will be suplied
to you by the person selling your SIM card (input of the PUK code allows for 10 errors in suc
cession; after this the SIM card becomes permanently unusable).
Note: the PIN code is required each time the ignition is switched o n, unless the PIN code has
been stored in the memory or protection by PIN code is not activat ed on the SIM card.
Cancelling of PIN code request
In the menu ''Telephone functions'' select''SIM card security'' , then''Process the PIN code'' , then validate the ''Can
cel'' function.
Warning: in this case, do not lose your SIM card. Losing it would mean a nyone who finds it would be able to make unlimited calls.
Telephone function screens
Not in use
This screen indicates the presence of voice messages or minimessages (SMS) no t lis
tened to, the cumulatve time in use since the last zero reset a nd the status of your tele
phone.
In use
This screen indicates the time elapsed since the start of the co nversation, as well as
the number* or name of the person to whom you are speaking (if recorded in the index)
and the status of your telephone.
*If this option and service are available.
18-11-2002

YOUR 807 IN DETAIL
68
Mini messages (SMS)
Accessing mini messages When the buzzer sounds (if the SMS mini messages buzzer option is acti ve) and a
superimposed screen announces "Do you wish to read the new mini message
(SMS)?" , you can choose to read the mini message received by selecting an d validat
ing "YES" or postpone reading it by selecting and validating "NO", by pressing the
"ESC" button or by waiting unti the announcement disappears.
Note: the old mini messages stored and the new mini messages, the read ing of which you wish to postpone, can be con
sulted. Press the "MENU"button then validate the telematic icon, select "Mini messages (SMS)"and validate the function
"Reading of mini messages received" by pressing knob G. Then scroll through the list by turning the knob and press t he
knob to select the mini message to be read.
Sending a mini message
Note:Before typing your first mini message, check that your mini messages (SMS)
centre number is stored correctly in the submenu "Server centre number". If it is not,
any mini messages typed before this number is entered will be de leted and not sent.
In the menu "Mini messages (SMS)" validate the function "Typing of a mini mes
sage" . Type your mini message using the alphanumeric keypad and valida te it using
the "OK" button to store it or validate the "Send"button to send it.
Validation of the "Send"button enables you to enter the number of your recipient or se lect it from the directory or from the
list of calls and send the message.
"Duration of calls" menu
Select the "Duration of calls" function from the "Telephone functions" menu to consult the duration counters for the calls
made. The part counter totals the duration of the calls since the last zero reset carried out using the "Zero reset" button.
"Telephone options" menu
Select the "Telephone options" function from the "Telephone options" menu to access the functions:
• "Configure the calls" which permits activation and deactivation of the "show my number" and "automatic answering after
X rings" functions
• "Ringing options" which permits adjustment of the ringing volume for voice calls an d activation of the mini messages
(SMS) receipt buzzer.
18-11-2002

The contextual menu associated with
the "Navigation Guidance" applica
tion appears as a superimposed display,
when this is the application currently in
use in the main screen window.
This menu is limited to the following
functions:
changing of the initial route (entering of a diversion),
switching to "Selection Movement on map" mode*,
storing of the current location (postal address if available or, if it is not, the
GPS coordinates),
changing of the route calculation criteria,
stopping or resuming of guidance (displaying of the message which
changes depending on the previous
status).
General notes on the "Map"
application*
The map guidance can be displayed
in two ways:
full screen map,
reduced size map on the righthand side and zoom image of the
junction on the lefthand side.
To switch from one to the other,
press the dial for more than two sec
onds.
The "Map" application has two oper
ating modes: "Selection Movement on
map"** mode,
"Vehicle following on map"
mode.
A "Zoom" function enables you to
enlarge the map around the selected
point, in accordance with the eleven
preset levels relating to the following
scales:
100 m/cm, 200 m/cm, 500 m/cm,
1 km/cm, 2 km/cm, 5 km/cm,
10 km/cm, 20 km/cm, 50 km/cm,
100 km/cm, 200 km/cm.
This is achieved by turning the dial. This mode permits:
selection of any point on the map
to obtain guidance towards it or to
obtain information about it (postal
address if available or, if it is not,
GPS coordinates),
lateral movement on the map by means of the four directional
arrows, representing the four cardi
nal points (North, East, South,
West),
zooming in on the map in accor dance with the eleven preset
levels,
displaying of the "Map" contextual
menu.
YOUR 807 IN DETAIL
82
"Navigation Guidance"
contextual menu
"Selection Movement on map"
mode**
18-11-2002

The contextual menu associated with
the "Navigation Guidance" applica
tion appears as a superimposed display,
when this is the application currently in
use in the main screen window.
This menu is limited to the following
functions:
changing of the initial route (entering of a diversion),
switching to "Selection Movement on map" mode*,
storing of the current location (postal address if available or, if it is not, the
GPS coordinates),
changing of the route calculation criteria,
stopping or resuming of guidance (displaying of the message which
changes depending on the previous
status).
General notes on the "Map"
application*
The map guidance can be displayed
in two ways:
full screen map,
reduced size map on the righthand side and zoom image of the
junction on the lefthand side.
To switch from one to the other,
press the dial for more than two sec
onds.
The "Map" application has two oper
ating modes: "Selection Movement on
map"** mode,
"Vehicle following on map"
mode.
A "Zoom" function enables you to
enlarge the map around the selected
point, in accordance with the eleven
preset levels relating to the following
scales:
100 m/cm, 200 m/cm, 500 m/cm,
1 km/cm, 2 km/cm, 5 km/cm,
10 km/cm, 20 km/cm, 50 km/cm,
100 km/cm, 200 km/cm.
This is achieved by turning the dial. This mode permits:
selection of any point on the map
to obtain guidance towards it or to
obtain information about it (postal
address if available or, if it is not,
GPS coordinates),
lateral movement on the map by means of the four directional
arrows, representing the four cardi
nal points (North, East, South,
West),
zooming in on the map in accor dance with the eleven preset
levels,
displaying of the "Map" contextual
menu.
YOUR 807 IN DETAIL
82
"Navigation Guidance"
contextual menu
"Selection Movement on map"
mode**
18-11-2002

YOUR 807 IN DETAIL83
This mode permits:
displaying of the vehicle on the map with the route proposed by
the navigation if the guidance is
active,
zooming in on the map in accor dance with the eleven preset
levels,
displaying of the "Navigation
Guidance" contextual menu.
"Vehicle following on map" mode
From the
general menu , the main
"Map" menu offers various options
for guidance management:
switching to "Selection Movement on map" mode**,
direction of the map towards the North or in the direction of the
vehicle,
recentering of the map around the vehicle when it has disappeared **,
opening of the services selection window visible on the map,
displaying of the window for enter ing the description for recording
the current position of the vehicle
in a directory file.
Map*The contextual menu associated
with the
"Map"application and with
the "Selection Movement on
map" mode appears as a superim
posed display, when these are in use
in the main screen window.
This menu is limited to the following
functions:
displaying of the information on the location selected on the map,
selection of a location on the map as a destination,
storing of the location selected (postal address if available or, if it
is not, GPS coordinates, so that
they can be recorded in a directory
file),
switching to "Vehicle following on map" mode.
* DT colour screen only.
** During the year.
"Map" contextual menu**
18-11-2002

YOUR 807 IN DETAIL
116
TRIP COMPUTER
Each time the button on the end of the
wiper stalk is pressed, the following
sequence of data is displayed:
Monochrome screen CT
– the "vehicle" tab with:
• range, current consumption and the distance still to be driven,
– tab '1' (route '1') with:
• the distance driven and the aver age speed calculated over route
'1'
– tab '2' (route '2') with the same fea
tures.
It also permits access to the Excess
Speed Warning function.
Zero reset
When the required route is dis
played, press the button for more
than two seconds.
Monochrome screen B
the remaining range
the distance travelled
the average consumption
the current consumption
the average speed
In addition, it allows access to the
warning log information and to the
Excess speed warning function.
Zero reset
Press the stalk for more than two
seconds.
Colour screen DT
– the "Current information" with:
• the range,
• the current consumption,
• the distance still to be driven.
– 'Route 1' with:
• the distance travelled,
• the average coonsumption,
• the average speed,
– 'Route 2' with the same features.
It also permits access to the Excess
Speed Warning function.
Zero reset
When the required route is dis
played, press the button for more
than two seconds.
18-11-2002