2002 LAND ROVER DISCOVERY fuel

GENERAL INFORMATION
03-16
Fuel Handling Precautions
Fuel vapour is highly flammable and in confined
spaces is also explosive and toxic. The vapour is
heavier than air and will always fall to the lowest
level. The vapour can be easily distributed
throughout a workshop by air currents;
consequently, even a small spillage of fuel is
potentially very dangerous.
The following information provides basic precautions
which must be observed if fuel is to be handled
safely. It also outlines other areas of risk which must
not be ignored. This information is issued for basic
guidance only, if in doubt consult your local Fire
Officer.
General
Always have a fire extinguisher containing FOAM,
CO
2, GAS or POWDER close at hand when handling
or draining fuel or when dismantling fuel systems.
Fire extinguishers should also be located in areas
where fuel containers are stored.
Always disconnect the vehicle battery before
carrying out dismantling or draining work on a fuel
system.
Whenever fuel is being handled, drained or stored, or
when fuel systems are being dismantled, all forms of
ignition must be extinguished or removed; any
leadlamps must be flameproof and kept clear of
spillage.
WARNING: No one should be permitted to repair
components associated with fuel without first
having specialist training.
WARNING: Do not remove fuel system
components while the vehicle is over a pit.
Fuel tank draining
Fuel tank draining should be carried out in
accordance with the procedure outlined in the FUEL
DELIVERY section of this manual and observing the
following precautions.
WARNING: Fuel must not be extracted or drained
from any vehicle while it is over a pit. Extraction
or draining of fuel must be carried out in a well
ventilated area.
The capacity of containers must be more than
adequate for the amount of fuel to be extracted or
drained. The container should be clearly marked
with its contents and placed in a safe storage
area which meets the requirements of local
authority regulations.Fuel tank removal
When the fuel line is secured to the fuel tank outlet by
a spring steel clip, the clip must be released before
the fuel line is disconnected or the fuel tank is
removed. This procedure will avoid the possibility of
fumes in the fuel tank being ignited when the clip is
released.
As an added precaution, fuel tanks should have a
'FUEL VAPOUR' warning label attached to them as
soon as they are removed from the vehicle.
Fuel tank repairs - plastic tank
No attempt should be made to repair a plastic fuel
tank. If the structure of the tank is damaged, a new
tank must be fitted.
Body repairs
Plastic fuel pipes are particularly susceptible to heat,
even at relatively low temperature, and can be
melted by heat conducted from some distance away.
When body repairs involve the use of heat, all fuel
pipes which run in the vicinity of the repair area must
be removed, and the tank outlet plugged.
WARNING: If welding is to be carried out in the
vicinity of the fuel tank, the fuel system must be
drained and the tank removed before welding
commences.

GENERAL DATA
04-4
Engine - V8
General
Cylinder arrangement 90° V8, numbered from the front of the engine:

Left bank cylinders 1, 3, 5 and 7

Right bank cylinders 2, 4, 6 and 8
Bore 94.00 mm (3.70 in)
Stroke:

4.0 litre

4.6 litre71.04 mm (2.80 in)
81.92 mm (3.22 in)
Capacity:

4.0 litre

4.6 litre3950 cm
3 (241 in3)
4554 cm3 (278 in3)
Firing order 1 - 8 - 4 - 3 - 6 - 5 - 7 - 2
Compression ratio:

Low - 4.0 litre 8.23:1

High - 4.0 and 4.6 litre 9.35:1
Direction of rotation Clockwise viewed from the front of the engine
Maximum power - 4.0 litre:

Low compression ratio 132 kW (177 bhp) at 4750 rev/min

High compression ratio - UK/Japan/ROW 136 kW (182 bhp) at 4750 rev/min

High compression ratio - NAS 140 kW (187 bhp) at 4750 rev/min
Maximum power - 4.6 litre 162 kW (217 bhp) at 4750 rev/min
Maximum engine speed:

Continuous5000 rev/min

Intermittent 5250 rev/min
Weight (fully dressed, wet)

Manual 194 Kg (435 lb)

Automatic 179 Kg (402 lb)
Dimensions:

Length - Manual 767 mm (30.2 in) (Including fan)

Length - Automatic 777 mm (30.5 in) (Including fan and drive plate)

Width 652 mm (25.7 in)

Height 746 mm (29.4 in)
Spark plugs:

Make/Type - 4.0 litre Champion RC11 PYP B4

Make/type - 4.6 litre Champion RN11 YCC

Gap - 4.0 and 4.6 litre 1.00 ± 0.05 mm (0.040 ± 0.002 in) Non-adjustable
Coils:

Make Bosch 0221 503 407

Type Twin coils
Fuel injection system:

Make Bosch Motronic 5.2.1 Type 4146

Type Multiport fuel injection, electronically controlled with electro-
mechanical injectors

GENERAL DATA
04-5
Idle speed:

All loads off 660 ± 50 rev/min

Base idle speed Non-adjustable

Idle air control (IAC) valve position Checked via TestBook
CO at idle:

Catalyst vehicles 0.5 %

Non-catalyst vehicles 0.5 - 1.0 %
Valve timing
Inlet valves:

Opens 28° BTDC

Closes 77° ABDC
Exhaust valves:

Opens 66° BBDC

Closes 39° ATDC
Fuel grade:

High compression catalyst vehicles 95 RON minimum unleaded

Low compression catalyst vehicles 91 RON minimum unleaded

Non-catalyst vehicles 97 RON leaded
Lubrication
Type Wet sump, pressure fed
Pump type Crankshaft driven eccentric rotor
Oil filter Disposable canister with full flow by-pass
Pressure at idle - minimum 0.7 bar (10 lbf.in
2)
Pressure at 2000 rev/min (hot) 3.4 bar (50 lbf.in
2)
Relief valve opening pressure 3.4 bar (50 lbf.in
2)
Low oil pressure switch opening pressure 0.24-0.41 bar (3.5-6.0 lbf.in
2)
Crankshaft
Main journal diameter 63.487 - 63.500 mm (2.4995 - 2.520 in)
Crankpin journal diameter 55.500 - 55.513 mm (2.20 - 2.22 in)
End float 0.08 - 0.26 mm (0.003 - 0.010 in)
Maximum ovality 0.040 mm (0.002 in)
Main bearings
Quantity 5
Material Glacier Vandervell / AS 15
Diametrical clearance 0.015 - 0.016 mm (0.00059 - 0.00063 in)
Connecting Rods
Type Horizontally split big-end, plain small end
Distance between centres 155.120 - 155.220 mm (6.1071 - 6.1110 in)

GENERAL DATA
04-8
Fuel system - Td5
Type Direct injection from pressure regulated supply with cooled return
flow and in-line pressure regulator
Pressure regulator setting 4 bar (58 lbf.in
2)
Pump Electric two stage submersible
Pump output:

Low pressure 30 l/h (6.6 gal/h) (7.93 US gal/h) at 0.5 bar (7.25 lbf.in
2)

High pressure 180 l/h (39.6 gal/h) (47.55 US gal/h) at 4 bar (58 lbf.in
2)
Maximum consumption 30 l/h (6.6 gal/h) (7.93 US gal/h)
Injectors Electronic unit injectors
Injector nominal operating pressure:

Pre EU3 models 1500 bar (21750 lbf.in
2)

EU3 models 1750 bar (25500 lbf.in
2)
Filter In-line canister filter/water separator with water detection
Air cleaner Mann and Hummell P0037

GENERAL DATA
04-9
Fuel system - V8
Cooling system - Td5
Type Multiport injection from pressure regulated, returnless supply
Pump Electric submersible
Regulated pump output pressure 3.5 bar (50.75 lbf.in
2)
Fuel pump delivery 120 litres/hr (211 pints/hr) (234 US pints/hr)
Filter In-line canister
Air filter Mann and Hummell P0036
Type Pressurised, spill return partial flow, thermostatically controlled
Cooling fans 11 blade axial flow on viscous coupling and 11 blade axial flow
electric
Electric cooling fan switching points:
For A/C system:

On When vehicle speed is 50 mph (80 km/h) or less and ambient
temperature is 28 °C (82 °F) or more

Off When vehicle speed increases to 62.5 mph (100 km/h) or ambient
temperature decreases to 25 °C (77 °F)
For engine cooling during normal running:

On 110 °C (230 °F)

Off 105 °C (221 °F)
For engine cooling at ignition off (to counteract heat
soak):

On If, within 10 seconds of ignition off, engine coolant temperature is
105 °C (221 °F) or more

Off After 10 minutes or if engine coolant temperature decreases to
100 °C (212 °F)
Coolant pump Centrifugal impeller, belt driven from crankshaft
Thermostat Waxstat with pressure relief valve
Thermostat opening temperature:

Initial opening 82 °C (179 °F)

Fully open 96 °C (204 °F)
Expansion tank cap relief valve - system operating
pressure1.4 bar (20.3 lbf.in
2)
Fuel cooler thermostat opening temperature 82°C (179°F)

TORQUE WRENCH SETTINGS
06-2
Engine Td5
TORQUE DESCRIPTION METRIC IMPERIAL
ACE pump bolts25 Nm (18 lbf.ft)
A/C compressor bolts 25 Nm (18 lbf.ft)
Alternator support bracket to cylinder head bolts 25 Nm (18 lbf.ft)
Alternator/vacuum pump oil feed pipe union 10 Nm (7 lbf.ft)
Camshaft cover to camshaft carrier bolts 10 Nm (7 lbf.ft)
Camshaft sprocket to camshaft bolts 37 Nm (27 lbf.ft)
Centrifuge cover bolts 10 Nm (7 lbf.ft)
Centrifuge oil drain pipe to sump bolts (or nuts) 10 Nm (7 lbf.ft)
Centrifuge to oil drain pipe bolts 10 Nm (7 lbf.ft)
Centrifuge to oil cooler housing bolts 25 Nm (18 lbf.ft)
CKP sensor bolt10 Nm (7 lbf.ft)
Coolant pipe bolt50 Nm (37 lbf.ft)
Connecting rod bolts, then a further 80°20 Nm (15 lbf.ft)
Crankshaft pulley bolt 460 Nm (340 lbf.ft)
Crankshaft pulley TV damper bolts 80 Nm (59 lbf.ft)
Crankshaft rear oil seal housing bolts 10 Nm (7 lbf.ft)
Cylinder head bolts initial tighten 30 Nm (22 lbf.ft)
Cylinder head bolts final tighten, then a further 90°, then a further 180° and finally a
further 45°65 Nm (48 lbf.ft)
Dipstick tube to camshaft carrier bolt 10 Nm (7 lbf.ft)
Drive plate (automatic transmission) to crankshaft bolts 115 Nm (85 lbf.ft)
EGR pipe clamp to cylinder head bolt - if fitted 25 Nm (18 lbf.ft)
EGR pipe Allen screws 10 Nm (7 lbf.ft)
Engine mounting (front) to cylinder block bolts 48 Nm (35 lbf.ft)
Engine mounting (front) to chassis nuts 85 Nm (63 lbf.ft)
Engine mounting bracket (rear, LH & RH) to gearbox bolts 85 Nm (63 lbf.ft)
Engine mounting bracket (rear, LH & RH) nuts 45 Nm (33 lbf.ft)
Flywheel to crankshaft (manual transmission) bolts, then a further 90°40 Nm (30 lbf.ft)
Front crossmember bolts 26 Nm (20 lbf.ft)
Fuel connector block bolts 25 Nm (18 lbf.ft)
Fuel cooler to inlet manifold bolts 25 Nm (18 lbf.ft)
Gearbox housing to engine bolts 50 Nm (37 lbf.ft)
Heater pipe to cylinder head bolts 25 Nm (18 lbf.ft)
Main bearing cap bolts then a further 90°33 Nm (24 lbf.ft)
Oil cooler housing to cylinder block bolts 25 Nm (18 lbf.ft)
Oil cooler pipe clip bolts 10 Nm (7 lbf.ft)
Oil filter adaptor housing to oil cooler housing bolts 25 Nm (18 lbf.ft)
Oil pick-up strainer screws 10 Nm (7 lbf.ft)
Oil pressure switch 15 Nm (11 lbf.ft)
Oil pump drive sprocket bolt 25 Nm (18 lbf.ft)
Oil pump pressure relief valve plug 25 Nm (18 lbf.ft)
Oil pump and stiffener assembly to cylinder block bolts 13 Nm (10 lbf.ft)
Oil sump to cylinder block bolts 25 Nm (18 lbf.ft)
Oil sump to gearbox bell housing bolts 13 Nm (10 lbf.ft)
PAS pump bracket bolts 27 Nm (20 lbf.ft)
PAS pump pulley bolts 27 Nm (20 lbf.ft)
Rocker arm adjusting screw locknuts 16 Nm (12 lbf.ft)

TORQUE WRENCH SETTINGS
06-3
Rocker shaft bolts 32 Nm (24 lbf. ft)
Timing chain adjustable guide bolt 25 Nm (18 lbf.ft)
Timing chain cover bolts 27 Nm (20 lbf.ft)
Timing chain cover to cylinder block stud 7 Nm (5.2 lbf.ft)
Timing chain fixed guide retaining pin 25 Nm (18 lbf.ft)
Timing chain cover to cylinder head nut and bolt 25 Nm (18 lbf.ft)
Timing chain fixed guide (M6) bolt 10 Nm (7 lbf.ft)
Timing chain fixed guide (M10) bolt 45 Nm (33 lbf.ft)
Timing chain lubrication jet bolt 10 Nm (7 lbf.ft)
Timing chain tensioner 45 Nm (33 lbf.ft)
Torque converter to drive plate (automatic transmission) bolts 50 Nm (37 lbf.ft)
Turbocharger heatshield bolts 10 Nm (7 lbf.ft)
Turbocharger oil feed pipe banjo bolt 25 Nm (18 lbf.ft)
Turbocharger to exhaust manifold nuts 30 Nm (22 lbf.ft)
Vacuum pump oil feed pipe to cylinder head union 10 Nm (7 lbf.ft)
Viscous fan nut45 Nm (33 lbf.ft)
Fuel spill return pipe unions - if fitted 20 Nm (15 lbf.ft)TORQUE DESCRIPTION METRIC IMPERIAL

TORQUE WRENCH SETTINGS
06-5
Emission control - Td5
Emission control - V8
Engine management system - Td5
TORQUE DESCRIPTION METRIC IMPERIAL
EGR valve pipe Allen screws 10 Nm (7 lbf.ft)
EGR valve to inlet manifold bolts 10 Nm (7 lbf.ft)
EGR intake pipe clip to cylinder head bolts - if fitted 25 Nm (18 lbf.ft)
EGR cooler to cylinder head nut and bolts - if fitted 25 Nm (18 lbf.ft)
TORQUE DESCRIPTION METRIC IMPERIAL
HO
2S Sensors45 Nm (33 lbf.ft)
SAI air manifold union nuts 25 Nm (18 lbf.ft)
Rubber mountings to SAI pump bracket 10 Nm (7 lbf.ft)
SAI control valve to manifold bolts 10 Nm (7 lbf.ft)
SAI pump to bracket nuts 10 Nm (7 lbf.ft)
SAI pump bracket to body bolt 20 Nm (15 lbf.ft)
Vacuum reservoir to mounting bracket bolt 10 Nm (7 lbf.ft)
TORQUE DESCRIPTION METRIC IMPERIAL
ECT sensor15 Nm (11 lbf.ft)
Fuel tank cradle45 Nm (33 lbf.ft)
CKP sensor10 Nm (7 lbf.ft)
MAP and IAT sensor 10 Nm (7 lbf.ft)
Fuel cooler to inlet manifold - upper bolts 25 Nm (18 lbf.ft)
Turbocharger to exhaust manifold 30 Nm (22 lbf.ft)
Turbocharger drain pipe 10 Nm (7 lbf.ft)
Banjo bolt to oil feed pipe 25 Nm (18 lbf.ft)
Fuel temperature sensor 14 Nm (10 lbf.ft)
Pressure regulator 25 Nm (18 lbf.ft)
Glow plugs16 Nm (12 lbf.ft)
EUI clamp bolts32 Nm (24 lbf.ft)
EGR valve to exhaust manifold 10 Nm (7 lbf.ft)
EGR valve to inlet manifold 10 Nm (7 lbf.ft)
EGR clip25 Nm (18 lbf.ft)