2002 LAND ROVER DISCOVERY engine

MAINTENANCE
PROCEDURES 10-23
Power steering, suspension
ACE pipes
1.Check for fluid leaks from power steering and
suspension systems.
2.Check ACE pipes and unions for chafing, leaks
and corrosion and that all pipes and hoses are
correctly routed and secure.
Engine, gearbox, transfer box and axles
Check
1.Check for oil leaks from engine, gearbox
(manual and automatic), transfer box and front
and rear axles; pay particular attention to areas
around oil seals.
Exhaust system
Check
1.Check for signs of exhaust system leaks,
damage and security.
Steering box and front suspension
Check/tighten steering box fixings
1.Check steering box fixings and tighten to 90
Nm (66 lbf.ft).
Check/tighten front axle suspension fixings

MAINTENANCE
PROCEDURES 10-27
2.Check security of fixings.

+ TORQUE WRENCH SETTINGS,
Front suspension.

+ TORQUE WRENCH SETTINGS, Rear
suspension.
Towing bracket
Check
1.Check security of towing bracket.
Engine mountings - V8 engine
Check for security and condition
1.Check condition of Transfer box - RH mounting
rubber.
2.Check condition of Transfer box - LH mounting
rubber.
3.Check condition of Engine - LH mounting
rubber.

MAINTENANCE
10-28 PROCEDURES
4.Check condition of Engine - RH mounting
rubber
5.Check tightness of all mounting bolts.

+ TORQUE WRENCH SETTINGS,
Engine V8.
Road/roller test
WARNING: Roller test must be restricted to 3
mph (5 km/h). If 2 wheel rolling road is to be used,
disconnect propeller shaft from the transfer box
output shaft driving the axle which is NOT on the
rolling road.Testing
1. 2 wheel rolling road: Engage differential lock
using a 10 mm open ended spanner on flats
machined on differential lock selector
shaft.Switch on ignition and check that the
differential lock, electronic brake
distribution and hill descent warning lamps
are illuminated.
2.Check for correct operation of starter switch,
ensure engine starts correctly; leave the engine
running.
3.Check for correct operation of starter switch,
ensure engine starts correctly; leave the engine
running.
4.With vehicle stationary, turn steering from lock
to lock. Check for smooth operation and ensure
there is no undue noise from power steering
pump or drive belt.
5.Depress clutch and select all gears in turn,
check for smooth, notch free engagement.
6. Check all vehicle systems for correct
operation.
7.Check for unusual engine, gearbox and
suspension noises.
8.Check braking system operation.
9.Check for smooth gear engagement.
10.Check engine performance.
11.Check operation of all instruments and warning
devices where practicable.

ENGINE - TD5
DESCRIPTION AND OPERATION 12-1-1
ENGIN E - T d5 DESCRIPTION AND OPERAT ION
Td5 Engine

ENGINE - TD5
12-1-2 DESCRIPTION AND OPERATION
Cylinder block components

ENGINE - TD5
DESCRIPTION AND OPERATION 12-1-3
1Oil dipstick tube
2Screw – oil dipstick tube to camshaft carrier
3Oil dipstick
42nd piston ring
5Piston
6Small-end bush
7Connecting rod
8Big-end bearing cap
9Connecting rod bolt (2 off per connecting rod)
10Top piston ring
11Oil control ring
12Circlips (2 off per gudgeon pin)
13Gudgeon pin
14Big-end bearing shells
15Dowels – cylinder head (2 off)
16Clutch housing shim plate
17 Crankshaft rear oil seal and housing
18Screws – crankshaft seal housing to engine
block (5 off)
19Bolts – clutch housing shim plate to engine
block (2 off)
20Main oil gallery plug (rear)
21Oil filter adaptor gasket
22Oil filter adaptor thermostat
23Oil filter adaptor assembly
24Oil filter adaptor insert25Oil filter adaptor to cylinder block bolts (3 off)
26Oil filter
27Oil pressure switch
28Oil cooler banjo bolts (2 off)
29O-rings – oil cooler banjo bolts (2 off)
30Oil cooler to cylinder block bolts (7 off)
31Centrifuge assembly
32Centrifuge to cylinder block bolts (3 off)
33Centrifuge oil drain pipe
34Oil drain pipe to sump gasket
35Centrifuge to oil drain pipe gasket
36Oil cooler plugs (3 off)
37Oil cooler assembly
38Oil cooler matrix 'O-rings' (2 off)
39Oil cooler matrix
40Oil cooler gasket
41Coolant and PAS pump assembly bracket
42Bracket bolts (5 off + 1 stud/nut)
43Cylinder block
44Dowels to timing block cover (2 off)
45Oil gallery delivery plug
46Cross drilling plug
47Coolant jacket plug
48Core plugs (3 off)

ENGINE - TD5
12-1-4 DESCRIPTION AND OPERATION
Crankshaft, sump and oil pump

ENGINE - TD5
DESCRIPTION AND OPERATION 12-1-5
1Crankshaft pulley bolt
2TV Damper to crankshaft pulley bolts (3 off)
3TV Damper
4Crankshaft pulley
5Woodruff key
6Crankshaft
7Crankshaft to flywheel dowel
8Spigot bush
9Flywheel to crankshaft bolts (8 off)
10Flywheel assembly (Manual shown)
11Main bearing shells (6 pairs)
12Main bearing caps (6 off)
13Main bearing cap bolts (12 off)
14Thrust washer (2 off at No. 3 Main bearing)
15Piston lubrication jets (5 off)
16Piston lubrication jet cap head screw (5 off)
17Stiffener plate (oil pump integral)18Stiffener plate / oil pump assembly to cylinder
block bolts (22 off)
19Oil pick-up pipe O-ring
20Oil pick-up pipe inserts (2 x 6mm; 1 x 10mm)
21Upper oil pick-up pipe
22Oil pick-up pipe gauze
23Lower oil pick-up pipe
24Sump
25Oil drain plug seal
26Oil drain plug
27Sump to cylinder block bolts (20 off)
28Sump gasket
29Oil pick-up pipe bolts (3 off)
30Oil pump
31Chain lubrication jet
32Chain lubrication jet screw
33Stiffener to cylinder block dowel (2 off)