2002 MAZDA MODEL MILLENIA recommended oil

4-8
Before Driving Your Mazda
Driving Tips
Form No. 8Q47-EA-01F
•Carry emergency gear, including tire
chains, window scraper, flares, a small
shovel, jumper cables, and a small bag
of sand or salt.
Ask a Mazda dealer to perform the
following precautions:
•Have the proper ratio of antifreeze in
the radiator.
•Inspect the battery and its cables. Cold
reduces battery capacity.
•Use only cold-weather engine oil (page
8-10).
•Inspect the ignition system for damage
and loose connections.
•Use washer fluid made with
antifreeze—but don’t use engine
coolant antifreeze for washer fluid
(page 8-19).
•Don’t use the parking brake in freezing
weather as the parking brake may
freeze. Instead, shift to P and block the
rear wheels.

Snow Tires
l
Your vehicle is originally equipped with
all season radials designed to be used all
year around. In some extreme climates
you may find it necessary to replace them
with snow tires during the winter months
to further improve traction on snow and
ice covered roads.
Use snow tires on all four wheels
Don’t go faster than 120 km/h (75 mph).
Inflate snow tires 28 kPa (0.3 kgf/cm2, 4
psi) more than recommended on the tire
pressure label (driver’s door), but never
more than the maximum cold-tire
pressure shown on the tires.
Winter Driving
Mixing Tire Types:
Using tires different in size or type is
dangerous. Your vehicle’s handling
could be greatly affected and result in
an accident. Use only the same size
and type tires (snow, radial, or non-
radial) on all four wheels.
Check local regulations before using
studded tires.
WARNING
CAUTION
J76Y.book Page 8 Wednesday, March 27, 2002 5:04 PM

7-8
In Case of an Emergency
Flat Tire
Form No. 8Q47-EA-01F

Mounting the Spare Tire
1. Remove dirt and grime from the
mounting surfaces of the wheel and
hub, including the hub bolts, with a
cloth.2. Mount the spare tire.
3. Install the lug nuts with the beveled
edge inward; tighten them by hand.
Removing Dirt and Grime from
Wheels, Hubs and Hub Bolts:
When changing or replacing a tire,
not removing dirt and grime from the
mounting surfaces of the wheel, hub
and hub bolts is dangerous. The lug
nuts could loosen while driving and
cause the tire to come off, resulting in
an accident. Make sure the mounting
surfaces of the wheel, hub and lug
nuts are clean before changing or
replacing tires.
WARNINGApplying Oil and Grease to Lug Nuts,
Bolts:
Applying oil or grease to lug nuts and
bolts is dangerous. The lug nuts could
loosen while driving and cause the
tire to come off, resulting in an
accident. In addition, lug nuts and
bolts could be damaged if tightened
more than necessary. Do not apply oil
or grease to lug nuts and bolts and do
not tighten the lug nuts beyond the
recommended tightening torque.
WARNING
J76Y.book Page 8 Wednesday, March 27, 2002 5:04 PM

8-4
Maintenance and Care
Scheduled Maintenance
Form No. 8Q47-EA-01F

Schedule 1
I
: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R
: Replace
L
: Lubricate
*1: According to state and federal regulations, failure to perform maintenance on these items will not void your
emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometrage (mileage) period to ensure long-term reliability.
Maintenance
Interval
Maintenance
ItemNumber of months or kilometers (miles), whichever comes first
Months 6 12182430364248
×1000 Km 12 24 36 48 60 72 84 96
(×1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60)
Engine valve clearance Miller Cycle
Engine V6 DOHCI
Drive belts (tension)2.5 liter V6 DOHCII
Miller Cycle
Engine V6 DOHCReplace every 168,000km (105,000miles)
Engine timing belt2.5 liter V6 DOHCInspect at 96,000km (60,000miles)
Replace every 168,000km (105,000miles)
Miller Cycle
Engine V6 DOHCReplace every 96,000km (60,000miles)
Engine oilRRRRRRRR
Engine oil filterRRRRRRRR
Cooling systemII
Engine coolantReplace at first 72,000km (45,000miles) or 36 months ;
after that, every 48,000km (30,000miles) or 24 months
Idle speedII
Fuel lines and hoses
*1II
Hoses and tubes for emission*1I
Air filterRR
Spark plugs2.5 liter V6 DOHCReplace every 48,000km (30,000miles)
Miller Cycle
Engine V6 DOHCReplace every 96,000km (60,000miles)
Brake lines, hoses and connectionsII
Disc brakesII
Automatic transaxle fluid levelII
Steering operation and linkagesII
Front and rear suspension ball jointsII
Driveshaft dust bootsII
Bolts and nuts on chassis and bodyII
Exhaust system heat shieldsII
Body inspection (paint, corrosion)IIIIIIII
Compressor operationIIII
Cabin air-filter (if installed)Replace once a year or every 20,000km (12,000miles)
J76Y.book Page 4 Wednesday, March 27, 2002 5:04 PM

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8Q47-EA-01F

Schedule 2
I
: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R
: Replace
L
:Lubricate
*1: According to state and federal regulations, failure to perform maintenance on these items will not void your
emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometrage (mileage) period to ensure long-term reliability.
*2: If the vehicle is operated in cold districts { below -18 degrees C (0 degrees F) }, replace the timing belt at
96,000km (60,000miles).
Maintenance
Interval
Maintenance
ItemNumber of months or kilometers (miles), whichever comes first
Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 Km 8 1624324048566472808896
(×1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60)
Engine valve clearanceMiller Cycle Engine
V6 DOHCI
Drive belts (tension)2.5 liter V6 DOHCII
Miller Cycle Engine
V6 DOHCReplace every 168,000km (105,000miles)
Engine timing belt2.5 liter V6 DOHC
*2Inspect at 96,000km (60,000miles)
Replace every 168,000km (105,000miles)
Miller Cycle Engine
V6 DOHCReplace every 96,000km (60,000miles)
Engine oilPuerto RicoReplace every 5,000km (3,000miles) or 3 months
othersRRRRRRRRRRRR
Engine oil filterRRRRRRRRRRRR
Cooling systemII
Engine coolantReplace at first 72,000km (45,000 miles) or 36 months ;
after that, every 48,000km (30,000miles) or 24 months
Engine coolant levelIIIIIIIIIIII
Idle speedI I
Fuel lines and hoses
*1I I
Hoses and tubes for emission*1I
Air filter
I *1R
I *1R
Spark plugs 2.5 liter V6 DOHCReplace every 48,000km (30,000miles)
Miller Cycle Engine
V6 DOHCReplace every 96,000km (60,000miles)
Function of all lightsIIIIIIIIIIII
Brake lines, hoses and connectionsII
Brake fluid levelIIIIIIIIIIII
Disc brakesIIII
Automatic transaxle fluid levelII
Tire inflation pressure and tire wearIIIIIIIIIIII
Steering operation and linkagesII
J76Y.book Page 5 Wednesday, March 27, 2002 5:04 PM

8-10
Maintenance and Care
Owner Maintenance
Form No. 8Q47-EA-01F

Recommended Oil
Oil container labels provide important
information.
The quality designation SG, SH, SJ,
SL,

or ILSAC
must be on the label.
Engine oil viscosity, or thickness, has an
effect on fuel economy and cold-weather
operation (starting and oil flow).
Low-viscosity engine oils can provide
improved fuel economy and cold-weather
performance.
But high-temperature weather conditions
require higher-viscosity engine oils for
satisfactory lubrication.When choosing an oil, consider the
temperature range your vehicle will
operate in before the next oil change.
Then select the recommended viscosity
from this chart.
Energy conserving oils are recommended.
A chief contribution they make to fuel
economy is reducing the amount of fuel
necessary to overcome engine friction.

Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal
operating temperature.
3. Turn it off and wait 5 minutes for the
oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
Engine Oil
SAEFORGASOLINEENGINES10W-30
(ILSAC)
–30–20–100 1020304050
–20 0 20 40 60 80 100 120
5W-30
10W-30
Using oils of viscosity besides those
recommended for specific temperature
ranges could result in engine damage.
CAUTION
Full
LowOK
J76Y.book Page 10 Wednesday, March 27, 2002 5:04 PM

8-43
Maintenance and Care
Appearance Care
Form No. 8Q47-EA-01F

Dashboard Precautions
Prevent caustic solutions such as perfume
and cosmetic oils from contacting the
dashboard. They’ll damage and discolor
it. If these solutions get on the dashboard,
wipe them off immediately.

Cleaning the Upholstery and
Interior Trim
Vi ny l
Remove dust and loose dirt from vinyl
with a whisk broom or vacuum cleaner.
Clean vinyl with a leather-and-vinyl
cleaner.
Leather
Real leather isn’t uniform and may have
scars, scratches, and wrinkles. Clean it
with a leather cleaner or mild soap.
Wipe it with a damp
soft cloth; then dry
and buff it with a dry
soft cloth.
Fabric
Remove dust and loose dirt from fabric
with a whisk broom or vacuum cleaner.
Clean it with a mild soap solution good
for upholstery and carpets. Remove fresh
spots immediately with a fabric spot
cleaner.To keep the fabric looking clean and
fresh, take care of it. Otherwise its color
will be affected, it can be stained easily,
and its fire-resistance may be reduced.

Cleaning the Lap/Shoulder Belt
We b b i n g
Clean the webbing with a mild soap
solution recommended for upholstery or
carpets. Follow instructions. Don’t bleach
or dye the webbing; this may weaken it.
After cleaning the belts, thoroughly dry
the belt webbing and make sure there is
no remaining moisture before retracting
them.
Interior Care
Do not use glazing agents.
Glazing agents contain ingredients
which may cause discoloration,
wrinkling, cracks and peeling.
CAUTION
Use only recommended cleaners and
procedures. Others may affect
appearance and fire-resistance.
Damaged Seat Belt:
Using damaged seat belts is
dangerous. In a collision, damaged
belts cannot provide adequate
protection. Have your Authorized
Mazda Dealer replace damaged belts
immediately.
CAUTION
WARNING
J76Y.book Page 43 Wednesday, March 27, 2002 5:04 PM

10-4
Form No. 8Q47-EA-01F
Specifications

Engine

Electrical System

Lubricant Quality
* Refer to the recommended SAE viscosity numbers on page 8-10.
Specifications
ItemModel
2.5 liter V6 DOHC Miller Cycle Engine V6 DOHC
Bore×Stroke 84.5 × 74.2 mm (3.33 × 2.92 in) 80.3 × 74.2 mm (3.16 × 2.92 in)
Displacement 2,496 ml (2,496 cc, 152.3 cu in) 2,254 ml (2,254 cc, 137.5 cu in)
Compression ratio 9.2 10.0
ItemModel
2.5 liter V6 DOHC Miller Cycle Engine V6 DOHC
BatteryMaintenance-free,
12V-48AH/5HR,
52AH/5HR (Cold areas)Maintenance-free,
12V-52AH/5HR,
55AH/5HR (Cold areas)
Alternator 12V-110 A
Starter 12V-1.6 kW 12V-2.0 kW
Spark-plug
numberNGK ZFR5F-11, ZFR6F-11 PZFR5F, PZFR6F
DENSO—PKJ16CR8, PKJ20CR8
CHAMPION—RC8PMPA, RC10PMPA
Spark-plug gap 1.0—1.1 mm (0.040—0.043 in) 0.7—0.8 mm (0.028—0.031 in)
LubricantClassification
API Service ILSAC
Engine oil
*
SG (Energy Conserving II)—
SH (Energy Conserving II) GF-I
SJ GF-II
SL GF-III
Lubricant Classification
Automatic transaxle fluid
ATF M-III or equivalent (e.g. Dexron
® III)
Power steering fluid
ATF M-III or equivalent (e.g. Dexron® III)
Brake fluid SAE J1703 or FMVSS116 DOT-3
J76Y.book Page 4 Wednesday, March 27, 2002 5:04 PM