2002 Peugeot 607 Dag ECU

PRACTICAL INFORMATION
140
CHANGING A WHEEL
Park the vehicle on level, stable
and nonslippery ground.
Apply the handbrake, engage first
or reverse gear (position
Pfor the
automatic gearbox) and switch off
the ignition.
Access to the spare wheel and the
jack in the boot
Detach the luggage net.
Lift the boot carpet using the lifting
hook. Secure this hook behind the
boot seal. Tools available
The following tools are located in the
polystyrene holder in the centre of
the spare wheel:
1
Wheelbrace.
2 Centralising tool.
3 Wheelbrace extension.
4 Jack fitted with a system which
enables it to be folded or unfold
ed rapidly.
5 Removable towing eye.
6 Alloy wheel trim remover.
7 Trim cover tool. Removal
For vehicles with alloy wheels fit
ted with wheel trims, pull the
centre trim by using tool
6in one
of the holes.
Loosen the wheel bolts.
Take the jack from the tool kit and
fold it by pressing the ends A.

PRACTICAL INFORMATION 141
Fold the jack by pressing at the
ends
Aand place it in one of the
four locations Eunderneath the
vehicle (the nearest one to the
wheel to be changed).
Extend the jack, first by hand, pul
ling the ends Athen using wheel
brace 1and the extension 3.
Remove a wheel bolt at the top
and fit the centralising tool 2in its
place.
Unscrew the other bolts and
remove the wheel.
Fitting a wheel
Position the wheel using the cen
tralising tool to assist you.
Tighten the bolts by hand and
remove the centralising tool.
Partly tighten the bolts using the
wheelbrace.
Fold the jack and remove it.
Fully tighten the bolts using the
wheelbrace.
Replace the wheel trim.
Put the tool holder back in posi
tion. This helps to keep the boot
floor in its correct position, to pre
vent any deformation of the floor
when loaded.
Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact. For your safety, always
change the wheel:
– on level, stable, nonslippery
ground,
– with the handbrake applied,
– with first or reverse gear engaged (position Pfor the
automatic gearbox),
Never go underneath a vehicle
which is supported only by a
jack (use a ramp).
After changing the wheel:
– have the tightening of the bolts and the tyre pressure checked
by a PEUGEOT dealer as soon
as possible.
– have the punctured wheel repaired and refit it to the vehi
cle as soon as possible.
Tyres fitted with the Tyre Under
Inflation Detection System.
These wheels have a pressure
sensor. Have them repaired by a
PEUGEOT dealer.

Special features of alloy wheels*
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use tool7to remove the trims before
slackening the bolts. Antitheft bolts*
If your wheels are fitted with an anti
theft bolt (one per wheel), the
chrome trim and then the plastic
cover must be removed using tool
7,
before unscrewing the bolt using one
of the two antitheft sockets (which
were given to you on delivery of your
vehicle along with the duplicate keys
and the confidential card) and the
wheel brace 1.
Note: make a careful note of the
code number engraved on the head
of the antitheft socket. This will
enable you to obtain duplicate anti
theft sockets from a Peugeot dealer.
* According to model and destination
PRACTICAL INFORMATION
142
7
Fitting the spare wheel
If your vehicle is fitted with a steel
spare wheel, when fitting it, it is
nor
mal to notice when tightening the
bolts that the washers do not come
into contact with the rim. The spare
wheel is secured by the coneshape
of each bolt.
Fitting snow tyres
If you fit snow tyres mounted on steel
wheels to your vehicle, it is essential
to use special bolts available from
your PEUGEOT dealer.
7

PRACTICAL INFORMATION 143
CHANGING A BULB
Front lights
In the engine compartment, remove the style cover secured
by one or two butterfly screws, a plastic retainer clip and
two screws.
Note:
handle the bulbs with a dry cloth.
1 Dipped beam headlamps: H755W or Xenon bulb.
WARNING: RISK OF ELECTROCUTION
Xenon bulbs must be replaced by a PEUGEOT
dealer.
2 Main beam headlamps: H155W.
 Turn the protective cover of the faulty bulb a quarter
of a turn and remove it.
 Disconnect the connector.
 PPress the end of the securing clip to free it. Change
the bulb.
 When fitting the new bulb, ensure that the direction
notches are positioned correctly and the securing
clip is fixed properly. 
Reconnect the connector.
 Refit the protective cover.
The headlamps are fitted with polycarbonate glass with a
protective coating. Do not clean them with a dry or abra
sive cloth, nor with a detergent or solvent product.
3 Side lights: W 5 W.
 Pull the socket rearwards, remove the bulb and
change it.
4 Direction indicators: PY 21 W (amber).
 Turn the bulb holder a quarter turn and remove it.
 Change the bulb.
 Refit the style cover.
Front foglamps: H1 55 W.
Note: In certain climatic conditions (low temperature,
humidity), condensation on the inside surface of the
headlamp glass is normal ; it disappears a few minutes
after the lights are switched on.

Rear lights
Rear wing lights
1 Direction indicators: PY 21 W (amber).
2 Brake lights/side lights: P21/5 W.
 Detach the luggage net.
 Lift the boot carpet with the lifting
hook. Secure this hook behind
the boot seal.
 Unclip the lower part of the sill
trim, then dislodge it by pulling
upwards.
 Remove the plastic retainer clip
securing the side trim to the
floor. 
Unclip the side trim.
 Remove the two butterfly nuts
securing the light.
 Remove the eyelet.
 Take out the lamp.
 Turn the lamp holder a quarter
turn.
 Change the faulty bulb.
 Lock the bulb holder in place.
When refitting it, ensure that the
lamp is correctly positioned and
secured.
PRACTICAL INFORMATION
144
Direction indicator repeaters:
WY 5 W (amber).
 Push the repeater forwards or
backwards and release the
assembly.
 Hold the connector and turn the
transparent cover a quarter turn.
 Change the bulb.
Amber coloured bulbs
(direction indicators and
side repeaters) must be
replaced with bulbs of
identical specification and
colour.

Rear lights
Rear wing lights
1 Direction indicators: PY 21 W (amber).
2 Brake lights/side lights: P21/5 W.
 Detach the luggage net.
 Lift the boot carpet with the lifting
hook. Secure this hook behind
the boot seal.
 Unclip the lower part of the sill
trim, then dislodge it by pulling
upwards.
 Remove the plastic retainer clip
securing the side trim to the
floor. 
Unclip the side trim.
 Remove the two butterfly nuts
securing the light.
 Remove the eyelet.
 Take out the lamp.
 Turn the lamp holder a quarter
turn.
 Change the faulty bulb.
 Lock the bulb holder in place.
When refitting it, ensure that the
lamp is correctly positioned and
secured.
PRACTICAL INFORMATION
144
Direction indicator repeaters:
WY 5 W (amber).
 Push the repeater forwards or
backwards and release the
assembly.
 Hold the connector and turn the
transparent cover a quarter turn.
 Change the bulb.
Amber coloured bulbs
(direction indicators and
side repeaters) must be
replaced with bulbs of
identical specification and
colour.

145
PRACTICAL INFORMATION
Boot lid lights
1 Reversing lights: P 21 W.
2 Fog lamps: P 21 W.
 Remove the three plastic retain
er clips securing the cover trim
(those nearest to the lamp).
 Move aside the trim. 
Turn the bulb holder a quarter
turn.
 Change the faulty bulb. Number plate lights:
W 5 W.
 Remove the transparent cover
using a screwdriver blade.
 Change the faulty bulb.

Aflat battery prevents
the engine from starting.
PRACTICAL INFORMATION
150
CHANGING A WINDSCREEN
WIPER BLADE
Placing the wiper blades in the
maintenance position
 Less than one minute after switch
ing off the ignition, activate the
windscreen wiper stalk to position
the blades in the centre of the
windscreen (maintenance posi
tion).
Replacing a blade  Lift the arm, then unclip the blade
and remove it.
 Fit the new blade and fold down
the arm.
To park the blades, switch on the
ignition and operate the wind
screen wiper stalk.
ECONOMY MODE FUNCTION
After the engine has stopped, certain
functions (windscreen wiper, electric
windows, sunroof, rear electric blind,
electric seats, audio equipment, tele
phone etc) can only be used for thir
ty minutes, to prevent discharging
the battery.
Once the thirty minutes are over, the
message "Economy mode active"
appears on the multi–function dis
play and the active functions are put
on standby.
REMOVING A MAT
When removing a mat on the driver's
or passenger's side, push back the
seat as far as possible and remove
the clips.
To remove a rear mat, push the cor
responding front seat forward and
remove the clip.
On refitting, position the mat and
press firmly to refit the securing clips.
LOAD REDUCTION
When driving, certain functions
(heated rear screen, heating system
for passenger compartment of diesel
vehicles, etc.) may be switched off
temporarily, depending on the level
of battery charge.
Reactivation of the functions on
standby is automatic, as soon as the
battery permits.
These functions are automatically
reactivated next time the vehicle is
driven.
Note:
if the telephone is being used
when economy mode starts, it will
still be possible to finish the call.