2002 MAZDA 6 light

ON-BOARD DIAGNOSTIC
K2–139
K2
End Of SieDTC P0720A6E577018901211
10INSPECT INPUT/TURBINE SPEED SENSOR
CONNECTOR FOR POOR CONNECTION
•Disassemble the transaxle.
•Disconnect input/turbine speed sensor
connector.
•Check for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Are terminals okay?Yes Go to next step.
No Repair terminals, then go to Step 12.
11INSPECT INPUT/TURBINE SPEED SENSOR
RESISTANCE
•Measure resistance between input/turbine
speed sensor.
•Is resistance within 513—627 ohms between
input/turbine speed sensor connector terminal
A and B (part side)?Yes Repair or replace coupler component, then go to next step.
No Replace input/turbine speed sensor, then go to next step.
12VERIFY TROUBLESHOOTING OF DTC P0715
COMPLETED
•Make sure to reconnect all disconnected
connectors.
•Clear DTC from memory using WDS or
equivalent.
•Drive vehicle with vehicle speed 40 km/h {25
mph} or above and engine speed 1,500 rpm
or above for 2 second or more
•Repeat Step ii two times.
•Is same DTC present?Yes Replace TCM, then go to next step.
(See K2–96 TCM REMOVAL/INSTALLATION.)
No Go to next step.
13VERIFY AFTER REPAIR PROCEDURE
•Perform “After Repair Procedure”.
(See K2–124 AFTER REPAIR PROCEDURE.)
•Is there any DTC present?Yes Go to applicable DTC inspection.
No Troubleshooting completed. STEP INSPECTION ACTION
DTC P0720 Vehicle speedometer sensor (VSS) malfunction (open/short)
DETECTION
CONDITION•Parking gear rotation detected by VSS is 150 rpm (Vehicle speed: 5—6 km/h) or less while intermediate
sensor signal is 1,400 rpm or greater in D range for 2 second or more.
Diagnostic support note:
•This is a continuous monitor (CCM).
•MIL illuminates if TCM detects the above malfunction conditions in two consecutive drive cycles.
•PENDING CODE is available.
•FREEZE FRAME DATA is available.
•AT warning light indication.
•DTC is stored in TCM memory.
POSSIBLE
CAUSE•Open circuit between vehicle speedometer sensor terminal B and TCM terminal 1M
•Open circuit between vehicle speedometer sensor terminal A and TCM terminal 1V
•Short to ground between vehicle speedometer sensor terminal B and TCM terminal 1M
•Short to ground between vehicle speedometer sensor terminal A and TCM terminal 1V
•Vehicle speedometer sensor malfunction
•Damaged connectors between vehicle speedometer sensor to TCM
•TCM malfunction

K2–142
ON-BOARD DIAGNOSTIC
End Of SieDTC P0740A6E577018901212
Diagnostic procedure
12VERIFY TROUBLESHOOTING OF DTC P0720
COMPLETED
•Make sure to reconnect all disconnected
connectors.
•Clear DTC from memory using WDS or
equivalent.
•Drive vehicle with vehicle speed 40 km/h {25
mph} or above for 2 second or more
•Is same DTC present?Yes Replace TCM, then go to next step.
(See K2–96 TCM REMOVAL/INSTALLATION.)
No Go to next step.
13VERIFY AFTER REPAIR PROCEDURE
•Perform “After Repair Procedure”.
(See K2–124 AFTER REPAIR PROCEDURE.)
•Is there any DTC present?Yes Go to applicable DTC inspection.
No Troubleshooting completed. STEP INSPECTION ACTION
DTC P0740 TCC system malfunction
DETECTION
CONDITION•RPM difference between crankshaft (engine speed signal) and reverse clutch drum (input/turbine speed
sensor signal) exceeds the pre-programmed value.
Diagnostic support note:
•This is continuous monitor (CCM).
•MIL illuminates if TCM detects the above malfunction conditions in two consecutive drive cycles.
•PENDING CODE is available.
•FREEZE FRAME DATA is available.
•AT warning light does not indication.
•DTC is stored in TCM memory.
POSSIBLE
CAUSE•ATF level low.
•Deteriorated ATF.
•TCC solenoid valve and pressure control solenoid stuck.
•Line pressure low.
•Oil pump malfunction.
•Control valve stuck
•Torque convert clutch malfunction
•TCM malfunction.
STEP INSPECTION ACTION
1VERIFY FREEZE FRAME DATA HAS BEEN
RECORDED
•Has FREEZE FRAME PID DATA been
recorded?Yes Go to next step.
No Record FREEZE FRAME PID DATA on repair order, then
go to next step.
2VERIFY RELATED REPAIR INFORMATION
AVAILABILITY
•Check for related Service Bulletins and/or on-
line repair information availability.
•Is any related repair information available?Yes Perform repair or diagnosis according to available repair
information.
•If vehicle is not repaired, go to next step.
No Go to next step.
3CHECK ATF CONDITION
•Turn ignition key to OFF.
•Check ATF condition.
—Clear red: Normal
—Milky: Water mixed in fluid
—Reddish brown: Deteriorated ATF
•Is it okay?
(See K2–78 Automatic Transaxle Fluid (ATF)
Condition Inspection.)Yes Go to next step.
No If ATF color milky or reddish brown, replace ATF, then go to
Step 5.
(See K2–80 AUTOMATIC TRANSAXLE FLUID (ATF)
REPLACEMENT.)
4CHECK ATF LEVEL
•Start engine.
•Warm up ATX.
•Is ATF level within specification?
(See K2–79 Automatic Transaxle Fluid (ATF)
Level Inspection.)Yes Go to next step.
No Adjust ATF level, then go to Step 9.
(See K2–79 Automatic Transaxle Fluid (ATF) Level
Inspection.)

K2–144
ON-BOARD DIAGNOSTIC
DTC P0743A6E577018901213
DTC P0743 Torque converter clutch (TCC) solenoid valve circuit malfunction (open/short)
DETECTION
CONDITION•Open or short in TCC solenoid signal system (while TCM monitors solenoid output voltage, the voltage that
differs from the ON/OFF signal output by CPU in TCM is detected).
Diagnostic support note:
•This is continuous monitor (CCM).
•MIL illuminates if TCM detects the above malfunction condition during first drive cycle.
•PENDING CODE is not available.
•FREEZE FRAME DATA is available.
•AT warning light does not indication.
•DTC is stored in TCM memory.
POSSIBLE
CAUSE•Open circuit between TCC solenoid valve terminal A and TCM terminal 2S
•Short to ground between TCC solenoid valve terminal A and TCM terminal 2S
•Short to power between TCC solenoid valve terminal A and TCM terminal 2S
•TCC solenoid valve malfunction
•Damage connector between TCC solenoid valve and TCM
•TCM malfunction
2PTCM
HARNESS SIDE CONNECTORTERMINAL COMPONENT
NO.1(12-PIN)
HARNESS SIDE CONNECTOR
COUPLER COMPONENT
(10-PIN)
PART SIDE CONNECTORTCC SOLENOID VALVE
HARNESS SIDE CONNECTORAT X
CPU
CPU2S
2PB
JA C
A
B TCM
TCC SOLENOID VALVE

K2–146
ON-BOARD DIAGNOSTIC
End Of SieDTC P0748A6E577018901214
11INSPECT TERMINAL COMPONENT NO.1 (12-
PIN) CIRCUIT FOR SHORT TO POWER
•Turn ignition key to ON (engine OFF).
•Check voltage at terminal component No.1 (12-
pin) terminal H (harness-side).
•Is voltage 0 V?Yes Go to next step.
No Repair or replace harness, then go to Step 13.
12INSPECT TCM CIRCUIT FOR SHORT TO
GROUND
•Turn ignition key to OFF.
•Check continuity between TCM terminal 2S
(harness-side) and body ground.
•Is there any continuity?Yes Repair or replace harness, then go to next step.
No Go to next step.
13VERIFY TROUBLESHOOTING OF DTC P0743
COMPLETED
•Make sure to reconnect all disconnected
connectors.
•Clear DTC from memory using WDS or
equivalent.
•Drive vehicle in D range and make sure that
gears shift smoothly from 1GR to 5GR.
•Is same DTC present?Yes Replace TCM, then go to next step.
(See K2–96 TCM REMOVAL/INSTALLATION.)
No Go to next step.
14VERIFY AFTER REPAIR PROCEDURE
•Perform “After Repair Procedure”.
(See K2–124 AFTER REPAIR PROCEDURE.)
•Is there any DTC present?Yes Go to applicable DTC inspection.
No Troubleshooting completed. STEP INSPECTION ACTION
DTC P0748 Pressure control solenoid circuit malfunction (open/short)
DETECTION
CONDITION•Open or short in pressure control solenoid signal system (while TCM monitors solenoid output voltage, the
voltage that differs from the ON/OFF signal output by CPU in TCM is detected).
Diagnostic support note:
•This is a continuous monitor (CCM).
•MIL does not illuminate.
•PENDING CODE is not available.
•FREEZE FRAME DATA is not available.
•AT warning light indication.
•DTC is stored in TCM memory.
POSSIBLE
CAUSE•Open circuit between pressure control solenoid terminal A and TCM terminal 2Y
•Short to ground between pressure control solenoid terminal A and TCM terminal 2Y
•Short to power between pressure control solenoid terminal A and TCM terminal 2Y
•Pressure control solenoid malfunction
•Damaged connector between pressure control solenoid valve and TCM
•TCM malfunction

ON-BOARD DIAGNOSTIC
K2–149
K2
End Of SieDTC P0751A6E577018901215
Diagnostic procedure
End Of Sie
13VERIFY AFTER REPAIR PROCEDURE
•Perform “After Repair Procedure”.
(See K2–124 AFTER REPAIR PROCEDURE.)
•Is there any DTC present?Yes Go to applicable DTC inspection.
No Troubleshooting completed. STEP INSPECTION ACTION
DTC P0751 Shift solenoid A malfunction (stuck off)
DETECTION
CONDITION•Difference between actual gear ratio and gear ratio set in TCM is large.
Diagnostic support note:
•This is a continuous monitor (CCM).
•MIL illuminates if TCM detects the above malfunction condition.
•PENDING CODE is not available.
•FREEZE FRAME DATA is available.
•AT warning light does not indication.
•DTC is stored in TCM memory.
POSSIBLE
CAUSE•Shift solenoid A malfunction
•Shift valve A stuck
•TCM malfunction
STEP INSPECTION ACTION
1VERIFY FREEZE FRAME DATA HAS BEEN
RECORDED
•Has FREEZE FRAME PID DATA been
recorded?Yes Go to next step.
No Record FREEZE FRAME PID DATA on repair order, then
go to next step.
2VERIFY RELATED REPAIR INFORMATION
AVAILABILITY
•Check for related Service Bulletins and/or on-
line repair information availability.
•Is any related repair information available?Yes Perform repair or diagnosis according to available repair
information.
•If vehicle is not repaired, go to next step.
No Go to next step.
3CHECK FOR DTC
•Turn ignition key to ON (engine OFF).
•Inspect DTC.
•Is DTC outputted?Yes Follow applicable DTC inspection procedure.
No Go to next step.
4CHECK ATF CONDITION
•Turn ignition key to OFF.
•Check ATF condition.
—Transparent red: Normal
—Milky: Water mixed in fluid
—Reddish brown: Deteriorated ATF
•Is it okay?
(See K2–78 Automatic Transaxle Fluid (ATF)
Condition Inspection.)Yes replace control valve body, then go to next step.
No If ATF color milky or reddish brown, reaper or replace ATX,
then go to next step.
5VERIFY TROUBLESHOOTING OF DTC P0751
COMPLETED.
•Make sure to reconnect all disconnected
connectors.
•Clear DTC from memory using WDS or
equivalent.
•Start engine.
•Warm up ATX.
•Drive vehicle in D range and make sure that
gears shift smoothly from 1GR to 5GR.
•Is same DTC present?Yes Replace TCM, then go to next step.
(See K2–96 TCM REMOVAL/INSTALLATION.)
No Go to next step.
6VERIFY AFTER REPAIR PROCEDURE
•Perform “After Repair Procedure”.
(See K2–124 AFTER REPAIR PROCEDURE.)
•Is there any DTC present?Yes Go to applicable DTC inspection.
No Troubleshooting completed.

K2–150
ON-BOARD DIAGNOSTIC
DTC P0752A6E577018901216
Diagnostic procedure
End Of Sie
DTC P0752 Shift solenoid A malfunction (stuck on)
DETECTION
CONDITION•Difference between actual gear ratio and gear ratio set in TCM is large.
Diagnostic support note:
•This is a continuous monitor (CCM).
•MIL illuminates if TCM detects the above malfunction.
•PENDING CODE is not available.
•FREEZE FRAME DATA is available.
•AT warning light does not indication.
•DTC is stored in TCM memory.
POSSIBLE
CAUSE•Shift solenoid A malfunction
•Shift valve A stuck
•TCM malfunction
STEP INSPECTION ACTION
1VERIFY FREEZE FRAME DATA HAS BEEN
RECORDED
•Has FREEZE FRAME PID DATA been
recorded?Yes Go to next step.
No Record FREEZE FRAME PID DATA on repair order, then
go to next step.
2VERIFY RELATED REPAIR INFORMATION
AVAILABILITY
•Check for related Service Bulletins and/or on-
line repair information availability.
•Is any related repair information available?Yes Perform repair or diagnosis according to available repair
information.
•If vehicle is not repaired, go to next step.
No Go to next step.
3CHECK FOR DTC
•Turn ignition key to ON (engine OFF).
•Inspect DTC.
•Is DTC outputted?Yes Follow applicable DTC inspection procedure.
No Go to next step.
4CHECK ATF CONDITION
•Turn ignition key to OFF.
•Check ATF condition.
—Transparent red: Normal
—Milky: Water mixed in fluid
—Reddish brown: Deteriorated ATF
•Is it okay?
(See K2–78 Automatic Transaxle Fluid (ATF)
Condition Inspection.)Yes replace control valve body, then go to next step.
No If ATF color milky or reddish brown, reaper or replace ATX,
then go to next step.
5VERIFY TROUBLESHOOTING OF DTC P0752
COMPLETED.
•Make sure to reconnect all disconnected
connectors.
•Clear DTC from memory using WDS or
equivalent.
•Start engine.
•Warm up ATX.
•Drive vehicle in D range and make sure that
gears shift smoothly from 1GR to 5GR.
•Is same DTC present?Yes Replace TCM, then go to next step.
(See K2–96 TCM REMOVAL/INSTALLATION.)
No Go to next step.
6VERIFY AFTER REPAIR PROCEDURE
•Perform “After Repair Procedure”.
(See K2–124 AFTER REPAIR PROCEDURE.)
•Is there any DTC present?Yes Go to applicable DTC inspection.
No Troubleshooting completed.

ON-BOARD DIAGNOSTIC
K2–151
K2
DTC P0753A6E577018901217
DTC P0753 Shift solenoid A circuit malfunction (open/short)
DETECTION
CONDITION•Open or short in shift solenoid A signal system (while TCM monitors solenoid output voltage, the voltage
that differs from the ON/OFF signal output by CPU in TCM is detected).
Diagnostic support note:
•This is a continuous monitor (CCM).
•MIL illuminates if TCM detects the above malfunction condition during first drive cycle.
•PENDING CODE is not available.
•FREEZE FRAME DATA is available.
•AT warning light indication.
•DTC is stored in TCM memory.
POSSIBLE
CAUSE•Open circuit between shift solenoid A terminal A and TCM terminal 2W
•Short to ground between shift solenoid A terminal A and TCM terminal 2W
•Short to power between shift solenoid A terminal A and TCM terminal 2W
•Shift solenoid A malfunction
•Damage connector between shift solenoid A and TCM
•TCM malfunction
CPU
I
K
A
2W
TCM
AT X
TCM
HARNESS SIDE CONNECTOR
TERMINAL COMPONENT
NO.1(12-PIN)
HARNESS SIDE CONNECTORSHIFT SOLENOID A
COUPLER COMPONENT
(10-PIN)
PART SIDE CONNECTORSHIFT SOLENOID A
HARNESS SIDE CONNECTOR

ON-BOARD DIAGNOSTIC
K2–153
K2
End Of Sie
DTC P0756A6E577018901218
Diagnostic procedure
11INSPECT TERMINAL COMPONENT NO.1 (12-
PIN) CIRCUIT FOR SHORT TO POWER
•Turn ignition key to ON (engine OFF).
•Check voltage at terminal component No.1 (12-
pin) terminal I (harness-side).
•Is voltage 0 V?Yes Go to next step.
No Repair or replace harness, then go to Step 13.
12INSPECT TCM CIRCUIT FOR SHORT TO
GROUND
•Turn ignition key to OFF.
•Check continuity between TCM terminal 2W
(harness-side) and body ground.
•Is there any continuity?Yes Repair or replace harness, then go to next step.
No Go to next step.
13VERIFY TROUBLESHOOTING OF DTC P0753
COMPLETED
•Make sure to reconnect all disconnected
connectors.
•Clear DTC from memory using WDS or
equivalent.
•Drive vehicle in D range and make sure that
gears shift smoothly from 1GR to 5GR.
•Is same DTC present?Yes Replace TCM, then go to next step.
(See K2–96 TCM REMOVAL/INSTALLATION.)
No Go to next step.
14VERIFY AFTER REPAIR PROCEDURE
•Perform “After Repair Procedure”.
(See K2–124 AFTER REPAIR PROCEDURE.)
•Is there any DTC present?Yes Go to applicable DTC inspection.
No Troubleshooting completed. STEP INSPECTION ACTION
DTC P0756 Shift solenoid B malfunction (stuck off)
DETECTION
CONDITION•Difference between actual gear ratio and gear ratio set in TCM is large.
Diagnostic support note:
•This is a continuous monitor (CCM).
•MIL illuminates if TCM detects the above malfunction condition.
•PENDING CODE is not available.
•FREEZE FRAME DATA is available.
•AT warning light does not indication.
•DTC is stored in TCM memory.
POSSIBLE
CAUSE•Shift solenoid B malfunction.
•Shift valve B stuck
•TCM malfunction
STEP INSPECTION ACTION
1VERIFY FREEZE FRAME DATA HAS BEEN
RECORDED
•Has FREEZE FRAME PID DATA been
recorded?Yes Go to next step.
No Record FREEZE FRAME PID DATA on repair order, then
go to next step.
2VERIFY RELATED REPAIR INFORMATION
AVAILABILITY
•Check for related Service Bulletins and/or on-
line repair information availability.
•Is any related repair information available?Yes Perform repair or diagnosis according to available repair
information.
•If vehicle is not repaired, go to next step.
No Go to next step.
3CHECK FOR DTC
•Turn ignition key to ON (engine OFF).
•Inspect DTC.
•Is DTC outputted?Yes Follow applicable DTC inspection procedure.
No Go to next step.